Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine.
Install the Inner cover component
Before initial use of the machine, assemble the inner cover as described below:
1.Open the top lid of the washing machine. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
2.Put the inner cover component on the outer tub cover, aiming |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
the inner cover shaft to the installation hole of the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Outer tub cover | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
corresponding outer tub cover shaft groove. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Outer tub cover shaft groove | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
3.Firstly insert the inner cover shaft of one side into the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Inner | cover shaft | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Inner | cover | ||||||||
corresponding outer tub cover shaft groove, then push |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
the another inner cover shaft into the corresponding |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Damping cushion | ||||||||
outer tub cover shaft groove. Please install to designated |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
position to guarantee there are no dropping or abnormal |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
sound in opening and closing of the inner cover, and the |
|
|
|
|
|
|
|
|
|
| Push |
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||
operation shall be smooth. Do not dismount the inner cover |
|
|
|
|
|
| Section I enlarging |
|
|
|
|
| |||||||||||||||
component after washing. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
3 Push "SOAK" 
"WASH/SPEED" 
"RINSE" 
"SPIN/SPEED" button to select suitable procedure program
Attention
Even there's no water in the tub, a certain period is required before spin starting. Separate the laundries that are not colorfast from other laundries in washing.
The soak procedure can work in cooperation with automatic programs like normal, comforter There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing, and can not make setting in other cases.
If the water pressure is too low, in order to wash the cloth cleanly, the machine will change from " SAVING WATER "to "storing water "automatically.
4 Push the " WATER LEVEL "button, select suitable water level
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth. After defection, it can set the water level automatically. To select other water level, first push the "START/PAUSE"
Install the bottom plate
After you open the package, please lean the washing machine gently down on soft items ( like the towel cloth, blanket, etc. ). Install the bottom plate to the bottom of the machine, then lift the machine up gently. See to the figure:
Two claws at the bottom cover shall be inserted in two
I
Back
Front
Soft items | Bottom plate |
Section I enlarging
button, then push the "WATER LEVEL" button to set the water level.
5 Push the "AIR DRY"button to select suitable dry time.
6 Push the "RESERVE" button to select suitable reserve wash program
After switching on the power, the reserve program is set to off mode automatically. If you need to set the washing procedure to be finished at reserved time, please push the " RESERVE " button to set the reserve wash program. Refer to reserve button in Page 11 for selection.
Confirm the operation of reserve program
Adjust the Installation position
The largest allowable slope of the shank base of the machine is 2 
.The slanting or rough ground will result in unstable running or stoppage of the machine. Please adjust it with following methods:
When the "RESERVE" function is activated, the indicator light of the program you have set will be off. The "reserve (hour)" and "time remain" indicator lights will
be on. During reserve procedure, push the "RESERVE" button to display the reserve mode. To change the running program or cancel the reserve setting, you
need to switch off the power and make new selection.
Confirm it's horizontal:
Hang the lead line to check if it is horizontal.
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the side of the leg slightly, loosen the adjustable nut, and twist the leg.
2 . After adjustment, fasten the nut.
|
|
|
|
|
|
| the adjustable nut |
Loosen |
|
|
|
|
|
| Fasten |
|
|
|
|
|
| the adjustable feet | |
High |
|
|
|
| Low | ||
7 Push the "START/PAUSE" button
5 Close the top lid | 6 Finish washing | |
|
| |
As the top lid opened, the washer will automatically |
| After finishing wash it'll |
| alarm and switch off power | |
given alarm and stop running, exclusively during |
| |
| automatically | |
draining. |
| |
|
|
|