Simrad MN000802A-G manual Warranty, Feedback from you

Page 3

1.5 Warranty

The Navico Warranty Statement is supplied as a separate document. It is shipped with the Product Registration Card.

In case of any queries, refer to the Manufacturer of Radar/Chart/Multifunction Displays

1.6 Feedback from you

Your feedback is important and helps Navico ensure that this manual is a valuable resource for all marine technicians. E-mail your comments or suggestions about this manual to the following address: manuals@navico.com

2 2 kW Radar Installation Manual

Image 3

Contents KW Radar CE Compliance KW Radar Installation ManualFCC Statement Industry CanadaFeedback from you WarrantyContents Connect to Lowrance Displays MaintenanceConnect Simrad NX40 / NX45, Northstar M84 / M121 Connect Northstar 6000i13 2 kW radar system specifications Please Read Carefully Before USE PrefaceEthernet Connectivity Serial ConnectivityPage Introduction to the Navico radar system Brand Display heads that support the Navico radar systemBranding information 2 kw Radar overview Serial Connectivity Install the radar Dont do this Choose the scanner locationPower boat installations Yacht installations How to find the optimum height for the scannerScanner model Value half the -3 dB beam Width How to find the theoretical maximum detection range 2 kW scanner dimensions How to reduce false echoes and shadow zonesInstall the 2 kW scanner unit Install a scanner on a trestleInstall the radar processor Check the 2 kW radar parts Page Page Wiring guidelines Page Page Page Yellow #24 White big #12 Shell Braid shield 2 kW radar processor connections Only Connect the power cableRadar system checklist Connect the ground wireEthernet Crossover cable Connect Simrad GB40 or NorthstarParts needed to connect radar to a GB40 or 8000i system Ethernet Cables Simrad GB40 and NorthstarOptional parts to connect GB40 only Optional parts to connect GB40AT10-HD Simrad GB40 connection using SimNet heading Key Part Description Number Northstar 8000i / Simrad GB 40 using Nmea 0183 headingPage Commision the radar using a GB40 or ¾ tarting up RadarPin Function ¾ To correct ¾ Set Radar Range offset trigger Delay¾ Select OK to confirm the new setting ¾ To enter Radar setup optionsRadar information Radar Power on ActionConnect Simrad NX40 / NX45, Northstar M84 / M121 Parts neededRadar connection kit AA002461 Quanti Part name NOR Connect the 2 kW radar processor to an M84 or M121 Display¾ Zero bearing Set up the radar with the Northstar M84 or M121¾ To enable the radar functionality ¾ Park position¾ Antenna height Connect Northstar 6000i Parts needed to connct to a Northstar 6000iSerial comms extension cables + adaptor Quanti Part name Connect the 2 kW radar processor to a 6000i or 6100i display AUX NmeaPage Nmea 1 in B Remote Power OUT ShieldPower Nmea 1 in aPage ¾ Power on Option Turn the radar on ¾ Turn on the radar as follows¾ Turn the radar off Before you turn on the radar for the first timeAdjust the appearance settings Configure the navigator communicationsPrepare for calibration Disable the heading sensor inputHeading sensor requirements Calibrating the radar¾ To select a different curve Set the trigger delayTune the radar Set the STC CurveSet the heading calibration heading sensor installed Press Page 3, Page 4, and InstallPress Page 2, Page 3, Page 4, and Install Set the heading calibration heading sensor not installed Restore all the factory settingsRestore the factory appearance settings Manual tuning procedure for the 6000i or 6100i system ¾ Next, set the scale to 1/8 nautical miles as followsPress Sea Clutter Heading Sensor Optional Quantit Part Name Connect to Lowrance DisplaysParts needed to connect to Lowrance displays RIM300 Radar Interface Module Quantit Part name10.2 RIM300 Setup the radar with Lowrance displays Setup the basics ¾ Trigger Delay Preparation Radar SetupMain Bang Suppression Trigger DelayAdjust Main Bang Suppression Before heading line adjustment After heading line adjustment Maintenance General maintenanceScanner maintenance Other maintenance items If the scanner fails to turn Technical support, service and repairsTroubleshoot the radar Radar is not operating correctlyHow to reduce noise and interference Make sure the power is present and correctly wiredConfirm the equipment installed Make Model Serial Number Software Version Are range rings displayed?13 2 kW radar system specifications KW scannerDC input To 15.6 V DC DC 12 V system only NS-RDR-1021MD KW Radar processor specifications