SUPER MICRO Computer AS1021M-82 Connecting the Control Panel, Front Control Panel Header Pins JF1

Page 40

AS1021M-T2/1021M-82 User's Manual

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-1 for the pin locations of the various front control panel buttons and LED indi- cators. Please note that even and odd numbered pins are on opposite sides of each header.

All JF1 wires have been bundled into single keyed ribbon cable to simplify their connection. The red wire in the ribbon cable plugs into pin 1 of JF1. Connect the other end of the cable to the Control Panel printed circuit board, located just behind the system status LEDs in the chassis.

See the Connector Defi nitions section in this chapter for details and pin descrip- tions of JF1.

Figure 5-1. Front Control Panel Header Pins (JF1)

20

19

Ground

NMI

x (key)

x (key)

Power LED

Vcc

HDD LED

Vcc

NIC1

Vcc

NIC2

Vcc

OH/Fan Fail LED

Vcc

Power Fail LED

Vcc

Ground

Reset

Ground

Power

2

1

5-6

Image 40
Contents AS1021M-T2 AS1021M-82 Manual Revision Release Date October 3 About This Manual PrefaceManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup SgpioBios AppendicesPage Chapter Introduction OverviewServerboard Features ProcessorsMemory Serial ATAServer Chassis Features SATA/SCSI Subsystem Control PanelBackplane Cooling SystemNVidia MCP55 Pro Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-PacificPreparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Outer Rails Locking TabsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Chapter System Interface Control Panel ButtonsControl Panel LEDs Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup PrecautionsHandling the Serverboard UnpackingInstalling the CPU Backplates Processor and Heatsink InstallationInstalling the Processor install to the CPU#1 socket first Page Installing the Heatsink Retention Modules Installing the HeatsinkConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins JF1Installing Memory I/O PortsMemory Support Optimizing memory performance3b. Top View of DDR Slot Adding PCI Cards PCI card installationPCI Expansion Slots Serverboard Details H8DMR-82 LayoutConnectors Description Jumpers Description Default SettingH8DMR-82/H8DMR-i2 Quick Reference ATX Power Connector Processor Power ConnectorAuxiliary Power Connector NMI ButtonPower LED Overheat/Fan Fail LEDPower Fail LED Reset ButtonPower Button Universal Serial Bus Ports USB0/1Extra USB Headers Serial PortsFan Headers JLAN1/2 Ethernet PortsPower LED/Speaker ATX PS/2 Keyboard and PS/2 Mouse PortsChassis Intrusion Overheat LEDWake-On-LAN Wake-On-Ring3rd Power Supply Alarm Reset Header Compact Flash Card PWR ConnectorPower Fail Header Jumper SettingsExplanation Jumpers VGA Enable/Disable 3rd Power Supply Fail Detect Enable/DisableCmos Clear Watch Dog I2C to PCI Enable/DisablePCI-X Slot Freq. Select Scsi Termination Enable/ Disable H8DMR-82 only Scsi Controller Enable/ Disable H8DMR-82 onlyCompact Flash Master Slave Onboard Indicators +5V Standby Power LEDLAN1/LAN2 LEDs Scsi Activity LEDs H8DMR- 82 onlyFloppy Connector Floppy, IDE, Sata and Scsi Drive ConnectionsIDE Connector Sata PortsScsi Connectors H8DMR-82 only Diffsens TermpwrPage Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear ViewsInstalling a new fan System FansSystem Fan Failure Replacing System Cooling FansDrive Bay Installation/Removal Removing the Front BezelAccessing the Drive Bays Removing the Front BezelSATA/SCSI Drive Installation Mounting a SATA/SCSI drive in a drive carrierInstalling/removing hot-swap SATA/SCSI drives DVD-ROM and Floppy Drive Installation Power Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Chapter Starting the Setup UtilityIntroduction Bios Features Advanced Settings MenuMain Menu Advanced Acpi Configuration NVidia RAID Setup Floppy/IDE/SATA ConfigurationLBA/Large Mode Primary IDE Master/SlaveType Block Multi-Sector TransferDMA Mode A.R.TBit Data Transfer Serial ATA0/1/2 Primary/Secondary ChannelDMA Mode PCI/PnP Configuration Advanced Chipset Control NorthBridge ConfigurationSouthBridge Configuration Processor Clock Options Device ConfigurationDMI Event Logging Console RedirectionHardware Health Configuration System Fan MonitorLevel1 Temperature Level2 TemperatureFAN1 Speed through FAN5 Speed FAN1 Speed Down TimeIpmi 1.5 Configuration Boot Menu Boot Device PriorityHard Disk Drives Removable DrivesSecurity Menu OS InstallationCD/DVD Drives Exit Menu Amibios Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description Page Appendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C System Specifications Weight Power SupplyMotherboard ChassisRegulatory Compliance