Humminbird Tour Series manual Step Three Drill the Mounting Holes, Step Four Run the Cables

Page 13

INSTALLATION

CONTROL HEAD INSTALLATION

and one amp fuse (not included) for the protection of the unit (Figure 21). Humminbird is not responsible for over voltage or over current failures.

In order to minimize the potential for interference with other marine electronics a separate power source (such as a second battery) may be necessary.

Step Three - Drill the Mounting Holes

1.Set the mounting bracket in place on the mounting surface. Mark the four mounting screw locations with a pencil or punch.

2.Set the mounting bracket aside, and drill the four mounting screw holes using a 9/64” (3.6mm) bit.

Step Four - Run the Cables

1.If the cables must pass through a hole underneath the mounting surface, mark and drill a 1” (25mm) hole centered between the four mounting holes (Figure 22).

Note: if the cables must pass through the mounting surface at a different location, drill the 1" (25mm) hole at that location and pass the cables through from underneath. Also, you must break out the tabs on the rear of the mounting base using needle nose pliers (Figures 24-25).

2.Insert all cables through the 1” (25mm) hole from beneath the mounting surface.

3.Pass the cables through the grommet (if the cable hole is underneath the mounting bracket) then press the grommet in place around the cables and into the 1” (25mm) hole.

4.Pass the cables through the mounting base, out the top of the mounting bracket.

5.Place the mounting bracket on the mounting surface aligned with the drilled holes. Insert the four flathead wood screws into the mounting holes and tighten fully (Figure 23).

Optional: If the cables pass outside the mounting bracket, install the hole cover over the hole and fasten in place using the two #8 x 7/8” (22mm) wood screws (Figure 24).

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Page Installation Overview AccessoriesParts Supplied Determining How to Mount the Transducer Portable Mounting Alternate Transducers and Mounting MethodsTrolling Motor Mounting Thru-Hull MountingTransducer Exchange Beginning InstallationStep One Determine Where to Mount the Transducer Transom InstallationStep Three Assemble the Transducer Step Two Drill the Mounting HolesStep Four Mount the Transducer to the Transom Step Five Adjust the Running Position of the TransducerStep Six Route the Cable Step One Determine the Mounting Location Inside the Hull InstallationStep Two Test the Mounting Location Step Three Permanently Mount the Transducer Step One Determine Where to Mount Control Head InstallationStep Two Connect the Power Cable to the Boat Step Four Run the Cables Step Three Drill the Mounting HolesYour Humminbird is now ready for operation Step Five Assembling the Connector HolderTest the Installation Testing the Installation Simulator Operation Feature MemoryWhat YOU see ON-SCREEN Interpreting the ON-SCREEN Information Control Functions Page Sensitivity Menu FunctionsDepth Range Zoom Fish Alarm Depth AlarmOptions TriplogFish ID UnitsTransducer Numeral SizeDisplay Speed ResetCustomizing SET-UP Functions Using DiagnosticUsing Alternative Transducers

Tour Series specifications

The Humminbird Tour Series stands out as a premier line of fish finders and sonars, designed specifically for anglers seeking advanced technology and durability on the water. Renowned for their high performance, the Tour Series incorporates cutting-edge features tailored for serious fishing enthusiasts.

One of the hallmark features of the Humminbird Tour Series is its superior imaging capabilities. The series boasts the latest in sonar technology, including Side Imaging and Down Imaging, which provide incredible detail and clarity below and beside the boat. This advanced sonar allows anglers to identify fish, structures, and underwater vegetation with unmatched precision, transforming the fishing experience into a more strategic and informed endeavor.

Another significant attribute of the Tour Series is its GPS capability. Equipped with Humminbird’s proprietary LakeMaster and Navionics maps, these devices allow users to navigate with confidence. The integration of GPS also enables the creation of custom waypoints, routes, and tracks, enhancing connectivity to fishing hotspots. The AutoChart Live feature lets anglers create real-time maps of their fishing spots that highlight depth contours and bottom hardness, offering a customized view of their fishing environment.

The Tour Series is built to withstand the demanding conditions of fishing. With a rugged design and a bright, sunlight-readable display, these fish finders ensure visibility in various environments. The touchscreen interface is intuitive and responsive, allowing for easy adjustments on the fly. Additionally, the models are equipped with a robust transducer system that can achieve impressive depths and deliver accurate readings even in challenging waters.

The integration of the 360 Imaging feature is another standout characteristic. This capability offers a complete panoramic view of the water around the boat, providing additional data on fish and structure location. The ability to see a complete picture of the surroundings allows anglers to make better decisions in real time.

Lastly, the Tour Series doesn’t compromise on connectivity. With built-in Bluetooth and networking capabilities, anglers can connect multiple devices simultaneously and share data seamlessly. Whether you are monitoring multiple fishing rods or collaborating with fellow anglers, the Tour Series provides the tools necessary to enhance your fishing excursions.

In summary, the Humminbird Tour Series combines advanced sonar technology, comprehensive GPS mapping, durable construction, and connectivity features, making it a leader in the fishing electronics market. For passionate anglers, it delivers not just tools, but a profound understanding of their aquatic environment.
Top Page Image Contents