Emerson manual SMMC-3 Control Panel Access Cover Removed, Gutter Sensor

Page 13

SMMC-3 CONTROL PANEL (ACCESS COVER REMOVED)

SMTS-1

Zone 1 Sensor

Input SMAS-1 or

SMGS-1 (Default)

Zone 2 Sensor

Input SMAS-1 or

SMGS-1

Zone 1 Sensor

Zone 1 Output

Input SMPS-1

Terminal Block

(must be programmed

Connector to

To activate)

Contactor Coil

 

(Default)

Zone 2 Input

Zone 2

 

for SMPS-1

Output

Fuse

 

 

“Fuse OK” LED

Zone 3 Sensor

Zone 3 Input

Zone 3

Input SMAS-1

for SMPS-1

Output

or SMGS-1

 

120VAC Power Connection

Temperature

Aerial Snow

Sensor, SMTS-1:

Sensor, SMAS-1:

this is included with

Mast mounted to

the SMMC-3 and

sense falling snow

must be installed

(may be used as the

outdoors to sense air

preprogrammed

temperature.

sensor).

PO. Box 726 n TULSA, OK 74101

n TEL 918-627-5530

Wiring guide on back of terminal block cover

Gutter Sensor,

In-Ground Sensor, SMPS-1:

SMGS-1:secured in

installed in-ground to detect

the gutter to detect

moisture and slab temperature

moisture conditions

(the SMMC-3 must be

(may be used as the

programmed to recognize this

preprogrammed

sensor, refer to the instruction

sensor).

manual for details).

n FAX 918-641-7336 n

www.nelsonheaters.com

GA-2318, R1

Sheet 13 of 15

May 2008

Image 13
Contents SMMC-3 Manual Table of Contents General Information PRE-PROGRAMMED ConfigurationGA-2318, R1 Snow/ice sensor options InstallationConnection to each sensor is described below PRE-PROGRAMMED ConnectionsBefore you energize the controller, confirm System CheckAfter energizing the controller, you should see To cycle system and check sensor operationMode 2 Priority Mode 1 IndependentOperation Outside T=-3C A1-A2-A3-P1-P2-P3-M1 Time Delay Zone 1 min.0 2.0H Max.10Zone Assignment Manual OperationMode No.2 2zones 3zones Mode No.1Degree C or F Ambient Off Temp. min.34 37F Max.50 Error!- SMPS-1 Cancel Manual only M1 Error!- SMTS-1 cancelError Messages Symptoms Probable Cause Correction Troubleshooting GuideTemperature Aerial Snow Sensor, SMTS-1 Sensor, SMAS-1 SMMC-3 Control Panel Access Cover RemovedGutter Sensor Sensor Extension Wire Specifications SpecificationsLimited Warranty and Liability

SMMC-3 specifications

Emerson SMMC-3 is a cutting-edge controller designed to enhance the efficiency and reliability of industrial automation processes. This smart motor management controller is specifically engineered to optimize the operation of motors and related systems, making it a crucial component in various industrial applications.

One of the standout features of the SMMC-3 is its advanced motor protection capabilities. It provides comprehensive protection against common motor faults such as overloads, phase failures, and short circuits. This ensures that the motors operate within safe parameters, thereby prolonging their lifespan and reducing maintenance costs. The SMMC-3 can be easily configured to meet specific application needs, making it versatile for a wide range of industries.

In addition to protection, the SMMC-3 offers real-time monitoring and diagnostics. It utilizes built-in sensing technologies to continuously monitor key motor parameters, including voltage, current, frequency, and temperature. This data is critical for predictive maintenance, allowing operators to anticipate potential issues before they escalate into costly downtime or equipment failure.

The SMMC-3 supports various communication protocols such as Modbus RTU and TCP, allowing for seamless integration into existing control systems. With its communication capabilities, users can easily access performance data remotely, facilitating better decision-making and resource management.

Another noteworthy characteristic of the SMMC-3 is its user-friendly interface. The device features an intuitive display and menu structure, making it straightforward for operators to configure settings, view performance metrics, and troubleshoot any issues. This ease of use significantly reduces training time and enhances overall operational efficiency.

Moreover, the SMMC-3 employs advanced algorithms and technologies for energy management. It helps in monitoring energy consumption, identifying inefficiencies, and providing recommendations for energy savings. This capability is increasingly important in today’s industrial environment, where reducing energy costs is a top priority.

In summary, Emerson SMMC-3 embodies state-of-the-art technologies and features that elevate motor management in industrial automation. With its robust protection mechanisms, real-time monitoring, versatile communication options, user-friendly design, and energy management capabilities, the SMMC-3 is an invaluable asset for industries striving for operational excellence and sustainability.