Fluke 192, 199, 196 user manual Automatic Scope Measurements

Page 98

Fluke 192/196/199

Users Manual

Pulse Width Trigger

Screen Update

On Trigger, Single Shot

Trigger Conditions

<T, >T, T (±10 %), T(±10 %)

Source

A

Polarity

Positive or negative pulse

Pulse Time Adjustment Range

.......1/100 div. to 250 div.

 

with a maximum resolution of 50 ns.

Continuous Auto Set

Autoranging attenuators and time base, automatic Connect-and-View™ triggering with automatic source selection.

Modes

 

 

 

Normal

15

Hz to max. bandwidth

Low Frequency

1

Hz to max. bandwidth

Minimum Amplitude A and B

 

 

DC to 1 MHz

 

10 mV

1 MHz to max. bandwidth

20 mV

Automatic Capturing Scope Screens

Capacity

100 dual input scope Screens

For viewing screens, see Replay function.

Automatic Scope Measurements

The accuracy of all readings is within ± (% of reading + number of counts) from 18 °C to 28 °C. Add 0.1x (specific accuracy) for each °C below 18 °C or above 28 °C. For voltage measurements with 10:1 probe, add probe accuracy unless the probe has been calibrated on the test tool. At least 1.5 waveform period must be visible on the screen.

General

Inputs

A and B

DC Common Mode Rejection (CMRR)

>100 dB

AC Common Mode Rejection at 50, 60, or 400 Hz

......>60 dB

DC Voltage (VDC)

 

 

Maximum Voltage

 

 

with 10:1 probe

1000 V

direct (1:1)

300 V

Maximum Resolution

 

 

with 10:1 probe

1 mV

direct (1:1)

100 µV

Full Scale Reading

1100 counts

Accuracy at 5 s to 5 s/div

±(1.5 % +5 counts)

Normal Mode AC Rejection at 50 or 60 Hz

>60 dB

90

Image 98
Contents Fluke 192/196/199 Page Limited Warranty & Limitation of Liability Service Centers Table of Contents Using Replay, Zoom and Cursors Using The MultimeterUsing The Recorder Functions Fluke 192/196/199Iii Specifications IndexStatement of Conformity Declaration of ConformityManufacturer Sample testsUnpacking the Test Tool Kit ScopeMeter Test Tool KitDescription # DescriptionSafety Information Read First Safety Information Read First Impair the protection provided by the equipment If Safety Features are ImpairedUse of the test tool in a manner not specified may About this Chapter Using The ScopePowering the Test Tool Resetting the Test Tool Screen After ResetNavigating a Menu Open the Waveform OptionsHiding Key Labels and Menus Input ConnectionsMaking Scope Connections Scope ConnectionsDisplaying an Unknown Signal with Connect-and-View Screen After an Auto SetMeasurement Making Automatic Scope MeasurementsSelect the Peak-Peak Freezing the Screen Hz and V peak-peak as Scope ReadingsJump to Waveform Using Average, Persistence and Glitch CaptureUsing Average for Smoothing Waveforms Persistence , then select Infinite Using Persistence to Display WaveformsJump to Waveform and Select Displaying Glitches Suppressing High Frequency NoiseReversing the Polarity of the Displayed Waveform Acquiring WaveformsSelecting AC-Coupling Select 10kHz HF reject to Mathematics menu Analyzing WaveformsMathematics... to open Or a vs BUsing The Multimeter Making Meter ConnectionsMaking Multimeter Measurements Measuring Resistance ValuesOpen the Current Probe Making a Current MeasurementHighlight a ac SubmenuAmpere Measurement Readings Freezing the Readings Selecting Auto/Manual RangesMaking Relative Measurements Making a Relative MeasurementUsing The Recorder Functions Opening the Recorder Main MenuHighlight Trend Plot Scope Plotting Measurements Over Time TrendPlotStarting a TrendPlot Function Displaying Recorded Data TrendPlot ReadingOpen the Recorder Options Changing the Recorder OptionsTurning Off the TrendPlot Display MenuHighlight Scope Record Recording Scope Waveforms In Deep Memory Scope RecordStarting a Scope Record Function Using ScopeRecord in Single Sweep Mode Level Using Scope Record in Triggered Single Sweep ModeJump to Display Glitches Select Yes, then jump to Mode Analyzing a TrendPlot or Scope Record Triggered Single Sweep RecordingUsing Replay, Zoom and Cursors Replaying the 100 Most Recent Scope ScreensReplaying Step-by-Step Replaying a WaveformCapturing 100 Intermittents Automatically Replaying ContinuouslyTurning Off the Replay Function Zooming in on a Waveform Zooming in a WaveformDisplaying the Zoomed Waveform Turning Off the Zoom FunctionUsing Horizontal Cursors on a Waveform Making Cursor MeasurementsUsing Vertical Cursors on a Waveform Turn off the cursorsUsing Cursors on a A+B, A-B or A*B Waveform Making Rise Time MeasurementsTriggering on Waveforms Setting Trigger Level and Slope Screen with all Trigger InformationUsing Trigger Delay or Pre-trigger Trigger Delay or Pre-trigger ViewOpen the Automatic Trigger Automatic Trigger OptionsOpen the Trigger Options menu Select Free Run, jump to Noise Triggering on EdgesOpen the Trigger Options menu Open the Trigger on Edge menu Reject FilterSelect On Trigger, jump to Noise Triggering on Noisy WaveformsMaking a Single Acquisition Set Noise reject Filter to OnMaking a Single Shot Measurement Label Triggering on External WaveformsSelect 1.2V under the Ext Level Triggering on Video Signals Triggering on Video Lines Enable video line selectionTriggering on Video Frames Select On Trigger Triggering on PulsesDetecting Narrow Pulses Triggering on Narrow Glitches Finding Missing Pulses Open the Trigger Options menu Select On TriggerTriggering on Missing Pulses Using Memory, PC and Printer Saving and RecallingSaving Screens with Associated Setups Display the SAVE/PRINT key labels Deleting Screens with Associated SetupsRecalling Screens with Associated Setups Recalling a Setup Configuration Viewing Stored Screens Scroll through all stored screensConnecting to a Computer Documenting ScreensConnecting to a Printer Connecting a Serial PrinterPrinting a Screen Setting up the Printing ConfigurationOpen the Printer Setup submenu Baud RateFluke 192/196/199 Using the Standard Accessories TipsProbing Using 2-mm Heavy Duty Test Probes Heavy Duty Fixed Connections for ScopeTips Using the Standard Accessories Using the Independently Floating Isolated Inputs Measuring Using Independently Floating Isolated InputsTips Using the Independently Floating Isolated Inputs Turn the test tool off Using the Tilt StandSuppressing Key Labels and Menu’s Press and holdOpen the Language Select Adjusting the Contrast and BrightnessChanging the Information Language Accept French as the languageChoose 1999, jump to Month Open Date Adjust menuChanging Date and Time Choose 04, jump to DaySaving Battery Life Setting the Power Down TimerTo Coupling Open the User Options menu Open the Auto Set Adjust MenuChanging the Auto Set Options Select UnchangedStoring the Test Tool Cleaning the Test ToolMaintaining the Test Tool Charging the Batteries Charging the BatteriesExtending Battery Operation Time Open the User Options menuSelect 101, then return Replacing the NiMH Battery Pack BP190Calibrating the Voltage Probes Select Voltage, then jump toMaintaining the Test Tool Displaying Calibration Information Parts and AccessoriesStandard Accessories Open the Version & CalibrationStandard Accessories Ordering CodeTL24 General Purpose Leads RS200 Optional Accessories Troubleshooting Battery Operated Fluke Accessories Do Not Function FlukeView Does Not Recognize The Test ToolSafety Characteristics SpecificationsPerformance Characteristics IntroductionHorizontal Dual Input OscilloscopeIsolated Inputs a and B Vertical Edge Trigger Trigger and DelayAutomatic Connect-and-View Trigger Isolated External TriggerAutomatic Scope Measurements AC Voltage VAC AC+DC Voltage True RMSFrequency Hz Amperes AMPPeak Duty Cycle DutyTemperature Temp PowerPhase Decibel dBMeter DMM Measurements on Meter InputsWith Optional Temperature Probe DiodeScope Record RecorderTrendPlot Meter or Scope Zoom, Replay and Cursors MiscellaneousOptical InterfacePort Probe CalibrationMemory MechanicalEnvironmental Max. Floating Voltage SafetyMax. Input Voltages Probe SafetyElectrical specifications Environmental102 Electromagnetic Immunity Disturbance less than 10% of full scale = 3V/m104 Index Numerics106 107 108