Baja Marine 192 Islander manual Fitting Out After Storage, Fuel Systems, Miscellaneous

Page 68

Section 8 • Required Inspection, Service, &

Maintenance

Keep under a trickle charge.

When placing battery back into service, remove excess grease from terminals, recharge as necessary and reinstall in boat.

D.Fuel Systems

Gasoline

Fill fuel tank with gasoline and the recommended amount of stabilizer and conditioner such as “Stabil®”.

Run engine(s) for ten minutes to ensure that all gasoline in the carburetor and fuel lines are treated.

Diesel

Fill fuel tank with diesel and recommended amount of biocide, “Biobor®”, which prevents bacteria and fungi from contaminating diesel fuel that contains some water.

Diesel fuel should also get a petroleum distillate additive, such as “Stabil®” or Racor® RX100”. This will absorb water in the fuel and prevent freezing problems.

Run engine(s) for ten minutes to ensure that all diesel fuel in injectors and fuel lines is treated.

DETAILED WINTERIZING, OPERATING INSTRUCTIONSAND WARRANTY INFORMATION ARE PROVIDED BY THE EQUIPMENT MANUFACTURER AND CAN BE FOUND IN THE OWNER’S PACKET.

!CAUTION

Do not overfill. Filling a tank until the fuel flows from vents is dangerous. Allow room for expansion.

5.Fitting Out After Storage

A.Fuel System

Check the entire fuel system for loose connections, worn hoses, leaks, etc. and repair. This is a primary safety precaution.

Check fuel lines for damage and make sure that they do not come in contact with any moving parts.

B.Battery(ies)

Before installing the batteries, clean the terminal posts with a wire brush or steel wool and then attach the cables. After the cable clamps are tightened, smear the post and clamps with vaseline or grease to exclude air and acid. Do not apply grease before attaching and tightening the terminal clamps. Examine all wiring.

C.Miscellaneous

Check all thru-hull fittings for unobstructed water passage. Be alert for any deteriorated hoses and/or fittings below the water line which might fail in service and admit water.

Test the navigation lights.

Check all wiring for loose connections.

Check all switches and equipment for proper operation.

Check bilge blowers for proper operation. Turn on blowers and place hand over hull blower vent to make sure air is coming from vent.

Anchor lines and gear should be inspected and replaced if necessary.

Make sure the hull drain plug is in place and tight.

Clean bilge thoroughly if it was not done at lay-up.

Check all engine fluid levels.

8.6

192 Islander®

Image 68
Contents Baja Marine IslanderFor information call 1-865-971-6270 or fax Welcome This Page Intentionally Left Blank Introduction Manufacturer’s Certification Service, Parts and Repair for Your BoatHull Identification Number HIN About Your Express Limited Warranty Iii Ignition Protection Breakers and/or Fuses Speed changes you. TM Safety Safety LabelsFire Extinguishing System Legally Mandated Minimum Required EquipmentCarbon Monoxide Carbon Monoxide Monitor Lifesaving Equipment Load Capacity Additional Recommended Equipment for Safe OperationImpaired Operation Power Capacity StabilityGeneral Considerations Maintain ControlWeather Chart Your Course Skiing Water SportsSwimming Emergency Situations GeneralMedical Emergency Water RescueCollisions and Leaking FireFlooding, Swamping and Capsizing Safety Hotlines International RequirementsGrounding Propulsion, Control or Steering FailureEnvironmental Considerations Waste DisposalExcessive Noise Wake/WashNautical Terms Key to Symbols on Controls & Prints This Page Intentionally Left Blank California Residents Only This Page Intentionally Left Blank Passenger Locations General Boat ArrangementDocking/Lifting/Trailering 2 Hull Propellers Basic Boat Dimensions and Clearances MetricPropulsion System Horn General Deck LayoutGear Shift/Throttle Control Power Trim Unit and GaugeDescription of Major Controls Ignition Shutdown Switch Engine Alarm SystemImportant Gauges Tachometer and Hour MeterOil Pressure, Water Temperature, Voltmeter and Fuel Gauges Navigation and Anchor LightsThis Page Intentionally Left Blank Using Your Boat Pre-Launch, Launch and Post- Launch ChecklistTrailer Launching and Loading Fueling the BoatPassenger Instruction and Location BoardingPersonal Flotation Devices Starting the Engine To Start Engine Shifting to Drive the BoatStopping the Engine Steering SystemBilge & Underwater Gear BilgeBilge Pumps Drain PlugMaintenance and Service Engines and Stern DriveBilge Blowers Vibration and CausesPropeller Removal and Installation Impact to Stern DriveGear case Anti-Siphon Valve Inboard/Outboard Engine Only Fuel SystemFuel System Static Electricity and the Fuel System Fueling PrecautionsBefore and During Fueling Checklist After Fueling Checklist This Page Intentionally Left Blank Electrical Systems Electrical SystemsDirect Current DC BatteriesBreakers and/or Fuses Electrolytic Corrosion & Zinc AnodesFuse Panel Marine Electronic Cathodic Anti-corrosion System Mercathode Drive Pump OFF This Page Intentionally Left Blank Switch Panel Wire Information FIG REaR View FROnT ViewThis Page Intentionally Left Blank Options & Accessories Options & Accessories LocationsCanvas Canvas Care and MaintenanceAutomatic Fire Extinguisher System Option Depth Finder Optional HornSwim Platform w/ Ladder Optional Stereo SystemThis Page Intentionally Left Blank Interval Required Inspection, Service MaintenanceSummary Guide for Inspection, Service and Maintenance Summary Guide for Inspection, Service and Maintenance IntervalUseful Service Information Inspection, Service and Maintenance Protocol Bilge AreaWinterization Checklist for Boats Stored on Land BatteryiesTopside and Supplies Boat StorageFitting Out After Storage Fuel SystemsFuel System MiscellaneousPower Steering System Maintenance Security ConsiderationsBoat Systems Quick Reference ChecklistBoarding the Boat General Starting the Engine Quick Reference Checklist cont’d Departing Returning to PortIf the Engine Does Not Start Quick Reference Checklist cont’dSecuring the Boat After Market Equipment Checklist Maintenance Log Maintenance Log Cont’d Paint Cleaning Agents & Other Substances Care & RefinishingStains & Scratches Fiberglass & GelcoatPermanently Moored or Docked Boats Topside AreasAcrylic Plastic Sheeting Plastic Glass Canvas & Clear VinylExterior Upholstery Fabric Interior Upholstery FabricThis Page Intentionally Left Blank Index Index Islander

192 Islander specifications

The Baja Marine 192 Islander is an exceptional mid-range powerboat designed for both performance and leisure. This vessel stands out for its versatility, combining sporty characteristics with the ability to provide a comfortable family outing on the water.

One of the most notable features of the Baja 192 Islander is its sleek, aerodynamic hull design. With a length of 19 feet, this boat is crafted from high-quality fiberglass, ensuring durability and resilience. The deep-V hull helps to cut through waves with ease, providing a smooth ride even in choppy waters. This design not only enhances performance but also contributes to fuel efficiency, making it an economical choice for boaters.

Powering the Baja 192 Islander is typically a potent V8 engine, delivering impressive horsepower that ensures exhilarating acceleration. The boat is built for speed, appealing to those who crave thrills on the water. The engine compartment is engineered for easy maintenance, allowing boaters to spend more time enjoying their adventures rather than worrying about upkeep.

The cockpit of the Baja 192 Islander is designed with both function and comfort in mind. The helm features a well-arranged dashboard with easy-to-read gauges and intuitive controls, ensuring that the captain has complete command over the vessel. Upholstered seating provides comfort for both the driver and passengers, while stainless steel accents add a touch of elegance.

Another significant feature of the Baja 192 Islander is its ample storage options. The boat includes several compartments for personal belongings, gear, and fishing equipment, making it ideal for various activities such as day cruising or fishing excursions. The swim platform at the rear of the boat offers an easy entry point for swimming or water sports, enhancing the overall experience.

For entertainment, the Baja 192 Islander can accommodate sound systems that allow boaters to enjoy their favorite music while on the move. The layout also allows for social gatherings, making it a great choice for family outings or trips with friends.

In conclusion, the Baja Marine 192 Islander is a perfect blend of performance, comfort, and functionality. With its impressive speed, durable build, and thoughtful features, it remains a favorite among boating enthusiasts. Whether you are seeking adventure or relaxation, the Baja 192 Islander caters to all, making it an exceptional choice for a reliable and exciting boating experience.