Baja Marine 242 manual Power Capacity, Stability

Page 16

Section 1 • Safety

The number of seats does not indicate how many people a boat can safely carry in poor weather and rough water.

Above idle speed, all passengers must be seated on the seats provided.

242 Islander DOMESTIC CERTIFICATION PLATE (EXAMPLE) (FIG. 1.6.1)

MAXIMUM CAPACITIES

8 PERSONS OR 1600 LBS.

2000 POUNDS, PERSONS, GEAR

THIS BOAT COMPLIES WITH U.S. COAST GUARD SAFETY STANDARDS IN EFFECT ON THE DATE OF CERTIFICATION

MANUFACTURER: BAJA MARINE CORPORATION bucyrus, oh

MODEL: 242 Islander

DESIGN COMPLIANCE WITH NMMA REQUIREMENTS BELOW IS VERIFIED MFR. RESPONSIBLE FOR PRODUCTION CONTROL

LOAD AND CAPACITY * COMPARTMENT VENTILATION

STEERING, FUEL AND ELECTRICAL SYSTEMS

NAVIGATION LIGHTS * BASIC FLOTATION

MANEUVERABILITY

Certified

NMMA NATIONAL MARINE MANUFACTURERS ASSN.

!WARNING

When engine is running, keep passengers away from areas not designed for riding, such as seat backs, bow, gunwales, transom platform, front and rear decks and on sun pads.

Passengers can fall overboard if not seated properly on the seats provided.

!DANGER

Never carry more weight or passengers than indicated on the certification plate, regardless of weather or water conditions.

The boat can capsize, swamp or sink.

242 Islander CE OPTION CERTIFICATION PLATE (INTERNATIONAL) (EXAMPLE) (FIG. 1.6.2)

C E Baja Marine Corp.

0609

 

 

 

242 Islander

 

 

 

 

 

 

 

 

 

 

 

IMCI

MAXIMUM

 

 

 

C

 

 

 

 

 

 

8

 

+

 

 

= 608 kg

 

 

 

 

 

 

 

 

 

 

 

9.Power Capacity

The engine options available for your boat have been selected as the best suited for general use for this size boat. Do not install an engine larger than the largest option available. Your boat will be difficult to handle and will be less stable.

Your Baja® has been equipped with a propeller which our tests have shown to be the best suited for general use with your engine under normal conditions and load. Do not change the pitch of your propeller without getting your dealer's recommendations first. If you change to a different propeller pitch, under no circumstances use a propeller which allows the engine to operate at higher than recommended RPM. (Your engine manual specifies the maximum recommended RPM.)

To maintain rated power, propellers should be free of nicks, excessive pitting and any distortions that alter them from their original design. Badly damaged propellers should be replaced, but those that are chipped, bent or merely out of shape can be reconditioned by your marine dealer.

It is advisable to carry an extra propeller aboard in case you damage the one in use.

10.Stability

Your boat was manufactured to specific stability and flotation standards for the capacity shown on the certification plate. Any increase from the recommended load capacities will put your boat in jeopardy of capsizing, swamping and/or sinking.

1.6

242 Islander®

Image 16
Contents Baja Marine IslanderFor information call 1-865-971-6270 or fax Welcome This page intentionally left blank Introduction Hull Identification Number HIN Service, Parts and Repair for Your BoatManufacturer’s Certification About Your Express Limited Warranty Iii Ignition Protection Breakers and/or Fuses Speed changes you. TM Safety Safety LabelsCarbon Monoxide Legally Mandated Minimum Required EquipmentFire Extinguishing System Carbon Monoxide Monitor Lifesaving Equipment Impaired Operation Additional Recommended Equipment for Safe OperationLoad Capacity Power Capacity StabilityWeather Maintain ControlGeneral Considerations Chart Your Course Swimming Water SportsSkiing Emergency Situations GeneralMedical Emergency Water RescueFlooding, Swamping and Capsizing FireCollisions and Leaking Safety Hotlines International RequirementsGrounding Propulsion, Control or Steering FailureEnvironmental Considerations Waste DisposalExcessive Noise Wake/WashNautical Terms Key to Symbols on Controls & Prints This Page Intentionally Left Blank Baja Marine Corp This Page Intentionally Left Blank General Boat Arrangement Docking /Lifting /Trailering Passenger LocationsBoat Dimensions and Clearances Fig Propulsion System Basic Boat Dimensions and Clearances MetricPropellers General Deck Layout Description of Major Controls Power Trim Unit and GaugeGear Shift and Throttle Control Trailer Switch Trim TabsIgnition Shutdown Switch Engine Alarm SystemImportant Gauges Tachometer and Hour MeterOil Pressure, Water Temperature, Voltmeter and Fuel Gauges Navigation and Anchor LightsUsing Your Boat Pre-Launch, Launch and Post- Launch ChecklistTrailer Launching and Loading Fueling the BoatBoarding Personal Flotation DevicesPassenger Instruction and Location Starting the EngineShifting to Drive the Boat Stopping the EnginePower Steering System Steering SystemBilge & Underwater Gear BilgeFuel & Oil Spillage Bilge PumpsMaintenance and Service Engines and Stern DriveBilge Blowers Vibration and CausesPropeller Removal and Installation Impact to Stern DriveGear case Fuel System Fuel SystemAnti-Siphon Valve Inboard/Outboard Engine Only Before and During Fueling Checklist Fueling PrecautionsStatic Electricity and the Fuel System After Fueling Checklist This page intentionally left blank Electrical Systems Electrical SystemsDirect Current DC BatteriesBreakers and/or Fuses Electrolytic Corrosion & Zinc AnodesFuse Panel Marine Electronic Cathodic Anti-corrosion System Mercathode Drive Pump Drive Pump w/ K-Plane Trim Tabs Ignition Switch Switch Panel Wire Information FIG This Page Intentionally Left Blank Options & Accessories Options & Accessories LocationsFire Extinguisher Port Automatic Fire Extinguisher System OptionCanvas Canvas Care and Maintenance Swim Platform w/ Ladder OptionalDepth Finder Optional HornStereo System Head SystemsRequirements for Operators Portable Head with Pump-OutExhaust Systems VacuFlush Head OptionVent Filter Holding Tank OperationSummary Guide for Inspection, Service and Maintenance Required Inspection, Service MaintenanceInterval Summary Guide For Inspection, Service and Maintenance IntervalUseful Service Information Inspection, Service and Maintenance Protocol Bilge AreaWinterization Checklist for Boats Stored on Land BatteryiesTopside and Supplies Boat StorageFitting Out After Storage Fuel SystemsFuel System MiscellaneousPower Steering System Maintenance Security ConsiderationsBoarding the Boat General Quick Reference ChecklistBoat Systems Starting the Engine Quick Reference Checklist cont’d Departing General Returning to Port GeneralSecuring the Boat Quick Reference Checklist cont’dIf the Engine Does Not Start After Market Equipment Checklist Maintenance Log Maintenance Log Cont’d Paint Cleaning Agents & Other Substances Care & RefinishingStains & Scratches Fiberglass & GelcoatPermanently Moored or Docked Boats Topside AreasAcrylic Plastic Sheeting Plastic Glass Canvas and Clear VinylExterior Upholstery Fabric Interior Upholstery FabricThis Page Intentionally Left Blank Index Index Islander