Fluke 199, 196, 192 Declaration of Conformity, Manufacturer, Statement of Conformity, Sample tests

Page 9

Unpacking the Test Tool Kit

Declaration of Conformity

for

Fluke 192/196/199

ScopeMeter® test tools

Manufacturer

Fluke Industrial B.V.

Lelyweg 1

7602 EA Almelo

The Netherlands

Statement of Conformity

Based on test results using appropriate standards,

the product is in conformity with

Electromagnetic Compatibility Directive 89/336/EEC

Low Voltage Directive 73/23/EEC

Sample tests

Standards used:

EN 61010.1 (1993)

Safety Requirements for Electrical Equipment for

Measurement, Control, and Laboratory Use

EN-IEC61326-1 (1997) Electrical equipment for measurements and laboratory use -EMC requirements-

The tests have been performed in a

typical configuration.

This Conformity is indicated by the symbol ,

i.e. “Conformité Européenne”.

1

Image 9

Contents Fluke 192/196/199 Page Limited Warranty & Limitation of Liability Service Centers Table of Contents Using The Recorder Functions Using The Multimeter Using Replay, Zoom and Cursors Fluke 192/196/199Iii Index SpecificationsManufacturer Declaration of ConformityStatement of Conformity Sample testsScopeMeter Test Tool Kit Unpacking the Test Tool Kit# Description DescriptionSafety Information Read First Safety Information Read First If Safety Features are Impaired Use of the test tool in a manner not specified mayImpair the protection provided by the equipment Using The Scope Powering the Test ToolAbout this Chapter Screen After Reset Resetting the Test ToolOpen the Waveform Options Navigating a MenuInput Connections Hiding Key Labels and MenusScope Connections Making Scope ConnectionsScreen After an Auto Set Displaying an Unknown Signal with Connect-and-ViewMaking Automatic Scope Measurements Select the Peak-PeakMeasurement Hz and V peak-peak as Scope Readings Freezing the ScreenUsing Average, Persistence and Glitch Capture Using Average for Smoothing WaveformsJump to Waveform Using Persistence to Display Waveforms Jump to Waveform and SelectPersistence , then select Infinite Suppressing High Frequency Noise Displaying GlitchesAcquiring Waveforms Selecting AC-CouplingReversing the Polarity of the Displayed Waveform Select 10kHz HF reject to Mathematics... to open Analyzing WaveformsMathematics menu Or a vs BMaking Meter Connections Using The MultimeterMeasuring Resistance Values Making Multimeter MeasurementsHighlight a ac Making a Current MeasurementOpen the Current Probe SubmenuAmpere Measurement Readings Selecting Auto/Manual Ranges Freezing the ReadingsMaking a Relative Measurement Making Relative MeasurementsOpening the Recorder Main Menu Using The Recorder FunctionsPlotting Measurements Over Time TrendPlot Starting a TrendPlot FunctionHighlight Trend Plot Scope TrendPlot Reading Displaying Recorded DataTurning Off the TrendPlot Display Changing the Recorder OptionsOpen the Recorder Options MenuRecording Scope Waveforms In Deep Memory Scope Record Starting a Scope Record FunctionHighlight Scope Record Using ScopeRecord in Single Sweep Mode Using Scope Record in Triggered Single Sweep Mode Jump to Display Glitches Select Yes, then jump to ModeLevel Triggered Single Sweep Recording Analyzing a TrendPlot or Scope RecordReplaying the 100 Most Recent Scope Screens Using Replay, Zoom and CursorsReplaying a Waveform Replaying Step-by-StepReplaying Continuously Turning Off the Replay FunctionCapturing 100 Intermittents Automatically Zooming in a Waveform Zooming in on a WaveformTurning Off the Zoom Function Displaying the Zoomed WaveformMaking Cursor Measurements Using Horizontal Cursors on a WaveformTurn off the cursors Using Vertical Cursors on a WaveformMaking Rise Time Measurements Using Cursors on a A+B, A-B or A*B WaveformTriggering on Waveforms Screen with all Trigger Information Setting Trigger Level and SlopeTrigger Delay or Pre-trigger View Using Trigger Delay or Pre-triggerAutomatic Trigger Options Open the Trigger Options menuOpen the Automatic Trigger Open the Trigger Options menu Open the Trigger on Edge menu Triggering on EdgesSelect Free Run, jump to Noise Reject FilterMaking a Single Acquisition Triggering on Noisy WaveformsSelect On Trigger, jump to Noise Set Noise reject Filter to OnMaking a Single Shot Measurement Triggering on External Waveforms Select 1.2V under the Ext LevelLabel Triggering on Video Signals Enable video line selection Triggering on Video FramesTriggering on Video Lines Triggering on Pulses Detecting Narrow PulsesSelect On Trigger Triggering on Narrow Glitches Open the Trigger Options menu Select On Trigger Finding Missing PulsesTriggering on Missing Pulses Saving and Recalling Using Memory, PC and PrinterSaving Screens with Associated Setups Deleting Screens with Associated Setups Recalling Screens with Associated SetupsDisplay the SAVE/PRINT key labels Scroll through all stored screens Recalling a Setup Configuration Viewing Stored ScreensDocumenting Screens Connecting to a ComputerConnecting a Serial Printer Connecting to a PrinterOpen the Printer Setup submenu Setting up the Printing ConfigurationPrinting a Screen Baud RateFluke 192/196/199 Tips Using the Standard AccessoriesHeavy Duty Fixed Connections for Scope Probing Using 2-mm Heavy Duty Test ProbesTips Using the Standard Accessories Measuring Using Independently Floating Isolated Inputs Using the Independently Floating Isolated InputsTips Using the Independently Floating Isolated Inputs Suppressing Key Labels and Menu’s Using the Tilt StandTurn the test tool off Press and holdChanging the Information Language Adjusting the Contrast and BrightnessOpen the Language Select Accept French as the languageChanging Date and Time Open Date Adjust menuChoose 1999, jump to Month Choose 04, jump to DaySetting the Power Down Timer Saving Battery LifeChanging the Auto Set Options Open the User Options menu Open the Auto Set Adjust MenuTo Coupling Select UnchangedCleaning the Test Tool Maintaining the Test ToolStoring the Test Tool Charging the Batteries Charging the BatteriesOpen the User Options menu Extending Battery Operation TimeCalibrating the Voltage Probes Replacing the NiMH Battery Pack BP190Select 101, then return Select Voltage, then jump toMaintaining the Test Tool Standard Accessories Parts and AccessoriesDisplaying Calibration Information Open the Version & CalibrationOrdering Code Standard AccessoriesTL24 General Purpose Leads RS200 Optional Accessories Troubleshooting FlukeView Does Not Recognize The Test Tool Battery Operated Fluke Accessories Do Not FunctionPerformance Characteristics SpecificationsSafety Characteristics IntroductionDual Input Oscilloscope Isolated Inputs a and B VerticalHorizontal Automatic Connect-and-View Trigger Trigger and DelayEdge Trigger Isolated External TriggerAutomatic Scope Measurements AC+DC Voltage True RMS AC Voltage VACPeak Amperes AMPFrequency Hz Duty Cycle DutyPhase PowerTemperature Temp Decibel dBDMM Measurements on Meter Inputs MeterDiode With Optional Temperature ProbeRecorder TrendPlot Meter or ScopeScope Record Miscellaneous Zoom, Replay and CursorsMemory Probe CalibrationOptical InterfacePort MechanicalEnvironmental Safety Max. Input VoltagesMax. Floating Voltage Electrical specifications SafetyProbe Environmental102 Disturbance less than 10% of full scale = 3V/m Electromagnetic Immunity104 Numerics Index106 107 108