Furuno 1715 manual Important Notices, European Union, Usa, Other countries

Page 2

IMPORTANT NOTICES

General

The operator of this equipment must read and follow the descriptions in this manual. Wrong operation or maintenance can cancel the warranty or cause injury.

Do not copy any part of this manual without written permission from FURUNO.

If this manual is lost or worn, contact your dealer about replacement.

The contents of this manual and equipment specifications can change without notice.

The example screens (or illustrations) shown in this manual can be different from the screens you see on your display. The screens you see depend on your system configuration and equipment settings.

Save this manual for future reference.

Any modification of the equipment (including software) by persons not authorized by FURUNO will cancel the warranty.

All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

How to discard this product

Discard this product according to local regulations for the disposal of industrial waste. For disposal in the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the correct method of disposal.

How to discard a used battery

Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter on Maintenance. Follow the instructions below if a battery is used. Tape the + and - terminals of battery before disposal to prevent fire, heat generation caused by short circuit.

In the European Union

The crossed-out trash can symbol indicates that all types of batteries must not be discarded in standard trash, or at a trash site. Take the used batteries to a battery collection site according to your national legislation and the Batteries Directive 2006/66/EU.

Cd

In the USA

The Mobius loop symbol (three chasing arrows) indicates that Ni-Cd and lead-acid rechargeable batteries must be recycled. Take the used batteries to a battery collection site according to local laws.

Ni-Cd Pb

In the other countries

There are no international standards for the battery recycle symbol. The number of symbols can increase when the other countries make their own recycling symbols in the future.

i

Image 2
Contents Model Model USA Important NoticesEuropean Union Other countriesSafety Instructions Compliance with R&TTE Directive 1999/5/EC Table of Contents Word to the Owner of the Model FeaturesForeword System Configuration NavigatorEquipment Lists Antenna installation materialsDisplay unit installation materials Standard supplyControls How to remove the hard coverOperation Display unitAbout the LCD IndicationsIndications Transmitting, Standby Turning Power On/OffBrilliance/contrast adjustment window Startup screenChoosing the Range Adjusting Display Contrast, BrillianceAutomatic gain adjustment Receiver SensitivityManual gain adjustment Automatic adjustment by the A/C SEA controlManual adjustment of A/C SEA Automatic A/C SEA adjustmentMeasuring range by the range rings Suppressing Rain ClutterMeasuring the Range Measuring range by the cursorMeasuring bearing with the cursor Measuring the BearingShifting the Display Measuring bearing with the EBLZoom display ZoomUser Menu Overview User menu,User menu description Heading LineInterference Rejector Appearance of interferenceEcho Stretch Noise RejectorEcho Trail, Trail Brilliance Echo trailsSilencing the audio alarm Guard AlarmSetting a guard zone Canceling the guard zone and guard alarmSuppressing Heavy Rain Clutter Setting watchman stand-by intervalWatchman Panel BacklightingProg Key Resetting Distance Run24 Hue Outputting Target Position to a Plotter30 00.065N 130 00.574E Setting up Nav Data DisplaysTurning Navigation Data On/Off 30 00.065N 21 nmNav data displays 130 00.574E1 of system menu System MenuSystem menu description Waypoint Mark The waypoint mark shows3 of system menu Maintenance program MAINTENANCE, TroubleshootingMaintenance Period Check point ActionReplacing the Fuse TroubleshootingTroubleshooting If… But… Then…Display unit DiagnosticsInstallation menu Antenna unitReplacing the Magnetron Test PatternClearing the Memory Replacing the Synchro BeltMounting considerations InstallationAntenna Unit Installation Mounting on a platformAntenna cable and gasket to use How to fasten the antenna base to platformAntenna unit, inside view Contents of radome mounting assy Mounting using the optional mounting bracketHow to fix the EMI core Connecting antenna cable to antenna unitDesktop, overhead mounting Display Unit InstallationMounting Flush mountingWiring WiringConnecting external equipment Input sentencesHeading alignment AdjustmentsConnecting the external buzzer Display unit, rear viewTiming adjustment Nmea port setup, GPS Waas setup Timing adjustment displayMagnetron Heater Voltage MD boardMenu Tree Trail Brilliance LOW, High System MenuSpecifications of Marine Radar SP-1Environmental Conditions SP-2Page Page Page Page Marine Radar Page 00014790912