Baja Marine 242 manual Nautical Terms

Page 24

Section 1 • Safety

19.Nautical Terms

Abeam – object 90 degrees ( 90° ) to center line on either side of boat.

Abaft – a point on a boat that is aft of another.

Aft - toward the rear or stern of the boat.

Beam - the maximum width of a boat.

Bilge - the lowest part of the hull on the inside where fluids collect.

Bow - the forward part of a boat.

Bow Eye - bolt with looped head mounted on extreme forward part of bow, used for towing or tying up boat.

Bulkhead - vertical partition in a boat

Chine - meeting juncture of side and bottom of boat.

Chock - deck fitting, used as a guide for mooring or anchor lines. Also, a wedge to stop wheels from rolling.

Cleat - deck fitting with arms or horns to which lines are tied or made fast.

Cockpit - the open space from which a boat is operated.

Deck - upper structure which covers the hull between gunwales.

Downwind - in the direction the wind is blowing toward

Draft – depth of water required to float boat and its propulsion system.

Fathom - six feet.

Fenders - rope or plastic pieces hung over the side to protect the hull from chafing against a dock or another boat.

Freeboard - height of exposed hull from water line to deck.

Ground tackle - general term referring to anchors, anchor lines, etc.

Gunwale (pronounced gun'l) - where the hull and deck come together; the "sides" of the boat in the cockpit area.

Hatch - an opening in the deck to provide access below.

Head - toilet or toilet area in a boat.

Headroom - vertical distance between the deck and cabin or canopy top.

Helm - steering and controls console.

Hull - the lower part of a boat beneath the deck and cockpit that provides buoyancy to float the weight of the craft and its load.

Keel - the major longitudinal member of a hull; the lowest external portion of a boat.

Knot - unit of speed in nautical miles per hour.

Lee - the side that is sheltered from the wind.

PFD - Personal Flotation Device; life jacket or preserver.

Port - term designating left side of the boat when facing forward.

Rudder - Movable fixture at the stern used for steering.

Scupper - hole permitting water to drain overboard from deck or cockpit.

Sheer - curve or sweep of the deck as viewed from the side.

Snub - to check or tighten a line suddenly.

Starboard - term designating right side of the boat.

Stern - the rear (aft) end of a boat.

Stern drive - outboard unit of an inboard/outboard (I/O) engine installation.

Stringer - longitudinal members fastened inside the hull for additional structural strength.

Transom - the rear part of the boat across the back, to which the drive unit and swim platform are attached.

Upwind - in the direction the wind is blowing from.

Wake - disturbed water that a boat leaves behind as a result of forward motion.

Windward - toward the direction from which the wind is blowing.

1.14

242 Islander®

Image 24
Contents Baja Marine IslanderFor information call 1-865-971-6270 or fax Welcome This page intentionally left blank Introduction Service, Parts and Repair for Your Boat Hull Identification Number HINManufacturer’s Certification About Your Express Limited Warranty Iii Ignition Protection Breakers and/or Fuses Speed changes you. TM Safety Safety LabelsLegally Mandated Minimum Required Equipment Carbon MonoxideFire Extinguishing System Carbon Monoxide Monitor Lifesaving Equipment Additional Recommended Equipment for Safe Operation Impaired OperationLoad Capacity Power Capacity StabilityMaintain Control WeatherGeneral Considerations Chart Your Course Water Sports SwimmingSkiing Emergency Situations GeneralMedical Emergency Water RescueFire Flooding, Swamping and CapsizingCollisions and Leaking Safety Hotlines International RequirementsGrounding Propulsion, Control or Steering FailureEnvironmental Considerations Waste DisposalExcessive Noise Wake/WashNautical Terms Key to Symbols on Controls & Prints This Page Intentionally Left Blank Baja Marine Corp This Page Intentionally Left Blank General Boat Arrangement Docking /Lifting /Trailering Passenger LocationsBoat Dimensions and Clearances Fig Basic Boat Dimensions and Clearances Metric Propulsion SystemPropellers General Deck Layout Power Trim Unit and Gauge Description of Major ControlsGear Shift and Throttle Control Trailer Switch Trim TabsIgnition Shutdown Switch Engine Alarm SystemImportant Gauges Tachometer and Hour MeterOil Pressure, Water Temperature, Voltmeter and Fuel Gauges Navigation and Anchor LightsUsing Your Boat Pre-Launch, Launch and Post- Launch ChecklistTrailer Launching and Loading Fueling the BoatBoarding Personal Flotation DevicesPassenger Instruction and Location Starting the EngineShifting to Drive the Boat Stopping the EnginePower Steering System Steering SystemBilge & Underwater Gear BilgeFuel & Oil Spillage Bilge PumpsMaintenance and Service Engines and Stern DriveBilge Blowers Vibration and CausesPropeller Removal and Installation Impact to Stern DriveGear case Fuel System Fuel SystemAnti-Siphon Valve Inboard/Outboard Engine Only Fueling Precautions Before and During Fueling ChecklistStatic Electricity and the Fuel System After Fueling Checklist This page intentionally left blank Electrical Systems Electrical SystemsDirect Current DC BatteriesElectrolytic Corrosion & Zinc Anodes Breakers and/or FusesFuse Panel Marine Electronic Cathodic Anti-corrosion System Mercathode Drive Pump Drive Pump w/ K-Plane Trim Tabs Ignition Switch Switch Panel Wire Information FIG This Page Intentionally Left Blank Options & Accessories Options & Accessories LocationsAutomatic Fire Extinguisher System Option Fire Extinguisher PortCanvas Canvas Care and Maintenance Swim Platform w/ Ladder OptionalDepth Finder Optional HornStereo System Head SystemsRequirements for Operators Portable Head with Pump-OutExhaust Systems VacuFlush Head OptionVent Filter Holding Tank OperationRequired Inspection, Service Maintenance Summary Guide for Inspection, Service and MaintenanceInterval Summary Guide For Inspection, Service and Maintenance IntervalUseful Service Information Inspection, Service and Maintenance Protocol Bilge AreaWinterization Checklist for Boats Stored on Land BatteryiesTopside and Supplies Boat StorageFitting Out After Storage Fuel SystemsFuel System MiscellaneousPower Steering System Maintenance Security ConsiderationsQuick Reference Checklist Boarding the Boat GeneralBoat Systems Starting the Engine Quick Reference Checklist cont’d Departing General Returning to Port GeneralQuick Reference Checklist cont’d Securing the BoatIf the Engine Does Not Start After Market Equipment Checklist Maintenance Log Maintenance Log Cont’d Paint Cleaning Agents & Other Substances Care & RefinishingStains & Scratches Fiberglass & GelcoatPermanently Moored or Docked Boats Topside AreasAcrylic Plastic Sheeting Plastic Glass Canvas and Clear VinylExterior Upholstery Fabric Interior Upholstery FabricThis Page Intentionally Left Blank Index Index Islander