1Congratulations, Panele, Phillips screwdriver

Move washer/dryer to its permanent location.

placing a carpenter’s level on top of washer, first side to side then front to back. If it is not level, screw the front legs up or down to adjust. Tilt washer/dryer forward raising back legs 1” off of floor to adjust rear self- leveling legs. Gently lower washer to floor. Make final check with level.

Put “hook” end of drain hose in tub or standpipe. Tightly wrap the plastic strap around the drain hose and tub or standpipe or inlet hose as shown in Figures A-C.

If drain hose cannot be strapped in place, it must be cut exactly to length so the “hook” end is held tightly over the edge of the tub or standpipe.

If a longer drain hose is needed, drain hose (Pat No. 388423) and hose extension kit (Part No. 285442) are available from a

Whirlpool-authorized parts distributors. If drain hose must be shortened, use hose kit (Par-t No. 285442).

Note: If washer/dryer is moved to adjust drain hose, the washer/dryer must be leveled again. Repeat Step 20. Place cardboard under the washer/dryer and carefully move washer/dryer to avoid damaging floor covering.

Remove the two foam shipping pieces between washer and

dryerand place with othershipping pieces. If the exhaust ductwork cannot

be connected from the side of the washer/dryer, the exhaust duct can be reached from the front, through the access panel. Remove the access panel by unscrewing 2 phillips head screws located at the top of the panel. Set panel and screws aside.

PANELE

23.

To exhaust the dryer straight from back of the washer/dryer unit, determine if any additional exhausl duct is needed (see exhaust requirements, Panel B ). To exhaust the dryer to either side or inside check if additional exhaust duct is needed and see Alternate Exhaust Methods, Panel F Connect exhaust duct to exhaust hood.

Use duct tape to seal all joints.

25.

CHECK ELECTRICALREQUIREMENTS. BESUREYOU HAVECORRECT ELECTRICALSUPPLYAND RECOMMENDEDGROUNDING METHOD.Check the installation instructions to see that you have completed each step. Complete

any missed steps before you

26.

Check that all parts are now installed. See parts list, Panel B. If there is an extra part, go back through steps to see which step was skipped.

27,

Check that you removed all the shipping pieces including the three shipping straps with keys.

If you do not remove the shipping straps, your washer/dryer may ‘Walk” away from its location.

phillips screwdriver

Check that you have all of your tools, ’

29.

Turn on water faucets and check for leaks. Tighten couplings if there is leaking.

30.

Plug electrical cord into grounded outlet.

31.

If access panel was removed to install ductwork, replace access panel. Be sure to tighten both screws.

32.

Take a few minutes and read the Use and Care Guide to fully understand your new washer/dryer. Now start the washer and allow it to complete the regular cycle.

Remove tape from dryer door and open door. Remove the tape across the dryer lint screen. Check to be sure lint screen is in its proper position. Wipe out drum. Start dryer and allow it to complete a cycle to make sure the dryer is working properly

34.

Finally, save all literature and keep with the washer/dryer, Save all shipping materials for reshipping.

new Whirlpool washer/dryer.

To get the most efficient use from your new washer/dryer, read your Whirlpool Use and Care Guide.

1Congratulations! )

Keep installation instructions

~~~~~~

3397512 specifications

The Whirlpool 3397512 is a highly regarded replacement dryer heating element designed to restore your appliance's heating capabilities effectively. It is particularly popular among homeowners looking to replace a faulty heating element in their Whirlpool dryers. This part is compatible with a wide range of dryer models, ensuring that users can benefit from the heating solution it provides.

A standout feature of the Whirlpool 3397512 is its robust construction, designed to withstand the rigors of frequent use. Made from high-quality materials, it ensures longevity and durability, minimizing the need for frequent replacements. This feature is crucial for maintaining the efficiency of your dryer over time.

One of the key technologies incorporated in the Whirlpool 3397512 is its advanced heating design, which promotes even heat distribution. This ensures that clothes are dried uniformly, preventing instances of damp spots that can occur with inferior heating elements. This technology not only enhances the drying process but also contributes to fabric care, reducing wear and tear on clothes.

The Whirlpool 3397512 is engineered for easy installation, making it accessible for DIY enthusiasts as well as casual users. The design features straightforward connections that can be made with minimal tools, allowing users to quickly restore their dryer’s functionality without the need for professional assistance.

Moreover, the efficiency of the Whirlpool 3397512 aligns with modern energy-saving standards. It operates effectively at optimal temperatures, reducing energy consumption while providing powerful drying capabilities. This efficiency can lead to lower utility bills and a smaller carbon footprint, making it an environmentally conscientious choice.

In addition, compatibility is another essential characteristic of the Whirlpool 3397512. It fits various Whirlpool dryer models, making it a versatile solution for many households. This wide compatibility ensures that when the heating element needs replacing, homeowners can easily find a suitable option without facing the hassle of extensive searches or waiting on special orders.

In conclusion, the Whirlpool 3397512 heating element is an essential component that enhances the performance of compatible Whirlpool dryers. Its robust construction, advanced heating design, ease of installation, and energy efficiency make it a preferred choice among consumers looking to maintain their dryers in optimal working condition. By choosing the Whirlpool 3397512, users can enjoy a reliable and efficient drying experience.