JVC UX-MD9000R manual Adjusting the Volume, Reinforcing the Bass Sound, Tone Control BASS/TREBLE

Page 11

Adjusting the Volume

You can adjust the volume level between 0 and 50.

The VOLUME indicator on the display indicates the volume level.

VOLUME

Press the VOLUME UP button of the Unit to increase the volume or press the VOLUME DOWN button to decrease it.

OR

Press the VOLUME + button on the Remote Control to increase the volume or press the VOLUME - button to decrease it.

CAUTION: DO NOT start playing any source with- out first setting the VOLUME control to minimum position, as a sudden blast of sound can damage your hearing, speakers and/or headphones.

For private listening

Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers.

Be sure to turn down the volume before connecting or putting on headphones.

Reinforcing the Bass Sound

(AHB SUPER PRO)

You can reinforce the bass sound to maintain rich, full bass at low volume (you can use this effect only for playback):

To get the effect, press the AHB (Active Hyper Bass) SUPER PRO button on the Remote Control.

The “BASS” indicator lights up on the display. To cancel the effect, press the button again. The “BASS” indicator goes out.

Tone Control (BASS/TREBLE)

You can control the tone by changing the bass and treble.

BASS Control ———————————

You can adjust the bass level (low frequency range level) between –6 and +6. (0: Flat)

■1. Press the BASS button on the Remote Con- trol.

■2. Press the UP or DOWN button on the

Remote Control to adjust the bass level.

BASS

DOWN

UP

TREBLE Control ——————————

You can adjust the treble level (high frequency range level) between –6 and +6. (0: Flat)

■1. Press the TREBLE button on the Remote

Control.

■2. Press the UP or DOWN button on the

Remote Control to adjust the treble level.

TREBLE

DOWN

UP

■ The bass or treble level display goes out when the BASS or

English

TREBLE button is pressed again or when nothing is done for

 

about 6 seconds.

 

Showing the Time (CLOCK)

 

In Standby mode, the clock appears on the display.

When the System is turned on, you can display the clock at any time. To display the clock, press the CLOCK button.

To light off the clock, press the CLOCK button again.

Note: To let work the clock, you need to set the clock beforehand. (See "Setting the Clock" on page 22.)

7

Page 10 Page 12
Image 11
Page 10 Page 12
Contents UX-MD9000R Achtung Side view Seitenansicht Côt Zijaanzicht Vista lateral Produit Laser Classe Klas 1 Laserprodukt Table of Contents Getting Started AccessoriesHow To Put Batteries In the Remote Control Using the Remote ControlUsing the Coaxial Type Connector Not Supplied Connecting the FM AntennaConnecting the AM MW/LW Antenna Using the Supplied Wire AntennaRemoving the speaker grilles Connecting the SpeakersConnecting External Equipment Connecting a Tape Deck, etcConnecting Auxiliary Equipment Connecting a CD Player, etc Digital Input AUX2Connecting a Subwoofer System Connecting the AC Power CordTurning the System On Turning the Power On and OffAdjusting the Brightness Dimmer Common OperationsShowing the Time Clock Adjusting the VolumeReinforcing the Bass Sound Tone Control BASS/TREBLEManual Presetting Using the TunerTuning In a Station Presetting StationsReceiving FM Stations with To Change the FM Reception ModeSelect the programme type with the 4 or To select a programme typePress the PTY/EON button within 10 sec Onds againTo Insert a CD Using the CD PlayerBasics of Using CD Player-Normal Play Repeating Tracks ProgrammingPlaying Order of the Tracks Random PlayTo Play an MD Using the MD Player Listening to an MDBasics of Using MD Player Normal Play To Insert an MDTo confirm the programmed tracks while the MD Player is Recording Indication of the MD Indicator for RecordingRecording onto an MD Standard RecordingCD Synchro Recording Using the MD Player EditingGiving titles to discs and tracks Title function Dividing Tracks Divide FunctionErasing all the tracks ALL Erase function Erasing Tracks Erase Function Joining TracksJoin Function Moving Tracks Move FunctionSelect the track number to be erased Erasing all the Tracks ALL Erase FunctionGiving Titles to MD Disc TI- TLE/TITLE Function Press the EDIT/TITLE button until Erase ? is displayedNumbers Input a preferred title up to 32 charac- tersPress the EDIT/TITLE button again Character Layout TableListening to External Recording to External Equipment Using External EquipmentsWhen the AUX 1 Analog in is selected When the AUX 2 Digital in is selectedSetting the Daily Timer Using the TimersSetting the Clock Information on MDs Minidiscs Setting the Sleep TimerSound skip guard memory MD Minidisc Error MessagesUtoc User Table Of Contents Atrac Adaptive Transform Acous- tic CodingCondition Cause Minidisc limitationsRules of Digital Dubbing Scms Serial Copy Management SystemCare And Maintenance Symptom Possible Cause Action TroubleshootingSpecifications EN, GE, FR, NL, SP, IT 0598MNMCREOZK
Top Page Image Contents