Kicker 10ZXM3504 manual Performance, Model ZXM350.4, Installation

Page 2

 

 

ZXM.4-SERIES AMPLIFIERS Owner’s Manual

Authorized KICKER Dealer:

 

 

 

Purchase Date:

 

 

Model Number:

ZXM350.4

 

 

 

 

Serial Number:

 

 

 

 

 

 

PERFORMANCE

 

 

Model:

ZXM350.4

RMS Power, all channels driven

 

 

@ 14.4V, 4Ω stereo, 1% THD+N

60W x 4

@ 14.4V, 2Ω stereo, 1% THD+N

90W x 4

@ 14.4V, 4Ω mono, 1% THD+N

175W x 2

Length

13-1/2” (342mm)

Specifications common to all models:

Height

2-1/8” (54mm)

Width

9-5/8” (244mm)

Frequency Response ± 1dB

20Hz–20kHz

Signal-to-noise Ratio

>95dB, A-weighted, re: rated power

Input Sensitivity

Low Level: 125mV–5V

 

 

High Level: 250mV–10V

Selectable Electronic Crossover

Variable HI, LO, or OFF (bypass) 50–200Hz, 12dB/octave

Bass Boost

Variable 0–18dB @ 40Hz

Pro Tip: To get the best performance from your new KICKER Amplifi er, use genuine KICKER accessories and wiring.

INSTALLATION

Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.

Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the amplifi er.

The ZXM amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifi er, the ZXM amplifi er’s input level switch should be set to “LO” and a low-level signal should run from the source unit’s stereo RCA output to the stereo RCA input on the end panel of the amplifi er using RCA interconnect cable. If a low- level stereo RCA output is not available on the source unit, the signal can be delivered to the amplifi er using the high-level speaker outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “HI”.

2

ZXM AMPLIFIERS

2010 ZXM 350.4 RevD.indd 2

1/15/2010 11:17:47 AM

Image 2
Contents ZXM Marine Amplifier Performance InstallationZXM350.4 Model ZXM350.4Model External Fuse Power/Ground Wire Protection LEDSTEREO-AND-MONO-SIMULTANEOUSLY Sams Operation Four Channel OperationBridged Operation Mono Minimum impedance of 2 ohms per channelOperation Troubleshooting ZXM350.4 Rendimiento Amplificador DE LA Serie ZXM.4Manual del propietario Modelo ZXM350.4Conexión a tierra o blindaje LED de protectionFuncionamiento Simultáneo EN Estereofónico Y Monofónico Funcionamiento POR Quatro CanalesFuncionamiento EN Puente Monofónico Impedancia mínima de 2 ohmios por canalFuncionamiento Resolución DE Problemas ZXM350.4 Leistung Verstärker DER ZXM.4 SerieBenutzerhandbuch Modell ZXM350.4≤18 OderModell Externe Sicherung Massekabel Gleichzeitiger STEREO- UND MONO-BETRIEB Sams VierkanalbetriebBrückenbetrieb Mono Minimalimpedanz von 2 Ohm pro KanalBetrieb Problembehebung Autoradio zur Karosserie zu verlegen Performances Amplificateur Série ZXM.4Manuel d’utilisation Modèle ZXM350.4Modèle Fusible Fil de Masse Externe Alimentation 45cmFonctionnement Simultané Stéréo ET Mono Sams Fonctionnement À Quatre CanauxFonctionnement Ponté Mono Impédance minimum de 2 ohms par canalUtilisation EN CAS DE Difficulté ZXM350.4 Electronics Limited Warranty What to do if YOU Need Warranty or ServiceInternational Warranty Garantía InternacionalStillwater Designs