Insignia 105SX There is no transducer detected, There is no bottom reading visible on the display

Insignia manual Using the 105SX, HOW Sonar Works
Insignia 105SX manual Simulator Operation, Feature Memory
Insignia 105SX manual What YOU see ON-SCREEN, What You See On-Screen
Insignia 105SX manual When in Auto mode, the horizontal
Insignia 105SX manual What YOU see on Screen Insignia 105SX manual Control Functions Insignia manual Using the 105SX Insignia 105SX manual Range of Adjustment Indicator Insignia 105SX manual Menu Functions Insignia manual Using the 105SX Insignia 105SX manual Depth Range Upper Zoom Limit Insignia 105SX manual On the right side of the display. Zoom can
Insignia manual Using the 105SX
Insignia 105SX manual Bottom Black. There are two
Insignia 105SX manual Raw Sonar ID+ On
Insignia 105SX manual Advanced Features, Using the Diagnostic Feature
Insignia 105SX manual Maintenance and Warranty
Insignia 105SX manual Troubleshooting, Nothing happens when I turn the unit on
Insignia 105SX manual There is no transducer detected, There is no bottom reading visible on the display
Insignia 105SX manual Unit comes on before I press POWER, and won’t turn off, Get gaps in the reading at high speeds
Insignia 105SX manual Humminbird ONE Year Full Warranty
Insignia 105SX manual Service Policy
Insignia 105SX manual Customer Resource Center
Insignia 105SX manual Specifications, Top
Page 26

MAINTENANCE AND WARRANTY

TROUBLESHOOTING

Check the power connection to the 105SX. It is possible to force the power cable connector into the cable holder incorrectly. If the connector is reversed, the unit will not work. Examine the contacts on the back of the unit to ensure there is no corrosion. Finally, ensure the unit is firmly seated on the mount. The electrical contacts are not made until the unit is fully seated.

Ensure the metal cable retainer is properly installed in the mount. If not, the power connected may push out when the unit is put on the mount.

2. There is no transducer detected.

The 105SX has the ability to detect and identify that a transducer is connected. If, at power up, a message indicates “transducer not connect- ed,” only simulator operation is possible. First, ensure that an appropriate transducer connector is positioned correctly in the connector holder, and that the unit is fully seated on the mount. The 105SX will work with the standard single beam transducer.

Second, inspect the transducer cable from end to end for breaks, kinks, or cuts in the outer casing of the cable. Also ensure the transducer is fully submerged in water. If the transducer is connected to the unit through a switch, temporarily connect it directly to the unit and try again. If none of these items identifies an obvious problem, the transducer itself is probably the problem. Be sure to include the transducer if returning the unit for repair.

3. There is no bottom reading visible on the display.

There are a number of possible causes for this condition. If the loss of bottom information occurs only at high boat speeds, the transducer needs adjusting. If the digital depth readout is working but there is no bottom visible on-screen, it is possible the depth range has been adjusted manually to a range lower than what is needed to display the bottom. Also, in very deep water, it may be necessary to manually increase the sensitivity setting to maintain a graphic depiction of the bottom.

If you are using a transducer switch to connect two transducers to the 105SX, ensure the switch is in the correct position to connect a transducer that is in water. (If a trolling motor transducer is selected and the trolling motor is out of water, no sonar information appears.)

If none of the above solve the problem, inspect the transducer cable from end to end for breaks, kinks, or cuts in the outer casing of the cable. If

24

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Operations Manual Thank YOU Table of Contents Installation Overview Installation PreparationAccessories Parts SuppliedInstallation Overview Determining How to Mount the TransducerPortable Mounting Alternate Transducers and Mounting MethodsAlternate Transducers and Mounting Methods Trolling Motor MountingTransducer Exchange Beginning InstallationTransducer Exchange HOW Sonar Works Using the 105SXHOW Sonar Works Simulator Operation Feature MemorySimulator Operation What YOU see ON-SCREEN What You See On-ScreenWhen in Auto mode, the horizontal What YOU see on Screen Control Functions Control FunctionsUsing the 105SX Range of Adjustment Indicator Menu Functions Menu FunctionsUsing the 105SX Depth Range Upper Zoom Limit On the right side of the display. Zoom can Using the 105SX Bottom Black. There are two Raw Sonar ID+ On Using the Diagnostic Feature Advanced FeaturesUsing the Diagnostic Feature Maintenance Maintenance and WarrantyMaintenance Nothing happens when I turn the unit on TroubleshootingTroubleshooting There is no transducer detected There is no bottom reading visible on the displayGet gaps in the reading at high speeds Unit comes on before I press POWER, and won’t turn offMy unit loses power at high speeds Warranty Humminbird ONE Year Full WarrantyService Policy Service PolicyCustomer Resource Center Customer Resource CenterSpecifications TOP
Top Page Image Contents