Humminbird 120 manual Step Six Route the Cable

Page 10

INSTALLATION

TRANSOM INSTALLATION

Step Six - Route the Cable

There are several ways to route the transducer cable to the to the area where the control head will be installed. The most common procedure routes the cable through the transom into the boat.

Inside the boat there is often a channel or conduit used for other wiring that the cable can be routed along. Do not cut or shorten the transducer cable and try not to damage the cable insulation. Route the cable as far as practical from the VHF radio antenna cables or tachometer cable to reduce the possibility of interference.

If the cable is too short, extension cables are available to extend the transducer cable up to a total of 50' (15 m). Call Humminbird Customer Support for more information.

Follow these steps to route the cable through the transom:

1.Drill a 5/8” (16mm) hole above the water line. Route the cable through the hole.

2.Fill the hole with silicone sealant.

3.Place the escutcheon plate over the hole and attach with the two #8 x 5/8” (16mm) screws.

4.Secure the cable by attaching the cable camp to the transom using a #8 x 5/8” (16mm) screw.

Note: The transducer will pivot up to 90 degrees in the bracket. Allow enough slack in the cable for this movement. It is best to route the cable to the side of the transducer so the cable will not be damaged by the transducer during movement.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Page Table of Contents Installation Overview Installation PreparationAccessories Parts SuppliedDetermining How to Mount the Transducer Trolling Motor Mounting Alternate Transducers and Mounting MethodsPortable Mounting Thru-Hull MountingBeginning Installation Transducer ExchangeTransom Installation InstallationStep One Determine Where to Mount the Transducer Step Two Drill the Mounting Holes Step Three Assemble the TransducerStep Five Adjust the Running Position of the Transducer Step Four Mount the Transducer to the TransomStep Six Route the Cable Step One Determine the Mounting Location Inside the Hull InstallationStep Two Test the Mounting Location Step Three Permanently Mount the Transducer Step One Determine Where to Mount Control Head InstallationStep Two Connect the Power Cable to the Boat Step Three Drill the Mounting Holes Step Four Run the CablesStep Five Assembling the Connector Holder Your Humminbird is now ready for operationTest the Installation Thank YOU Thank YOUUsing the Platinum ID HOW Sonar WorksUsing the Platinum ID Platinum ID Features Using the BUILT-IN Simulator Operating the Platinum IDPlatinum ID Functions Using the Platinum ID Factory Setting Fish Symbols Factory Setting MPH/SMSelecting Sensitivity Factory Setting +0 Enabling Fish Alarm Factory Setting OFF Using Bottom-Lock Factory Setting OFF Factory Setting One level below maximumFactory Setting on Automatic Factory Setting OFFSpecifications Maintenance and Warranty MaintenanceNothing happens when I turn the unit on TroubleshootingThere is no transducer detected There is no bottom reading visible on the display Get gaps in the reading at high speeds Unit comes on before I press POWER, and wont turn offMy unit loses power at high speeds Screen begins to fadeout. Images are not as sharp as normalHumminbird ONE Year Full Warranty Service Policy Customer Support

120 specifications

The Humminbird 120 is a pioneering fish finder that has gained recognition among anglers for its exceptional performance and user-friendly features. Designed with cutting-edge technology, this device offers a comprehensive suite of features that enhance fishing experiences on the water.

At the heart of the Humminbird 120 is its advanced sonar technology, which allows users to see fish and underwater structures with remarkable clarity. Equipped with dual-beam sonar, the device provides two different cone angles. The narrow beam offers high precision for locating specific targets, while the wide beam covers a larger area, making it easier to locate schools of fish.

One of the standout features of the Humminbird 120 is its easy-to-read display. The unit features a large, high-contrast screen with multiple color options, allowing users to customize their viewing experience. This clarity is essential, especially in bright sunlight or varying light conditions, ensuring that important information is visible at a glance.

In addition to fish identification, the Humminbird 120 packs a range of features designed to help anglers navigate their environment effectively. It includes advanced mapping capabilities, enabling users to create depth contours and view detailed underwater topography. This is particularly beneficial for identifying potential fishing hotspots and understanding the structure of the lake or riverbed.

The device also supports features such as temperature readings, which can be essential for understanding fish behavior and optimizing fishing strategies. The integrated GPS functionality further enhances usability by allowing users to mark waypoints, navigate through previously mapped areas, and avoid potential hazards while on the water.

Another practical aspect of the Humminbird 120 is its ease of installation and setup. Whether you have a small boat or a larger vessel, the device can be easily mounted and configured. The intuitive interface ensures quick access to functions, making it an excellent choice for both novice and experienced anglers alike.

Durability is also key in the design of the Humminbird 120. Built to withstand the rigors of regular use, the device is water-resistant and designed for various environmental conditions.

In summary, the Humminbird 120 combines advanced sonar technology, a clear display, effective mapping tools, and robust durability, making it a valuable asset for any angler looking to enhance their fishing experience. Whether you are searching for fish or exploring underwater terrain, the Humminbird 120 delivers reliability and performance on the water.
Top Page Image Contents