Humminbird MATRIX 12, MATRIX 37, Matrix 20, MATRIX 17 Depth Offset, Temp Offset, To Select Readouts

Page 26

Default Sonar View

Customized Sonar View

To Select Readouts:

1.Make sure you are in Advanced User Mode, then highlight Select Readouts on the Setup main menu.

2.Use the RIGHT 4-WAY Cursor Control key to initiate this procedure.

3.The Select Readouts submenu will appear, showing a list of all Readouts. Use the UP or DOWN Cursor keys to select a particular Readout position, then use the RIGHT or LEFT Cursor keys to change what will be displayed at that position. (Off, Speed, Temperature, Triplog, Voltage, Water Speed)

Depth Offset

(Advanced)

Depth Offset will adjust the digital depth readout to indicate depth from the waterline or boat's keel. Enter a positive vertical measurement from the transducer to the waterline to read the depth from the waterline. Enter a negative vertical measurement from the transducer to keel to read the depth from the keel. This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.)

To change the Depth Offset setting:

1.Make sure you are in Advanced User Mode, then highlight Depth Offset on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Depth Offset setting. (-10.0 to +10.0 feet or -3 to 3 meters [International Models Only], Default = 0)

Temp Offset

(Advanced)

Temp Offset will adjust the temperature readout by the amount entered. This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.)

To change the Temp Offset setting:

1.Make sure you are in Advanced User Mode, then highlight Temp Offset on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Temp Offset setting. (-10.0 to +10.0 degrees, Default = 0)

45

46

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Operations Manual Table of Contents Thank YouAccessories Menu Tab Troubleshooting Alarms Menu TabSetup Menu Tab Sonar Menu TabDualBeam Plus Sonar How Sonar WorksSingle Beam Sonar QuadraBeam SonarHard Bottom What’s On the DisplayBait Ball Soft BottomUnderstanding Sonar History ViewsSonar View Sonar ViewFull range view Real Time Sonar RTS WindowSonar Zoom View Sonar Zoom ViewDualBeam Plus and QuadraBeamTM Only 200/83 kHz Split Sonar ViewBig Digits View 200/83 kHz Split Sonar ViewQuadraBeamTM Only Side Beam ViewBottom Presentation Digital readouts in the Side Beam View cannot be customizedView Key POWER/LIGHT KeyKey Functions Exit Key Menu KeyWAY Cursor Control Key Menu System Accessory BusPowering Up the Unit Start-Up Options Menu Normal OperationPC Connect SimulatorSystem Status With PC Connect Cable OnlySonar X-PressTMMenu To adjust the SensitivityTo adjust the Upper Range SensitivityBottom View Chart SpeedLower Range Sonar Menu Tab To adjust the Zoom LevelZoom Level Sonar Zoom View OnlyTo use Beam Select Beam SelectFish ID+TM Highlight Beam Select on the Sonar main menuKHz Balance Fish SensitivityKHz Sensitivity Depth Lines To change the Depth Lines settingTo change the Surface Clutter setting Surface ClutterWater Type Noise FilterMax Depth Transducer SelectFish ID Alarm Alarms Menu TabDepth Alarm Low Battery AlarmUnits Temp Setup Menu TabUnits Depth Units DistanceRestore Defaults User ModeTriplog Reset Units SpeedSelect Views Select ReadoutsDepth Offset To change the Depth Offset settingTo change the Temp Offset setting Temp OffsetNmea Output Accessories Menu TabSpeed Calibration Problem Possible Cause TroubleshootingDisplay Problems Control head loses power at high speedsIsolation Matrix Fishing System AccessoriesFinding the Cause of Noise Specifications Contact Humminbird
Related manuals
Manual 31 pages 35.86 Kb
Top Page Image Contents