Pioneer VSA-AX10Ai manual Settings, Remote control

Page 96

11Additional information

Settings

Symptom

Cause

Remedy

The Auto Surround Setup

• The ambient noise level in the room is too

continually shows an error.

high.

•Keep the noise level in the room as low as possible when using the Auto Surround Setup. If the noise cannot be kept low enough, you will have to set up the surround sound manually (page 51).

After using the Auto Surround Setup, the subwoofer distance setting is set further than the actual measured distance.

•The low-pass filter found in subwoofers can introduce a delay in the playback sound.

•This is not a malfunction. The Auto Surround Setup has compensated for the delay caused by the filter.

After using the Auto Surround Setup, the speaker size setting (LARGE or SMALL) is incorrect.

•There was some inaudible low-frequency noise in the room.

•The low-frequency noise could have been caused by an air conditioner or motor. Switch off all appliances in the room and rerun the Auto Surround Setup.

Remote control

Symptom

Cause

Remedy

The amplifier cannot be remote controlled.

• You are too far away or at a bad angle for

• Operate within 7 m, 30° of the remote sensor on the

operation.

front panel (see Using the remote control on page 7).

 

 

• There is an obstacle between the amplifier

• Remove the obstacle or operate from another angle of

and the remote control.

position.

 

 

• Strong light such as fluorescent light.

• Avoid exposing the remote sensor on the front panel to

 

direct light.

• The remote control has a weak charge.

•Recharge the remote control (see Recharging the remote control on page 7). You can also use the remote while it’s placed on the recharger.

• The remote control is locked.

•Unlock the remote control (see Locking the remote control on page 10).

• The CONTROL IN jack has been hooked up. • Disconnect the CONTROL IN jack (see Operating other

 

 

Pioneer components with this unit’s sensor on page 68).

 

 

 

Other components cannot be

• The proper code hasn't been input into the

• Input the proper code into the remote control (see

remote controlled.

remote control to control that component.

page 61).

 

 

 

 

• Something is plugged into the CONTROL IN

• Either point remote at the remote sensor of the unit that

 

jack.

is plugged into the CONTROL IN jack or unplug the cable

 

 

from the CONTROL IN jack and use remote normally (see

 

 

Operating other Pioneer components with this unit’s

 

 

sensor on page 68).

 

 

 

The remote control doesn’t seem

• The remote control hasn’t been seated

• Reseat it on the recharger, making sure to align the

to recharge properly (the

properly on the recharger.

indent on the bottom of the remote with the tabs on the

recharge indicator doesn’t light),

 

recharger.

or it won’t hold a charge.

 

 

• The battery cells need to be replaced.

• See Replacing the lithium-ion batteries on page 11.

 

 

 

 

The remote control display is

• The remote control needs to be recharged.

• Place the remote control on the recharger. If the remote

flashing LOW BATTERY or is

 

hasn’t been charged for awhile, the remote control display

blank.

 

may remain blank for several minutes before the touch

 

 

screen appears. See Recharging the remote control on

 

 

page 7 for more on this.

 

 

 

The remote control display is

• The remote control contrast needs to be

• Use the contrast control on the right-hand side of the

blank or very hard to see.

adjusted.

remote to adjust the contrast as necessary.

 

 

 

 

• The remote control backlight is switched on

• Switch the backlight off.

 

in a bright room.

 

 

 

 

When you press an input select

• The Direct Function feature for the

• See Remote Direct function on page 64 to switch it on

button on the Home menu

component you want to select is switched off. again.

screen, the amplifier input

 

 

source doesn’t change to the selected function.

Can’t program certain buttons with remote signals when using the learning feature.

• You have selected a button that cannot

• Select another button that can learn commands (see

learn commands.

Programming signals from other remote controls on

 

page 63).

 

 

• You have already selected a button for

• Press the same button again to deselect it or press END

learning.

to go back a screen (see Programming signals from other

 

remote controls on page 63).

96

En

Page 95 Page 97
Image 96
Page 95 Page 97
Contents VSA-AX10Ai Operating Environment Risk of Electric Shock Do not OpenPage Contents Using other functions Advanced setupOther connections Additional informationFeatures Our philosophyChecking the supplied accessories Using the remote controlBefore you start Before you start ChapterSetting up the remote control Calibrating the remote control screenBefore you start Press CalibrateSetting the clock Setting the button alert volumeSetting the time-out setting Resetting the remote control Locking the remote controlRestarting the remote control Press Reset to DefaultReplacing the lithium-ion batteries Connecting your equipment Connecting your equipment ChapterRear panel Connecting your equipment When making cable connectionsConnecting your equipment Connecting your TV Connecting your equipment Connecting a DVD player DVD playerConnecting the multichannel analog outputs STB Connecting your equipment Connecting a VCR or DVD recorder VSA-AX10AiConnecting your equipment Connecting other video sources Connecting your equipment Using the component video jacks About the video converterConnecting your equipment Connecting digital audio sources Connecting your equipment Connecting analog audio sources Portable DVD player, etc Connecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersConnecting your equipment Plugging in the amplifier About the AC outletControls and displays Controls and displays ChapterDisplay Controls and displays Tone Controls and displays Remote control Basic remote control displaysHome menu screens Setup Amplifier menu screensDigital NR Remote control displays for other components TV control menu screensOperating menus for additional components Search Mode AudioSubtitle TOP MenuAutomatically setting up for surround sound Switch on the amplifier and your TVGetting started Getting started ChapterGetting started EnterChecking the settings on your DVD or other player Other problems when using the Auto Surround SetupPlaying a source Change the amplifier input to the source you want to play Listening to your system Listening to your system ChapterAbout the listening modes Listening in surround soundDolby Pro Logic IIx Music settings Neo6 Music settingsListening to your system Using the Advanced surround effects Using the Home THX modesAdjusting the Advanced Surround effect level Use the Option +/- buttons to adjust the effect levelListening with headphones Listening in stereoPro Logic IIx Movie PRO Logic NEO6 CinemaUsing the Stream Direct mode Press Multi CH Input on the remote control Home menu screenSelecting the input signal type AnalogListening to high-sampling formats Selecting USB and multichannel analog input channelsChannel Listening to your system Using the surround back channel Press SB CH Mode repeatedly to cycle throughAuto Surround back channel optionsUse the Option +/- buttons to change the setting Creating a center speaker effectVSB Auto VSB on VSB OFF Listening to your system Using Hi-bit and Hi-sampling Using Midnight and Loudness listeningUsing the tone control Switching the tone control on or offAdjusting the bass and treble Reducing noise during playbackTreble Listening to your system Listening to dual mono soundtracks Surround Setup menu Surround Setup menu ChapterMaking amplifier settings from the Surround Setup menu Select ‘Surround Setup’ then press EnterSurround Setup menu Speaker SystemsLarge Channel Level Select ‘Channel Level’ then press EnterSetting the Acoustic Calibration EQ automatically Setting the Acoustic Calibration EQ manuallySpeaker Distance Acoustic Calibration EQCopying your Acoustic Calibration EQ settings Select ‘Manual’ then press EnterSelect CUSTOM1 or CUSTOM2 then press Enter Select ‘Data Copy’ then press EnterHow to use Professional Acoustic Calibration EQ How to interpret the graphical outputProfessional Acoustic Calibration EQ Using Professional Acoustic Calibration EQ Select a manual setup option and press EnterSelect ‘Professional’ then press Enter If you selected ‘Auto Pro.’, select ‘Start’ and pressSwitch the X-Curve on or OFF CurveUse Cursor left/right buttons to select Select ‘X-Curve’ then press EnterChecking your surround settings Select ‘Check’ from the Surround Setup menu and press EnterCycle through the settings screen by screen Using the remote control with other components Recalling preset codesControlling other equipment Controlling other equipment ChapterSelect a setting type Controlling other equipmentProgramming signals from other remote controls Press Learning on the remote setup menuPioneer-1 DVR-7000 Editing remote control button names Press Direct Function on the remote setup menuPress OK to confirm the settings Press KEY Label on the remote setup menuPress OK when you’ve finished Select the button you want to renameChoose how you want to change the look of the button Controlling other equipment Multi Operation and System Off Programming a multi operation or a shutdown sequenceUsing multi operations Press OK when you’re finishedFrom the remote control Home menu press Multi OperationSwitching components on and off Using the 12 volt triggerUsing System off System OFFUsing other functions Using other functions ChapterMaking an audio or a video recording Monitoring your recordingAdjusting the delay of a soundtrack Use the Option +/- buttons to adjust the amount of delayWatching video and audio sources independently Using other functions Switch the SD1 Normal Stream Direct modeEnhancing Sacd playback Using other functions Dimming the display Switching the speaker impedanceUsing other functions Checking your system settings Resetting the systemDefault amplifier settings Bypass Using speaker system B Switching the speaker systemUsing speaker system B in another room Other connectionsSelect the ‘ITU-R’ setting from the Speaker Systems menu Other connectionsBi-amping your front speakers SP B ITU-R is selectedBi-wiring your speakers Using the pre-outsConnecting additional amplifiers Using the i.LINK interface Connecting an external stereo pre-amplifierAbout i.LINK About Pqls rate controlCreating an i.LINK network Using the USB interface Press ‘USB’ on the remote control Home menu ScreenConnecting a PC for Advanced Mcacc output Advanced Mcacc output using your PC Select ‘PC Output’ and press EnterAdvanced setup Advanced setup ChapterInput Assign menu Assigning the digital inputsAdvanced setup Assigning the component video inputsAssigning the i.LINK inputs Expert Setup menu Select ‘Expert Setup’ then press EnterAssigning the video inputs Multi in OFF USB OFFOSD Adjustment Bass Peak LevelDynamic Range Control Function RenameOSD Overlay Edit the name as necessary and press EnterTHX Audio Setup Select ‘THX Audio Setup’ then press EnterVolt Trigger THX Ultra2 Subwoofer Setup Surround Back Speaker PositionOptimizing your speaker setup Basic surround setupAdditional information Additional information ChapterTHX speaker system setup Additional informationAdditional information Troubleshooting PowerNo sound Listening in surround sound on Other audio problems Cause RemedyVideo Audio sources onSettings Remote controlDisplay This unit’s sensor onLink interface Link messagesUSB interface MiscellaneousAdditional information Surround sound formats DolbyAbout THX Windows Media Audio 9 ProfessionalPCM Pulse Code Modulation Maintenance of external surfaces THX Ultra2 Cinema modeAdvanced Speaker Array ASA THX MusicModeAdditional information Specifications 04B00001 ARB7291-A

VSA-AX10Ai specifications

The Pioneer VSA-AX10Ai is a high-end, multi-channel home theater receiver that stands out for its robust performance and cutting-edge technologies. Launched as a flagship model, it combines advanced audio processing capabilities with a formidable power output, catering to both audiophiles and home theater enthusiasts.

One of the standout features of the VSA-AX10Ai is its Direct Energy HD Amplification technology, which incorporates a Class D amplifier design. This technology not only ensures high power efficiency but also minimizes distortion, delivering pristine sound quality at high volumes. The receiver boasts a substantial output of 200 watts per channel over eight channels, making it an ideal choice for driving large, demanding speaker systems.

In terms of audio decoding, the VSA-AX10Ai supports a multitude of formats, including Dolby TrueHD and DTS-HD Master Audio. This feature allows the receiver to provide a cinematic surround sound experience, ensuring that every detail of the soundtrack is delivered with accuracy and clarity. The device is also equipped with a high-quality 24-bit/192 kHz DAC, assuring top-notch sound reproduction from a variety of sources.

The VSA-AX10Ai features Pioneer’s sophisticated MCACC (Multi-Channel Acoustic Calibration System), which automatically calibrates the audio output to match the room's acoustics. By measuring sound from each speaker and adjusting levels, delays, and equalization, it ensures a balanced sound field, regardless of room shape or speaker placement.

Connectivity is extensive, with multiple HDMI inputs offering 4K pass-through and upscaling capabilities. This makes the receiver well-suited for modern home theater setups that require integration with 4K Ultra HD displays. It also includes legacy inputs, ensuring compatibility with older audio and video equipment.

Another noteworthy characteristic is the receiver’s build quality. The VSA-AX10Ai features a rigid chassis designed to minimize vibration as well as a premium-grade power supply, which contributes to its overall reliability and performance.

Overall, the Pioneer VSA-AX10Ai encapsulates the essence of high-fidelity home audio and video. With its extensive feature set, exceptional sound quality, and robust performance capabilities, it remains a top choice for those seeking a comprehensive and immersive home theater experience. Whether for music playback or movie watching, this receiver delivers an unparalleled audio experience that stands the test of time.
Top Page Image Contents