INSTALLATION/OPERATION Instructions | Jackson TSC-66, TS-66G

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

VISUAL INSPECTION: Before installing the unit, check the container and machine for damage. A damaged container is an indi- cator that there may be some damage to the machine. If there is damage to both the container and machine, do not throw away the container. The dishmachine has been inspected and packed at the factory and is expected to arrive to you in new, undam- aged condition. However, rough handling by carriers or others may result in there being damage to the unit while in transit. If such a situation occurs, do not return the unit to Jackson; instead, contact the carrier and ask them to send a representative to the site to inspect the damage to the unit and to complete an inspection report. You must contact the carrier within 48 hours of receiving the machine. Also, contact the dealer through which you purchased the unit.

UNPACKING THE DISHMACHINE: Once the machine has been removed from the container, ensure that there are no miss- ing parts from the machine. This may not be obvious at first. If it is discovered that an item is missing, contact Jackson imme- diately to have the missing item shipped to you.

LEVEL THE DISHMACHINE: The dishmachine is designed to operate while being level. This is
important to prevent any damage to the machine during operation and to ensure the best results
when washing ware. The unit comes with adjustable bullet feet, which can be turned using a pair of
channel locks or by hand if the unit can be raised safely. Ensure that the unit is level from side to side
and from front to back before making any connections.	Frame with Adjustable Foot
	Frame with Adjustable Foot

PLUMBING THE DISHMACHINE: All plumbing connections must comply with all applicable local, state, and national plumb- ing codes. The plumber is responsible for ensuring that the incoming water line is thoroughly flushed prior to connecting it to any component of the dishmachine. It is necessary to remove all foreign debris from the water line that may potentially get trapped in the valves or cause an obstruction. Any valves that are fouled as a result of foreign matter left in the water line, and any expenses resulting from this fouling, are not the responsibility of the manufacturer.

CONNECTING THE DRAIN LINE: The drain for the models covered in this manual are gravity discharge drains. All piping from the machine to the drain must be a minimum 1 1/2” NPT and shall not be reduced. There must also be an air gap between the machine drain line and the floor sink or drain. If a grease trap is required by code, it should have a flow capacity of 30 gallons per minute.

WATER SUPPLY CONNECTION: Ensure that you have read the sec- tion entitled “PLUMBING THE DISHMACHINE” above before proceed- ing. Install the water supply line (1/2” pipe size minimum) to the dish- machine line strainer using copper pipe. It is recommended that a water shut-off valve be installed in the water line between the main supply and the machine to allow access for service. The water supply line is to be capable of 25 PSI “flow” pressure at the recommended temperature indicated on the data plate.

Adjusting screw

Locking nut

Incoming Plumbing Connection

In areas where the water pressure fluctuates or is greater than the recommended pressure, it is suggested that a water pres- sure regulator be installed. The models covered in this manual do come with water pressure regulators as standard equipment. Please notify Jackson immediately if this component is not present on your machine.

Do not confuse static pressure with flow pressure. Static pressure is the line pressure in a “no flow” condition (all valves and services are closed). Flow pressure is the pressure in the fill line when the fill valve is opened during the cycle.

It is also recommended that a shock absorber (not supplied) be installed in the incoming water line. This prevents line hammer (hydraulic shock), induced by the solenoid valve as it operates, from causing damage to the equipment.

PLUMBING CHECK: Slowly turn on the water supply to the machine after the incoming fill line and the drain line have been installed. Check for any leaks and repair as required. All leaks must be repaired prior to placing the machine in operation.

GAS CONNECTIONS: Some machines covered in this manual are designed to use gas as an outside source of heat for wash tank water. The machines come with connections by which an outside source needs to be connected. Connect all incoming gas lines in accordance with the gas booster manufacturer’s instructions. Ensure that all applicable codes and regulations are adhered to.

TS Series Conveyors Technical Manual 7610-002-98-29

Issued: 02-15-2006 Revised: N/A

TS-66G, TSC-66GPP, TSC-44GP, TS-44GP, TS-44 specifications

The Jackson TSC-66, TS-66, TSC-44, TS-44, and TS-44GP are a line of versatile, high-performance scorers designed to meet the diverse needs of any construction or road maintenance crew. Known for their reliability and exceptional build quality, these machines have become trusted tools in various applications, from road construction to surface maintenance.

Starting with the TSC-66, it stands as a powerful tool equipped with a robust engine that delivers high-performance results even under demanding conditions. The primary feature is its adjustable cutting depth, allowing operators to customize the depth of the cut based on the project requirements. Additionally, the TSC-66 comes with a user-friendly interface, featuring intuitive controls that enhance operational efficiency. The mobility of this model is another notable characteristic, thanks to its compact design and durable wheels, facilitating easy transport between job sites.

The TS-66 model shares many features with the TSC-66 but offers enhanced versatility with its multi-function capabilities. This machine can tackle various tasks beyond surface cutting, including grinding and finishing, which makes it an excellent choice for contractors specializing in diverse projects. Its high-torque motor is engineered for prolonged use, and its low-vibration technology ensures comfort during operation.

The TSC-44 and TS-44 models provide similar functionality with a focus on compactness and weight. These machines are perfect for smaller jobs and can easily navigate tight spaces. Equipped with advanced hydraulic systems, they feature superior lifting and cutting capabilities, allowing them to perform effectively in various conditions.

The TS-44GP variant is designed for general-purpose applications, combining the features of its peers with added emphasis on durability and ease of use. Its construction is particularly noteworthy, utilizing heavy-duty materials that ensure a long operational life. The incorporation of advanced safety features across all models underscores Jackson's commitment to user safety, with protective guards and emergency stop mechanisms built into the design.

In summary, the Jackson TSC-66, TS-66, TSC-44, TS-44, and TS-44GP models collectively represent a commitment to quality, performance, and versatility in the scoring equipment market. With their unique features, advanced technology, and durable construction, these machines are engineered to excel in a variety of demanding applications, making them a valuable addition to any contractor’s toolkit.