Pioneer VSA-AX10Ai manual Replacing the lithium-ion batteries

Page 11

Before you start

01

2 Remove the battery cover.

3Use a pen or other sharp instrument to press the reset button located in the hole to the right (above the battery).

After restarting the remote control, the touch screen shows the Home menu.

Replacing the lithium-ion batteries

If you notice that the remote will no longer hold a charge, you may need to replace the lithium-ion battery cells.

Caution

•The lithium-ion batteries may present a fire or chemical burn hazard if misused. Do not disassemble, heat above 100˚C (212˚F), or incinerate.

•Replacement cells must be of type AZW7264, manufactured by NEC TOKIN Corporation. Use of any other battery cells may result in fire or explosion. Contact the Pioneer Service Center specified on your warranty card to obtain new batteries. Replacement cells are not covered under warranty.

•Dispose of used battery cells immediately after replacement. Keep away from children.

•When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country or area.

1Use a small phillips screwdriver to remove the screw fixing the battery cover to the back of the remote.

2 Remove the battery cover.

3Disconnect the old battery cell from the unit. Do not pull the connector out by holding onto the attached wires. Hold the connector firmly with your fingers, or use a small screwdriver (or other sharp tool) to disconnect it.

4Connect the new battery cell.

Push the connector in until it is fully inserted. Make sure you keep the wire out of the way and line up the cell properly so that the battery cover can be closed easily.

11

En

Page 10 Page 12
Image 11
Page 10 Page 12
Contents VSA-AX10Ai Risk of Electric Shock Do not Open Operating EnvironmentPage Contents Additional information Using other functionsAdvanced setup Other connectionsOur philosophy FeaturesBefore you start Chapter Checking the supplied accessoriesUsing the remote control Before you startPress Calibrate Setting up the remote controlCalibrating the remote control screen Before you startSetting the time-out setting Setting the clockSetting the button alert volume Press Reset to Default Resetting the remote controlLocking the remote control Restarting the remote controlReplacing the lithium-ion batteries Rear panel Connecting your equipmentConnecting your equipment Chapter When making cable connections Connecting your equipmentConnecting your equipment Connecting your TV DVD player Connecting your equipment Connecting a DVD playerConnecting the multichannel analog outputs STB VSA-AX10Ai Connecting your equipment Connecting a VCR or DVD recorderConnecting your equipment Connecting other video sources About the video converter Connecting your equipment Using the component video jacksConnecting your equipment Connecting digital audio sources Connecting your equipment Connecting analog audio sources Portable DVD player, etc Connecting the speakers Connecting your equipment Installing your speaker systemPlacing the speakers Bare wire connectionsAbout the AC outlet Connecting your equipment Plugging in the amplifierDisplay Controls and displaysControls and displays Chapter Controls and displays Tone Home menu screens Controls and displays Remote controlBasic remote control displays Digital NR SetupAmplifier menu screens TV control menu screens Remote control displays for other componentsOperating menus for additional components TOP Menu Search ModeAudio SubtitleGetting started Chapter Automatically setting up for surround soundSwitch on the amplifier and your TV Getting startedEnter Getting startedPlaying a source Checking the settings on your DVD or other playerOther problems when using the Auto Surround Setup Change the amplifier input to the source you want to play Listening in surround sound Listening to your systemListening to your system Chapter About the listening modesListening to your system Dolby Pro Logic IIx Music settingsNeo6 Music settings Use the Option +/- buttons to adjust the effect level Using the Advanced surround effectsUsing the Home THX modes Adjusting the Advanced Surround effect levelPRO Logic NEO6 Cinema Listening with headphonesListening in stereo Pro Logic IIx MoviePress Multi CH Input on the remote control Home menu screen Using the Stream Direct modeAnalog Selecting the input signal typeChannel Listening to high-sampling formatsSelecting USB and multichannel analog input channels Surround back channel options Listening to your system Using the surround back channelPress SB CH Mode repeatedly to cycle through AutoVSB Auto VSB on VSB OFF Use the Option +/- buttons to change the settingCreating a center speaker effect Switching the tone control on or off Listening to your system Using Hi-bit and Hi-samplingUsing Midnight and Loudness listening Using the tone controlTreble Adjusting the bass and trebleReducing noise during playback Listening to your system Listening to dual mono soundtracks Select ‘Surround Setup’ then press Enter Surround Setup menuSurround Setup menu Chapter Making amplifier settings from the Surround Setup menuSpeaker Systems Surround Setup menuLarge Select ‘Channel Level’ then press Enter Channel LevelAcoustic Calibration EQ Setting the Acoustic Calibration EQ automaticallySetting the Acoustic Calibration EQ manually Speaker DistanceSelect ‘Data Copy’ then press Enter Copying your Acoustic Calibration EQ settingsSelect ‘Manual’ then press Enter Select CUSTOM1 or CUSTOM2 then press EnterProfessional Acoustic Calibration EQ How to use Professional Acoustic Calibration EQHow to interpret the graphical output If you selected ‘Auto Pro.’, select ‘Start’ and press Using Professional Acoustic Calibration EQSelect a manual setup option and press Enter Select ‘Professional’ then press EnterSelect ‘X-Curve’ then press Enter Switch the X-Curve on or OFFCurve Use Cursor left/right buttons to selectCycle through the settings screen by screen Checking your surround settingsSelect ‘Check’ from the Surround Setup menu and press Enter Controlling other equipment Chapter Using the remote control with other componentsRecalling preset codes Controlling other equipmentControlling other equipment Select a setting typePioneer-1 DVR-7000 Programming signals from other remote controlsPress Learning on the remote setup menu Press KEY Label on the remote setup menu Editing remote control button namesPress Direct Function on the remote setup menu Press OK to confirm the settingsChoose how you want to change the look of the button Press OK when you’ve finishedSelect the button you want to rename Programming a multi operation or a shutdown sequence Controlling other equipment Multi Operation and System OffMulti Operation Using multi operationsPress OK when you’re finished From the remote control Home menu pressSystem OFF Switching components on and offUsing the 12 volt trigger Using System offMonitoring your recording Using other functionsUsing other functions Chapter Making an audio or a video recordingWatching video and audio sources independently Adjusting the delay of a soundtrackUse the Option +/- buttons to adjust the amount of delay Enhancing Sacd playback Using other functionsSwitch the SD1 Normal Stream Direct mode Switching the speaker impedance Using other functions Dimming the displayDefault amplifier settings Using other functions Checking your system settingsResetting the system Bypass Other connections Using speaker system BSwitching the speaker system Using speaker system B in another roomSP B ITU-R is selected Select the ‘ITU-R’ setting from the Speaker Systems menuOther connections Bi-amping your front speakersConnecting additional amplifiers Bi-wiring your speakersUsing the pre-outs Connecting an external stereo pre-amplifier Using the i.LINK interfaceCreating an i.LINK network About i.LINKAbout Pqls rate control Press ‘USB’ on the remote control Home menu Screen Using the USB interfaceConnecting a PC for Advanced Mcacc output Select ‘PC Output’ and press Enter Advanced Mcacc output using your PCAssigning the digital inputs Advanced setupAdvanced setup Chapter Input Assign menuAssigning the i.LINK inputs Advanced setupAssigning the component video inputs Multi in OFF USB OFF Expert Setup menuSelect ‘Expert Setup’ then press Enter Assigning the video inputsBass Peak Level OSD AdjustmentEdit the name as necessary and press Enter Dynamic Range ControlFunction Rename OSD OverlayVolt Trigger THX Audio SetupSelect ‘THX Audio Setup’ then press Enter Surround Back Speaker Position THX Ultra2 Subwoofer SetupAdditional information Chapter Optimizing your speaker setupBasic surround setup Additional informationAdditional information THX speaker system setupNo sound Additional information TroubleshootingPower Listening in surround sound on Cause Remedy Other audio problemsAudio sources on VideoRemote control SettingsThis unit’s sensor on DisplayLink messages Link interfaceMiscellaneous USB interfaceDolby Additional information Surround sound formatsPCM Pulse Code Modulation About THXWindows Media Audio 9 Professional THX MusicMode Maintenance of external surfacesTHX Ultra2 Cinema mode Advanced Speaker Array ASAAdditional information Specifications 04B00001 ARB7291-A

VSA-AX10Ai specifications

The Pioneer VSA-AX10Ai is a high-end, multi-channel home theater receiver that stands out for its robust performance and cutting-edge technologies. Launched as a flagship model, it combines advanced audio processing capabilities with a formidable power output, catering to both audiophiles and home theater enthusiasts.

One of the standout features of the VSA-AX10Ai is its Direct Energy HD Amplification technology, which incorporates a Class D amplifier design. This technology not only ensures high power efficiency but also minimizes distortion, delivering pristine sound quality at high volumes. The receiver boasts a substantial output of 200 watts per channel over eight channels, making it an ideal choice for driving large, demanding speaker systems.

In terms of audio decoding, the VSA-AX10Ai supports a multitude of formats, including Dolby TrueHD and DTS-HD Master Audio. This feature allows the receiver to provide a cinematic surround sound experience, ensuring that every detail of the soundtrack is delivered with accuracy and clarity. The device is also equipped with a high-quality 24-bit/192 kHz DAC, assuring top-notch sound reproduction from a variety of sources.

The VSA-AX10Ai features Pioneer’s sophisticated MCACC (Multi-Channel Acoustic Calibration System), which automatically calibrates the audio output to match the room's acoustics. By measuring sound from each speaker and adjusting levels, delays, and equalization, it ensures a balanced sound field, regardless of room shape or speaker placement.

Connectivity is extensive, with multiple HDMI inputs offering 4K pass-through and upscaling capabilities. This makes the receiver well-suited for modern home theater setups that require integration with 4K Ultra HD displays. It also includes legacy inputs, ensuring compatibility with older audio and video equipment.

Another noteworthy characteristic is the receiver’s build quality. The VSA-AX10Ai features a rigid chassis designed to minimize vibration as well as a premium-grade power supply, which contributes to its overall reliability and performance.

Overall, the Pioneer VSA-AX10Ai encapsulates the essence of high-fidelity home audio and video. With its extensive feature set, exceptional sound quality, and robust performance capabilities, it remains a top choice for those seeking a comprehensive and immersive home theater experience. Whether for music playback or movie watching, this receiver delivers an unparalleled audio experience that stands the test of time.
Top Page Image Contents