SUPER MICRO Computer AS1021M-82, AS1021M-T2 Floppy/IDE/SATA Conﬁguration, NVidia RAID Setup

Page 76

AS1021M-T2/1021M-82 User's Manual

Floppy/IDE/SATA Conﬁguration

Onboard Floppy Controller

Use this setting to Enable or Disable the onboard ﬂ oppy controller.

Floppy A

Move the cursor to these ﬁ elds via up and down <arrow> keys to select the ﬂ oppy type. The options are Disabled, 360 KB 5 1/4", 1.2 MB 5 1/4", 720 KB 3½", 1.44 MB 3½”, and 2.88 MB 3½".

Onboard IDE Controller

There is a single ﬂ oppy controller on the motherboard, which may be Enabled or Disabled with this setting.

Serial ATA Devices

This setting is used to determine if SATA drives will be used and how many. Op- tions are Disabled, Device 0, Device 0/1 and Device 0/1/2.

nVidia RAID Setup

nVidia RAID Function

This setting is used to Enable or Disable the nVidia ROM. If Enabled, the set-

ting below will appear.

SATA0/1/2 Primary/Secondary Channel

This setting is used to Enable or Disable the SATA0 Primary, SATA0 Second- ary, SATA1 Primary, SATA1 Secondary, SATA2 Primary and SATA2 Secondary channels (six settings total).

7-4

Image 76

Contents AS1021M-T2 AS1021M-82 Manual Revision Release Date October 3 About This Manual PrefaceManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup SgpioBios AppendicesPage Chapter Introduction OverviewServerboard Features ProcessorsMemory Serial ATAServer Chassis Features SATA/SCSI Subsystem Control PanelBackplane Cooling SystemNVidia MCP55 Pro Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-PaciﬁcPreparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Outer Rails Locking TabsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Chapter System Interface Control Panel ButtonsControl Panel LEDs Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup PrecautionsHandling the Serverboard UnpackingInstalling the CPU Backplates Processor and Heatsink InstallationInstalling the Processor install to the CPU#1 socket ﬁrst Page Installing the Heatsink Retention Modules Installing the HeatsinkConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins JF1Installing Memory I/O PortsMemory Support Optimizing memory performance3b. Top View of DDR Slot Adding PCI Cards PCI card installationPCI Expansion Slots Serverboard Details H8DMR-82 LayoutConnectors Description Jumpers Description Default SettingH8DMR-82/H8DMR-i2 Quick Reference ATX Power Connector Processor Power ConnectorAuxiliary Power Connector NMI ButtonPower LED Overheat/Fan Fail LEDPower Fail LED Reset ButtonPower Button Universal Serial Bus Ports USB0/1Extra USB Headers Serial PortsFan Headers JLAN1/2 Ethernet PortsPower LED/Speaker ATX PS/2 Keyboard and PS/2 Mouse PortsChassis Intrusion Overheat LEDWake-On-LAN Wake-On-Ring3rd Power Supply Alarm Reset Header Compact Flash Card PWR ConnectorPower Fail Header Jumper SettingsExplanation Jumpers VGA Enable/Disable 3rd Power Supply Fail Detect Enable/DisableCmos Clear Watch Dog I2C to PCI Enable/DisablePCI-X Slot Freq. Select Scsi Termination Enable/ Disable H8DMR-82 only Scsi Controller Enable/ Disable H8DMR-82 onlyCompact Flash Master Slave Onboard Indicators +5V Standby Power LEDLAN1/LAN2 LEDs Scsi Activity LEDs H8DMR- 82 onlyFloppy Connector Floppy, IDE, Sata and Scsi Drive ConnectionsIDE Connector Sata PortsScsi Connectors H8DMR-82 only Diffsens TermpwrPage Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear ViewsInstalling a new fan System FansSystem Fan Failure Replacing System Cooling FansDrive Bay Installation/Removal Removing the Front BezelAccessing the Drive Bays Removing the Front BezelSATA/SCSI Drive Installation Mounting a SATA/SCSI drive in a drive carrierInstalling/removing hot-swap SATA/SCSI drives DVD-ROM and Floppy Drive Installation Power Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Chapter Starting the Setup UtilityIntroduction Bios Features Advanced Settings MenuMain Menu Advanced Acpi Conﬁguration NVidia RAID Setup Floppy/IDE/SATA ConﬁgurationLBA/Large Mode Primary IDE Master/SlaveType Block Multi-Sector TransferDMA Mode A.R.TBit Data Transfer Serial ATA0/1/2 Primary/Secondary ChannelDMA Mode PCI/PnP Conﬁguration Advanced Chipset Control NorthBridge ConﬁgurationSouthBridge Conﬁguration Processor Clock Options Device ConﬁgurationDMI Event Logging Console RedirectionHardware Health Conﬁguration System Fan MonitorLevel1 Temperature Level2 TemperatureFAN1 Speed through FAN5 Speed FAN1 Speed Down TimeIpmi 1.5 Conﬁguration Boot Menu Boot Device PriorityHard Disk Drives Removable DrivesSecurity Menu OS InstallationCD/DVD Drives Exit Menu Amibios Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description Page Appendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C System Speciﬁcations Weight Power SupplyMotherboard ChassisRegulatory Compliance