Humminbird 343c manual Start-Up Options Menu, Normal Operation, Normal Simulator System Status

Page 14

531447-1_A_343c_Eng.qxd 11/11/2005 9:18 PM Page 26

User Mode (Normal or Advanced) - An Advanced Mode is provided for users who desire the highest level of control over the Fishing System and Normal Mode for users who desire greater simplicity and fewer menu choices. Additional Advanced menu choices will be displayed throughout the menu system when you navigate to specific menus while in Advanced Mode. Any changes made while in Advanced Mode will remain in effect after you switch back to Normal Mode. See Setup Menu Tab: User Mode for specific instructions on changing to Advanced User Mode.

Sonar Tab, Normal Mode

Sonar Tab, Advanced Mode

Total Screen Update® - when you change any menu settings that affect the Sonar View, the view will update immediately (i.e. you don’t have to exit the menu to apply the change to the screen).

Start-Up Options Menu

Press the MENU key when the Title screen is displayed to access the Start-Up Options menu.

Use the UP or DOWN 4-WAY Cursor keys to position the cursor, then the RIGHT Cursor key to select one of the following choices. If you wait too long, the system will default to whichever menu mode happens to be highlighted:

Normal

Simulator

System Status.

Start-Up Options Menu

See the following paragraphs for more information about each of these choices.

Normal Operation

Use Normal operation for on the water operation with a transducer connected. In addition, your 300 Series™ Fishing System uses advanced transducer detection methods to determine if a transducer is connected. If a functioning transducer is connected, Normal operation will be selected automatically at power up and your Fishing System can be used on the water.

Exit Normal operation by powering your Fishing System off.

21

22

Image 14 Humminbird 343c manual Start-Up Options Menu, Normal Operation, Normal Simulator System Status
Contents 343c Operations Manual Table of Contents Thank YouTroubleshooting Alarms Menu TabSetup Menu Tab Specifications Glossary Contact HumminbirdHow Sonar Works DualBeam Plus Sonar What’s On the Display High Sonar Intensity Return Bait BallViews Sonar ViewFreeze Frame Understanding Sonar HistoryReal Time Sonar RTS Window Bottom Presentation Sonar Zoom View 200/83 kHz Split Sonar ViewKey Functions POWER/LIGHT KeyBig Digits View Circular Flasher ViewExit Key Menu KeyWAY Cursor Control Key Powering Up the Unit Menu SystemNormal Operation Exit Normal operation by powering your Fishing System offStart-Up Options Menu Normal Simulator System StatusExit System Status by powering your Fishing System off Self Test Accessory TestExit the Simulator by powering your Fishing System off SimulatorSensitivity To adjust the SensitivitySonar X-PressTMMenu Highlight Sensitivity on the Sonar X-PressTMMenuUpper Range To adjust the Upper RangeTo adjust the Lower Range Lower RangeBottom Lock Chart SpeedZoom Level Bottom RangeTo use Beam Select Sonar Menu TabBeam Select Highlight Beam Select on the Sonar main menuFish ID+TM To change the Fish ID Sensitivity settingTo change the RTS Window setting Fish ID SensitivityKHz Sensitivity Bottom ViewZoom Width Depth LinesMax Depth Surface ClutterNoise Filter Water Type Alarms Menu TabTo change the Water Type setting Low Battery Alarm Depth AlarmFish ID Alarm Temp AlarmTo change the Alarm Tone setting Alarm ToneSetup Menu Tab Highlight Alarm Tone on the Alarms main menuUnits Temp User ModeUnits Depth Units DistanceSelect Views Triplog ResetRestore Defaults Temp Offset Select ReadoutsDepth Offset Speed Calibration TroubleshootingTo change the Speed Calibration setting Finding the Cause of Noise Display ProblemsProblem Possible Cause IsolationSonar Terms SpecificationsGlossary 531447-1A343cEng.qxd 11/11/2005 918 PM 531447-1A343cEng.qxd 11/11/2005 918 PM Receiver See Transmitter 531447-1A343cEng.qxd 11/11/2005 918 PM Contact Humminbird