Baja Marine 202 Islander Electrolytic Corrosion & Zinc Anodes, Breakers and/or Fuses, Fuse Panel

Page 53

Section 6 • Electrical Systems

!DANGER

GASOLINE VAPORS CAN EXPLODE

Use ONLY Marine-rated parts to replace such items as starters, distributors, alternators, generators, etc.

Do not use automotive parts for these components or any jumper cables because they are not ignition- protected and could cause a fire or explosion.

amperage and the rating is also marked on each fuse.

FUSE CONDITION (ATO TYPE FUSE) (FIG. 6.2.1)

GOOD FUSE

BLOWN FUSE

Protective terminal covers, such as rubber boots on electrical connections, must be in place when engine is operating or when working in the engine compartment.

Jumper cables are not ignition-protected. DO NOT USE jumper cables in the engine compartment. The engine compartment may accumulate dangerous explosive gasoline fumes/vapors and hydrogen gas from batteries being charged. A spark produced when connecting a jumper cable can cause an explosion.

C.Breakers and/or Fuses

!WARNING

Use of higher amperage fuses or breakers is a fire hazard.

Use fuses and breakers having the same amperage rating as the original or as specified.

If you need to replace a fuse or breaker, use only the same amperage and type as the original, and one that is rated for marine use. It is recommended that you carry spare fuses.

If a fuse or breaker is replaced with one of lower amperage, it will be insufficient to carry the electrical load of the equipment it is connected to and will cause nuisance fuse failure or breaker tripping.

If a breaker or fuse is replaced with a breaker or fuse of higher amperage, it will not provide adequate protection against an electrical malfunction and will create a fire hazard.

The fuses are color coded according to the

D.Fuse Panel

Your boat has an illuminated waterproof electronic switch pad to control lights, bilge pump and other accessories. The switch pad is connected to the fuse panel located under the dash. The fuse panel uses automotive type fuses to protect these accessories.

REPLACE ONLY WITH A FUSE OF THE SAME AMPERAGE and type. The amperage is marked on the side of the fuse.

2.Electrolytic Corrosion & Zinc Anodes

Electrolytic corrosion of metals on power boats can result in rapid and serious deterioration of metal parts. You must set a regular schedule and look for the possibility of electrolytic corrosion (the deterioration of metals due to dissimilar characteristics when placed in salt water). It is your responsibility to check for and replace parts damaged due to electrolytic corrosion.

To minimize electrolytic corrosion of the metals on your boat, zinc anode plates are provided on your boat to protect underwater hardware. Zinc, being much less "noble" than the copper-based alloys and aluminum used in underwater fittings, will deteriorate first and protect the other metals.

Stern drives are fitted with zinc anodes on their lower units (refer to your Engine Owner's Manual for their locations). If your boat is equipped a with Mercathode® system with the stern drive will not have zincs.

6.2

R

202 Islander®

Speed changes you. TM.

Image 53
Contents Islander Baja MarineFor information call 1-865-971-6270 or fax Welcome This page intentionally left blank Introduction Hull Identification Number HIN HIN NumberAbout Your Express Limited Warranty Iii Ignition Protection Breakers and/or Fuses Speed changes you. TM Safety Labels SafetyCarbon Monoxide Legally Mandated Minimum Required EquipmentFire Extinguishing System Carbon Monoxide Monitor Lifesaving Equipment Impaired Operation Additional Recommended Equipment for Safe OperationPropellers Power CapacityLoad Capacity Maintain Control StabilityGeneral Considerations Chart Your CourseWeather Skiing Water SportsSwimming General Emergency SituationsWater Rescue Medical EmergencyFire Flooding, Swamping and CapsizingCollisions and Leaking Safety HotlinesGrounding Propulsion, Control or Steering FailureFuel and Oil Spillage International RequirementsEnvironmental Considerations Excessive Noise Waste DisposalWake/Wash Nautical Terms Key to Symbols on Controls & Prints Baja Marine Corp This Page Intentionally Left Blank Docking /Lifting /Trailering Passenger Locations General Boat Arrangement2 Hull Propulsion System Basic Boat Dimensions and Clearances MetricGeneral Deck Layout HornGear Shift and Throttle Control Power Trim Unit and GaugeDescription of Major Controls Trim Tabs Trailer SwitchEngine Alarm System Ignition Shutdown SwitchImportant Gauges Tachometer and Hour MeterNavigation and Anchor Lights Oil Pressure, Water Temperature, Voltmeter and Fuel GaugesPre-Launch, Launch and Post- Launch Checklist Using Your BoatFueling the Boat Trailer Launching and LoadingPersonal Flotation Devices BoardingStarting the Engine Passenger Instruction and LocationStopping the Engine Shifting to Drive the BoatHydraulic Steering Steering SystemsPower Steering System Power SteeringBilge Bilge & Underwater GearFuel & Oil Spillage Drain PlugEngines and Stern Drive Maintenance and ServiceBilge Blowers Vibration and CausesImpact to Stern Drive Propeller Removal and InstallationGear case Anti-Siphon Valve Inboard/Outboard Engine Only Fuel SystemFuel System Static Electricity and the Fuel System Fueling PrecautionsBefore and During Fueling Checklist After Fueling Checklist This page intentionally left blank Electrical Systems Electrical SystemsDirect Current DC BatteriesFuse Panel Electrolytic Corrosion & Zinc AnodesBreakers and/or Fuses Marine Electronic Cathodic Anti-corrosion System Mercathode Ignition Switch Drive Pump This page intentionally left blank Switch Panel Wire Information FIG DC Wire Information FIG Options & Accessories Locations Options & AccessoriesCanvas Swim Platform w/ Ladder Optional Canvas Care and MaintenanceDepth Finder Optional HornExhaust Systems Stereo SystemInterval Required Inspection, Service MaintenanceSummary Guide for Inspection, Service and Maintenance Interval Summary Guide For Inspection, Service and MaintenanceUseful Service Information Bilge Area Inspection, Service and Maintenance ProtocolBatteryies Winterization Checklist for Boats Stored on LandTopside and Supplies Boat StorageFuel Systems Fitting Out After StorageFuel System MiscellaneousSecurity Considerations Power Steering System MaintenanceBoat Systems Quick Reference ChecklistBoarding the Boat General Starting the Engine Returning to Port General Quick Reference Checklist cont’d Departing GeneralIf the Engine Does Not Start Quick Reference Checklist cont’dSecuring the Boat After Market Equipment Checklist Maintenance Log Maintenance Log Cont’d Care & Refinishing Paint Cleaning Agents & Other SubstancesStains & Scratches Fiberglass & GelcoatTopside Areas Permanently Moored or Docked BoatsAcrylic Plastic Sheeting Plastic Glass Canvas and Clear VinylInterior Upholstery Fabric Exterior Upholstery FabricThis Page Intentionally Left Blank Index Index Islander