Humminbird Tour Series Step Two Drill the Mounting Holes, Step Three Assemble the Transducer

Page 7

INSTALLATION

TRANSOM INSTALLATION

∙If the propeller(s) is (are) forward of the transom, it may be impossible to find an area clear from turbulence, and a different mounting technique or transducer type should be considered.

Step Two - Drill the Mounting Holes

1.Remove the mounting template from the front of the Operations Manual.

2.Hold the template on the transom of the boat in the location where the transducer will be installed (Figure 4). Align the template vertically, ensuring the lower edge of the transom meets with the bottom corner of the template.

3.Using a pencil or punch, mark the two mounting holes shown on the template onto the transom. Do not mark or drill any other holes at this time.

4.Using a 5/32” (4mm) bit drill the two holes to a depth of approximately 1" (3cm). On fiberglass hulls, it is best to start with a smaller bit and use progressively larger drill bits to reduce the chance of chipping or flaking the outer coating.

Step Three - Assemble the Transducer

1.Attach the Pivot to the transducer body as shown in Figure 5, using the #8 – 3/8” (9mm) long allen headed pivot screw, the headed pin, the two flat washers, and the two toothed lock washers.

Note: The toothed lock washers must be positioned between the transducer and the pivot ears. The flat washers must be positioned to the outside at the pivot ears.

2.Using the AIlen wrenches provided, loosely tighten the pivot screw (Figure 6). Do not completely tighten the assembly at this time, so the pivot angle can be adjusted later.

3.Insert the pivot/transducer assembly into the mounting bracket as shown in Figure 7. Do not snap the assembly closed.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Page Installation Overview AccessoriesParts Supplied Determining How to Mount the Transducer Thru-Hull Mounting Alternate Transducers and Mounting MethodsPortable Mounting Trolling Motor MountingTransducer Exchange Beginning InstallationStep One Determine Where to Mount the Transducer Transom InstallationStep Three Assemble the Transducer Step Two Drill the Mounting HolesStep Four Mount the Transducer to the Transom Step Five Adjust the Running Position of the TransducerStep Six Route the Cable Step One Determine the Mounting Location Inside the Hull InstallationStep Two Test the Mounting Location Step Three Permanently Mount the Transducer Step One Determine Where to Mount Control Head InstallationStep Two Connect the Power Cable to the Boat Step Four Run the Cables Step Three Drill the Mounting HolesYour Humminbird is now ready for operation Step Five Assembling the Connector HolderTest the Installation Testing the Installation Simulator Operation Feature MemoryWhat YOU see ON-SCREEN Interpreting the ON-SCREEN Information Control Functions Page Sensitivity Menu FunctionsDepth Range Zoom Fish Alarm Depth AlarmOptions TriplogFish ID UnitsTransducer Numeral SizeDisplay Speed ResetCustomizing SET-UP Functions Using DiagnosticUsing Alternative Transducers

Tour Series specifications

The Humminbird Tour Series stands out as a premier line of fish finders and sonars, designed specifically for anglers seeking advanced technology and durability on the water. Renowned for their high performance, the Tour Series incorporates cutting-edge features tailored for serious fishing enthusiasts.

One of the hallmark features of the Humminbird Tour Series is its superior imaging capabilities. The series boasts the latest in sonar technology, including Side Imaging and Down Imaging, which provide incredible detail and clarity below and beside the boat. This advanced sonar allows anglers to identify fish, structures, and underwater vegetation with unmatched precision, transforming the fishing experience into a more strategic and informed endeavor.

Another significant attribute of the Tour Series is its GPS capability. Equipped with Humminbird’s proprietary LakeMaster and Navionics maps, these devices allow users to navigate with confidence. The integration of GPS also enables the creation of custom waypoints, routes, and tracks, enhancing connectivity to fishing hotspots. The AutoChart Live feature lets anglers create real-time maps of their fishing spots that highlight depth contours and bottom hardness, offering a customized view of their fishing environment.

The Tour Series is built to withstand the demanding conditions of fishing. With a rugged design and a bright, sunlight-readable display, these fish finders ensure visibility in various environments. The touchscreen interface is intuitive and responsive, allowing for easy adjustments on the fly. Additionally, the models are equipped with a robust transducer system that can achieve impressive depths and deliver accurate readings even in challenging waters.

The integration of the 360 Imaging feature is another standout characteristic. This capability offers a complete panoramic view of the water around the boat, providing additional data on fish and structure location. The ability to see a complete picture of the surroundings allows anglers to make better decisions in real time.

Lastly, the Tour Series doesn’t compromise on connectivity. With built-in Bluetooth and networking capabilities, anglers can connect multiple devices simultaneously and share data seamlessly. Whether you are monitoring multiple fishing rods or collaborating with fellow anglers, the Tour Series provides the tools necessary to enhance your fishing excursions.

In summary, the Humminbird Tour Series combines advanced sonar technology, comprehensive GPS mapping, durable construction, and connectivity features, making it a leader in the fishing electronics market. For passionate anglers, it delivers not just tools, but a profound understanding of their aquatic environment.
Top Page Image Contents