Cobra Electronics MR HH330 FLT EU owner manual Memory Location Mode, Tri-Watch channel

Page 15

Operating Your Radio

Channel Up/Down Button

TRI-WATCH Button

Tri-Watch Scan Mode

Advanced Operation

2.Press Channel Up/Down button to select the desired

Tri-Watch channel.

3.Press and release TRI-WATCHbutton or Call/Enter/Setup button to confirm entry.

4.Repeat steps 2 and 3 to program the remaining additional Tri-Watchmemory channel.

5.After programming both Tri-Watchmemory channels the radio will immediately engage

Tri-Watch mode.

Using Tri-Watch

Tri-Watch Scan Mode:

1.From Marine Standby mode, press the TRI-WATCHbutton. The TRI icon will appear on the LCD display and the radio will scan through the three (3) Tri-Watchmemory channels.

2.A signal on any one (1) of the three (3) channels will stop the scan for 10 seconds to allow you to listen to the traffic on that location.

NOTE

After the Tri-Watchscan stops to monitor a channel, as long as you do not press any buttons within 10 seconds, your radio will automatically resume scanning the Tri-Watchchannels.

3.Press the Channel Up/Down button to resume scanning the Tri-Watchchannels or to change the scan direction.

4.To EXIT the Tri-Watchscan, press the TRI-WATCHbutton again. The TRI icon will disappear from the LCD and the radio will return to Marine Standby mode.

Operating Your Radio

MEM/ESC Button

Memory Location Number

Channel Up/Down Buttons

Channel Number

Advanced Operation

Memory Location Mode

Your radio has unlimited memory locations for storing your most frequently used channels. These memory locations can be selected individually or can be scanned. (See page 28 under Memory Location Scan.)

To enter Memory mode, press MEM/ESC button. The display will show the MEM icon and the Memory Channel bank will be activated and displayed.

To Program Memory Locations:

1.Press and hold the MEM/ESC button for two (2) seconds. The memory location number will start flashing and the MEM icon will be turned On.

2.Use the Channel Up/Down button to advance to the memory location (00-99) you want to program.

3.Press the MEM/ESC button to select the memory location. The memory channel number will stop flashing and the channel number will start flashing.

4.Use the Channel Up/Down button to change to the channel you want to store into the selected memory location.

5.Press the MEM/ESC button to program that channel. The memory location number will flash again.

Repeat steps 2 through 5 to program as many additional memories as you want.

6.Press and hold the MEM/ESC button for two (2) seconds. This will return the radio to Memory mode.

7.Press and release the MEM/ESC button again to return to Marine Standby mode.

 

 

 

 

24 English

Nothing Comes Close to a Cobra® 25

Page 14 Page 16
Image 15
Page 14 Page 16
Contents For Warranty, Product Service Accessory Information Our Thanks to You Customer AssistanceCustomer Assistance Backlit LCD Liquid Crystal Display Screen Radio Controls IndicatorsBacklit LCD Screen Product Features Product FeaturesTable of Contents Important Safety Information General PrecautionsImportant Safety Information Licensing Information Recommendations for Marine CommunicationBelt Clip Included in this PackageWrist Strap and Belt Clip Wrist StrapBatteries and Charger Installing the Battery PackBatteries and Charger Initial ChargeTo Remove Battery Pack from Radio Maintaining the Battery ChargeAlkaline Batteries Radio Speaker and Microphone Getting StartedCommon Radio Functions Getting StartedChannel Up/Down Buttons Backlight/Key Lock ButtonTo Display the Backlight Momentarily Key LockTo Toggle Between H-M-L Power Modes Setup Mode ProgrammingSetup Mode Programming High/Medium/Low H-M-L Power ButtonTo Set Channel Map Operating Area Squelch ControlTo Set Squelch Control International/Canada/USA Channel MapsAtis ID Programming Atis ID ProgrammingStandby/Receive Transmit Marine Standby and Receive Rx ModeChannel 16 Mode Tri-Watch ModeTri-Watch channel Memory Location ModeTri-Watch mode Using Tri-Watch Tri-Watch Scan Mode Press Channel Up/Down button to select the desiredTo Erase Stored Memory Locations Channel Scan ModeTo Exit Memory Location Mode To Recall a Stored Memory LocationFloating Radio Floating FeatureMemory Location Scan Mode Burp FeatureMaintenance and Troubleshooting VHF Marine Radio Procedures Radiotelephone Calls Emergency Messages and Distress ProcedureVoice Calling Voice CallingIf You Hear a Distress Call Emergency Messages Distress ProcedureMarine Emergency Signals Marine Distress ProcedureFrequency Range Tx 156.025 to 157.425 MHz RF Output Power Emergency Messages and Distress ProcedureSpecifications SpecificationsVHF Marine Channel Assignments Accessories05A 01A03A 04A21A 18A19A 20A66A 63A64A 65A83A 80A81A 82ADeclaration of Conformity and CE Markings Declaration of ConformityCE Marking
Top Page Image Contents