Icom IC-F3062T, IC-F3061T, IC-F3062S, IC-F3061S, IC-F3063S, IC-F3063T service manual Introduction

Page 2

INTRODUCTION

This service manual describes the latest service information for the IC-F3061T/S,IC-F3062T/S and IC-F3063T/SVHF TRANSCEIVER at the time of publication.

MODEL

VERSION

SYMBOL

CHANNEL SPACING

KEY PAD

IC-F3061T

U.S.A

[USA-01]

15.0 kHz/30.0 kHz

10-key

IC-F3061S

4-key

 

 

 

IC-F3062T

EURO

[EUR-01]

12.5 kHz/25.0 kHz

10-key

IC-F3062S

4-key

 

 

 

IC-F3063T

GENERAL

[GEN-01]

12.5 kHz/20.0 kHz

10-key

IC-F3063S

/25.0 kHz

4-key

 

 

To upgrade quality, all electrical or mechanical parts and internal circuits are subject to change without notice or obligation.

DANGER

NEVER connect the transceiver to an AC outlet or to a DC power supply that uses more than 7.2 V. Such a connection could cause a fire or electric hazard.

DO NOT expose the transceiver to rain, snow or any liquids.

DO NOT reverse the polarities of the power supply when connecting the transceiver.

DO NOT apply an RF signal of more than 20 dBm (100 mW) to the antenna connector. This could damage the trans- ceiver's front end.

ORDERING PARTS

Be sure to include the following four points when ordering replacement parts:

1.10-digit Icom parts number

2.Component name and informations

3.Equipment model name and unit name

4.Quantity required

<SAMPLE ORDER>

5030002830

LCD

M4-0078TAY-2

IC-F3061T

Front unit

5 pieces

8810009220

Screw

PH B0 M28 ZK (BT) IC-F3061T

Chassis

10 pieces

Addresses are provided on the inside back cover for your convenience.

REPAIR NOTES

1.Make sure the problem is internal before disassembling the transceiver.

2.DO NOT open the transceiver until the transceiver is disconnected from its power source.

3.DO NOT force any of the variable components. Turn them slowly and smoothly.

4.DO NOT short any circuits or electronic parts. An insulated turning tool MUST be used for all adjustments.

5.DO NOT keep power ON for a long time when the transceiver is defective.

6.DO NOT transmit power into a signal generator or a sweep generator.

7.ALWAYS connect a 30 dB to 40 dB attenuator between the transceiver and a deviation meter or spectrum analyzer when using such test equipment.

8.READ the instructions of test equipment thoroughly before connecting equipment to the transceiver.

Icom, Icom Inc. and logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.

Image 2
Contents VHF Transceiver Introduction Table of Contents Section Specifications USA-01, GEN-01 EUR-01Section Inside Views Front UnitDisassembly Instructions Removing the Chassis UnitOptional Unit Installation UT-96R, UT-109R and UT-110R installationFM if IC IC3 Receiver CircuitsRF Circuit Main Unit CTCSS/DTCS Squelch Circuit Noise SquelchTone Squelch DtmfAPC Circuit RF Unit Modulation Circuit Main UnitTransmit Amplifiers RF Unit TX VCOPLL Circuit Main Unit Power Supply Circuits Main UnitPLL Circuit Expand IC Front Unit IC505 Port Allocations2 D/A Converter Main Unit IC20 Adjustment Procedures PreparationConnection PC Screen Example Frequency Adjustment FrequencyTransmit Adjustment PowerReceive Adjustment ConvenientParts List Front UnitMain Unit Order Description LocationMain Unit Main Unit Main Unit Main Unit RF Unit SKHLLFA010VR Unit Main Unit Jack UnitMechanical Parts and Disassembly Chassis PartsVR Unit Semiconductor Information Transistors and FETsBoard Layouts Front Unit Main UnitBottom View Jack Unit Block Diagram RF UnitVoltage Diagrams Front UnitRF Unit Section BC-160Page 32, Kamiminami, Hirano-ku, Osaka 547-0003, Japan