Furuno 1715 manual Mounting using the optional mounting bracket, How to fix the EMI core

Page 32

3. INSTALLATION

8.Tighten the cable gland to fix the antenna cable.

Gasket

Cable Gland

Tighten gland so this length is within 12 mm.

Antenna unit, inside view

9.Referring to the figure below, fasten the shield cable with a screw (M4 x 10) on the chassis to ground the unit.

Connect 9 pin

13.Fasten the EMI core fixing plate with screw (supplied).

Screw (M4 x 15)

Align bend with corner of chassis.

EMI Core

Fixing Plate

EMI Core

How to fix the EMI core

14.Temporarily close the cover. You will need to open the cover later to confirm magnetron voltage.

Mounting using the optional mounting bracket

A mounting bracket for fastening the antenna unit to a mast (70-125 mm diameter) on a sailboat is optionally available.

Type OP03-93, Code 008-445-080

connector

Connect shield here.

Contents of radome mounting assy.

here (J801).

Connecting antenna cable to antenna unit

10.Attach the EMI core to the antenna cable. Set the EMI core fixing band to the EMI core.

Fixing band

This bend should be facing to the cable entrance.

EMI core fixing band

11.Connect the 9-pin connector of the antenna cable to J801. See the illustration on the previous page for location.

12.Refasten the shield plate with 10 screws. Be sure not to pinch the cable from the rotation detector with the shield plate.

 

 

 

 

Name

Type

Code No.

Qty

Bolt

M4 x 12

000-804-725

4

Bolt

M8 x 20

000-805-707

8

Mounting

03-018-9001-0

100-206-740

1

plate

 

 

 

Support

03-018-9005-0

100-206-780

1

plate (1)

 

 

 

Support

03-018-9006-0

100-206-790

1

plate (2)

 

 

 

Bracket (1)

03-028-9101-0

100-206-810

1

Bracket (2)

03-028-9102-0

100-206-820

1

Fixing plate

03-028-9103-0

100-206-830

2

1.Remove mounting hardware at the bottom of the antenna base. You may discard the mounting hardware.

2.Assemble the mounting bracket as below and fasten it to a mast.

3.Fasten the antenna unit to the mounting bracket with hexagon head bolts (M10 x 25).

24

Image 32
Contents Model Model Important Notices European UnionUSA Other countriesSafety Instructions Compliance with R&TTE Directive 1999/5/EC Table of Contents Word to the Owner of the Model FeaturesForeword System Configuration NavigatorAntenna installation materials Display unit installation materialsEquipment Lists Standard supplyHow to remove the hard cover OperationControls Display unitAbout the LCD IndicationsIndications Turning Power On/Off Brilliance/contrast adjustment windowTransmitting, Standby Startup screenAdjusting Display Contrast, Brilliance Automatic gain adjustmentChoosing the Range Receiver SensitivityAutomatic adjustment by the A/C SEA control Manual adjustment of A/C SEAManual gain adjustment Automatic A/C SEA adjustmentSuppressing Rain Clutter Measuring the RangeMeasuring range by the range rings Measuring range by the cursorMeasuring the Bearing Shifting the DisplayMeasuring bearing with the cursor Measuring bearing with the EBLZoom User Menu OverviewZoom display User menu,Heading Line Interference RejectorUser menu description Appearance of interferenceNoise Rejector Echo Trail, Trail BrillianceEcho Stretch Echo trailsGuard Alarm Setting a guard zoneSilencing the audio alarm Canceling the guard zone and guard alarmSetting watchman stand-by interval WatchmanSuppressing Heavy Rain Clutter Panel BacklightingResetting Distance Run 24 HueProg Key Outputting Target Position to a Plotter30 00.065N 130 00.574E Setting up Nav Data DisplaysTurning Navigation Data On/Off 21 nm Nav data displays30 00.065N 130 00.574ESystem Menu System menu description1 of system menu Waypoint Mark The waypoint mark shows3 of system menu MAINTENANCE, Troubleshooting MaintenanceMaintenance program Period Check point ActionTroubleshooting TroubleshootingReplacing the Fuse If… But… Then…Diagnostics Installation menuDisplay unit Antenna unitTest Pattern Clearing the MemoryReplacing the Magnetron Replacing the Synchro BeltInstallation Antenna Unit InstallationMounting considerations Mounting on a platformAntenna cable and gasket to use How to fasten the antenna base to platformAntenna unit, inside view Mounting using the optional mounting bracket How to fix the EMI coreContents of radome mounting assy Connecting antenna cable to antenna unitDisplay Unit Installation MountingDesktop, overhead mounting Flush mountingWiring Connecting external equipmentWiring Input sentencesAdjustments Connecting the external buzzerHeading alignment Display unit, rear viewTiming adjustment Nmea port setup, GPS Waas setup Timing adjustment displayMagnetron Heater Voltage MD boardMenu Tree Trail Brilliance LOW, High System MenuSpecifications of Marine Radar SP-1Environmental Conditions SP-2Page Page Page Page Marine Radar Page 00014790912