Haier HWM70-0588 Safety precautions, Trouble-shooting answer to question, Common phenomena

Safety precautions

Please plug the power plug on special	The washing machine must be					positioned
	so that the plug is accessible. Be sure to pull the
receptacle. Be sure to use three-pins	plug off and close the water faucet in
power receptacle. Ensure that the earthing	following cases: power failure, delivering
prong of the power receptacle is earthed	the	machine,	setting	the	machine idle or
reliably. Use leakage protector if possible.	c l e a n i n g t h e m a c h i n e .				D o	n o t	p l u g
	or	pull the	power	plug	with	wet	hand .

Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.

Keep the pin of the power plug clean, if the power plug is polluted with dust, please wipe with dry cloth carefully.

If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by the technicians of our special shop or our customer care agent.

In case the washing machine is installed on ground with	Do not use water hotter than 50 .
carpet, do not block the ventilation hole with carpet.

T h e v e n t i l a t i o n holes at the bottom

Carpet

Do not put the machine at damp place like	Do not wash water-proof laundries like
the bathroom. Never wash it with water. Do	the raincoat, bike covers etc. to avoid
not put wet laundries on the control panel.
	abnormal vibrations in spinning.

Do not let the machine share one receptacle with other electric appliances. If the plugging into the receptacle is loose, do not use the plug any more.

2

Trouble-shooting answer to question

(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.

Phenomena		The reason	How to settle
The digitron displays E0.		The top lid is opened during reserve procedure.	Close the top lid.
The drainage cannot work, or is too slow.		Is the drain hose put down?	Put down the drain hose. Open and close the top lid once.
The digitron displays E1.		Is the drain hose blocked?	Clean the foreign material. Open and close The top Lid Once.
It stops running in midway. The digitron		The top lid is not closed.	Close the top lid.
displays E2.
The safety switch acts, and the		Are the laundries put slantingly?	Reorder the laundries. Close the top lid.
spinning cannot work. The
		Is the machine slanting?	Th machine will start running after 10
digitron displays E3.			seconds of being placed horizontally.
		Is the water tap opened, or is there water	Open the water tap. Push the start/Pause
The water filling does not work, or is			button once.
		supply failure?
slow. After about 15 minutes later,			Clean the water inlet valve then push
		Is the water inlet valve blocked?
			the Start/Pause button once.
the digital displays E4.
		Is the water pressure too low?
			Push the Start/Pause button once.
The digitron displays E6.		The water level sensor is bad.	Please contact the after-sales
			service department.
The digitron displays E7.		The communication is bad.	Please contact the after-sales service
			department.
	Not wash	Is there power failure?	Please use it when there's power supply.
The machine does		Is the power plug inserted tightly?	Insert the power plug tightly.
		Is the water level reached preset position?	Fill water to the preset position.
not act
	Not spin	Is the power plug inserted tightly?	Insert the power plug tightly.
		Is the top lid closed reliably?	Close the top lid.
		Are the laundries set flat?	Set the laundries flat.
There's abnormal sound		Is the machine slanting?	Adjust the machine to be even
		Are the laundries put slantingly in spinning?	Reorder the laundries and close the top lid.
inside the machine
		Are there any foreign materials?	Remove the foreign materials.
The water tap leaks		Is the screw of the jointer of water	Fasten the screw of the jointer properly.
		inlet hose loose or awry?

Common phenomena

Phenomena	Explanation
The spinning is intermittent when it starts.	Balance the laundries to avoid slanting.
The wash procedure is paused.	The cloth sensor is checking the cloth, it willadd waterafter 48 seconds.
Push the PROGRAM button to select SPIN,	The program is setting the drain time. Some time is needed
but it doesn't work.	before it starts spinning.
The pulsator pauses during water inlet	It is to avoid splashing during water inlet.
in wash and rinse.
There may be some water flowing out of the	It is the water remained in the factory inspection of performance.
drain hose in the first use of the machine.