Install the water inlet hose
Confirm the water faucet
Water faucet,suitable | Water faucet,not suitable |
Outlet end surface |
|
>10mm |
|
It is required that the front end shall be longer than 10mm.
Reserve, remain time digitron
It displays
It displays remained reserve time (hour).
It displays total remained time (min). If the total time exceeds 99 minutes, it uses "A" on tens digit to represent100 minutes, and uses "b" to represent 110 minutes. E.g. "A3" represents 103 minutes.
It displays abnormal symbol in abnormal situation. (See to Page15)
"Air dry"button
. Push the button to toselect the different air dry time(60
120
180
).
Minutes .To select 60minutes can dry the inner or outer tub . To select 120 or 180minutes can dry clothes.(both lighter is on indicate the 180minutes program).The weight of the clothes is 1.5kg at most.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the water inlet hose component. See to Figure 1.
2.Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet. See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
Remain | Program |
|
| |
|
|
|
|
|
|
|
|
|
|
|
| Standard |
| Normal |
|
|
|
|
|
|
|
|
|
|
|
| Woollen |
| Quick |
|
|
|
|
|
|
|
|
|
|
|
| Carpet |
| Posthaste |
|
|
|
|
|
|
|
|
|
|
Reserve |
| Saving water |
| Jean |
|
|
|
| |
|
|
|
| |
Reserve | Program |
| LOCK |
••
•
• 
•
• | • | Air dry |
|
• | • | 120 |
|
• | • | 60 |
|
| Water | Air | dry |
|
| ||
| level |
|
|
"POWER" button
Push the "POWER" button to switch on the power. 
Under
Power
On/off
water inlet hose jointer
Slider
Screw
Sign plate
Lock level
Screw knife
Bushing
"RESERVE" button
"PROGRAM"button
"WATER LEVEL"button
water inlet hose
Figure 1
Figure 2 | Figure 3 |
The digitron displays the time remained (in minute) before the washing is finished.
Following
Program | Application |
Normal | Washing for normal laundries |
The washing machine can detect the laundries automatically. After detection, it will set the water level to suitable value among 4, 6, 8,and 10 automatically.
You can also set water level by yourself. After the machine is
3.Fasten the four screws evenly. See to Figure 4.
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure to seal up the exit end face of the faucet. See to Figure 5.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
About 4mm before twisting
Push down the reserve button. The reserve indicator light is on the digitron displays the reserve time of finishing washing (in hour).The time remain indicator light is on, indicating that the reserve function is running.
Push the reserve button can display the reserve state.
Quick | Quick washing for normal laundries | |
Posthaste | Washing for | a few laundries |
Jean | Washing for big and thick laundries | |
Standard Standard saving washing for normal laundries
Woollen | Washing for the woollen laundries, |
| under 2.5kg |
Carpet | Washing for carpet and wearing bigger |
| Laundries, under 3.0kg |
Saving water | Saving washing for |
started, it will not set water level automatically. You shall push the start/pause button to make new setting.
If there's water inside the tub, the machine cannot detect the laundries and will display water level 6 .If wet laundries are put in, it may display water level 10. You must set suitable water level by yourself.
If Posthaste program is selected, it will display water level 3 .
When water level 2 is reached in water filling, it will perform washing while filling water. When water level 3 is reached, it will change to normal washing.
During operation of wash and rinse program, you can push down the water level button to add water. When you release the button, or it reaches the overflow water level, the machine will stop adding water.
Screw nut
About less than 2mm after twisting
The water level decided may be different from actual value because of the different moisture level of the laundries.
Figure 4 | Figure 5 | Figure 6 |
|
|