Maytag W10267633A Electric Dryer Power Hookup, Electrical Requirements, It is your responsibility

Page 4

ELECTRIC DRYER POWER HOOKUP

Electrical Requirements

It is your responsibility

If your outlet looks like this:

To contact a qualified electrical installer.

To be sure that the electrical connection is adequate and

in conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved in

remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

4-wire receptacle

(14-30R)

Then choose a 4-wire power supply cord

with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft. (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green or bare.

The neutral conductor must be identified by a white cover.

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt

electrical supply, if specified on the serial/rating plate) on

a separate 30-amp circuit, fused on both sides of the line.

A time-delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. Do not have a fuse in the neutral

or grounding circuit.

Do not use an extension cord.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that

the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground conductor is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground conductor must be removed from the external ground connector (green screw), and secured under the neutral terminal (center or white wire) of the terminal block. When the neutral ground conductor

is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the neutral conductor.

If local codes do not permit the connection of a neutral ground wire to the neutral wire, see “Optional 3-wire connection” section.

A 4-wire power supply connection must be used when

the appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through

the neutral is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductors.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:

A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.

A UL listed strain relief.

If your outlet looks like this:

Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft

(1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R.

3-wire receptacle

(10-30R)

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire) and be:

Flexible armored cable or nonmetallic sheathed copper cable (with ground wire), protected with flexible metallic conduit. All current-carrying wires must be insulated.

10-gauge solid copper wire (do not use aluminum) at least 5 ft. (1.52 m) long.

4

Image 4
Contents Table of Contents Dryer SafetyInstallation Requirements Tools and PartsOptional Equipment Parts suppliedLocation Requirements Electric Dryer Power Hookup Electrical RequirementsIt is your responsibility Electrical ConnectionStyle 1 Power supply cord strain relief Style 2 Direct wire strain reliefInstall strain relief Electrical ConnectionWire connection Power supply cord If your home has You will be Go to Section Connecting toWire connection Direct wire Remove center, silver-colored terminal block screwBDE CG F Optional 3-wire connection If using an existing vent system VentingVenting Requirements If this is a new vent system Vent materialOptional exhaust installations Alternate installations for close clearancesSpecial provisions for mobile home installations Plan Vent SystemInstall Leveling Legs Install Vent SystemConnect Vent Connect Inlet Hose Steam ModelsLevel Dryer Complete InstallationSteam Models Only Reverse Door Swing Reinstall the doorReverse the strike Troubleshooting Dryer OperationNo heat Dryer will not run Dryer displaying code messageDryer Results

W10267633A specifications

The Maytag W10267633A is a highly regarded appliance that exemplifies quality and durability in everyday home use. Designed for busy households, this model is a top-loading washing machine that seamlessly integrates functionality with convenience. Aimed at providing thorough cleaning performance, the W10267633A is equipped with a variety of features that enhance user experience and efficiency.

One of the main highlights of the Maytag W10267633A is its powerful Agitator system. This traditional mechanism is rooted in effective cleaning, enabling a robust wash action that agitates clothes for optimal dirt removal. Paired with the machine’s large capacity, which allows for bigger loads, users can tackle laundry days much more efficiently.

Another significant feature of this model is its Adaptive Wash Technology. This feature automatically senses the size of the load and adjusts water levels accordingly. Through this innovation, the washing machine conserves water while ensuring that each load is thoroughly cleaned, regardless of size.

In terms of cycle options, the Maytag W10267633A doesn't disappoint. It offers multiple wash cycles, including options for heavy-duty, delicate, and quick wash settings. This versatility allows users to customize their washing experience based on the fabric types and soil levels, making it a versatile addition to any laundry room.

The machine also prioritizes energy efficiency, meeting the standards set by the Energy Star program. This not only translates to potential savings on utility bills but also contributes to a more sustainable household. The durability of the appliance is bolstered by its stainless steel tub, which resists chipping and snagging, ensuring that clothes remain in good condition over time.

For added convenience, the Maytag W10267633A is designed with a user-friendly control panel, making it easy to choose cycles and adjust settings. Additionally, the machine is built with a solid foundation that minimizes vibration during operation, leading to a quieter washing experience.

Overall, the Maytag W10267633A is a dependable washing machine that pairs robust cleaning capabilities with modern technology and user-oriented features. Its smart design, efficient energy consumption, and versatility make it an excellent choice for families who value both performance and convenience in their laundry appliances.