Baja Marine 230 manual Electrolytic Corrosion & Zinc Anodes, Breakers and/or Fuses, Fuse Panel

Page 54

Section 6 • Electrical Systems

!DANGER

GASOLINE VAPORS CAN EXPLODE

Use ONLY Marine-rated parts to replace such items as starters, distributors, alternators, generators, etc.

Do not use automotive parts for these components or any jumper cables because they are not ignition- protected and could cause a fire or explosion.

amperage and the rating is also marked on each fuse.

FUSE CONDITION (ATO TYPE FUSE) (FIG. 6.2.1)

GOOD FUSE

BLOWN FUSE

Protective terminal covers, such as rubber boots on electrical connections, must be in place when engine is operating or when working in the engine compartment.

Jumper cables are not ignition-protected. DO NOT USE jumper cables in the engine compartment. The engine compartment may accumulate dangerous explosive gasoline fumes/vapors and hydrogen gas from batteries being charged. A spark produced when connecting a jumper cable can cause an explosion.

C.Breakers and/or Fuses

!WARNING

Use of higher amperage fuses or breakers is a fire hazard.

Use fuses and breakers having the same amperage rating as the original or as specified.

If you need to replace a fuse or breaker, use only the same amperage and type as the original, and one that is rated for marine use. It is recommended that you carry spare fuses.

If a fuse or breaker is replaced with one of lower amperage, it will be insufficient to carry the electrical load of the equipment it is connected to and will cause nuisance fuse failure or breaker tripping.

If a breaker or fuse is replaced with a breaker or fuse of higher amperage, it will not provide adequate protection against an electrical malfunction and will create a fire hazard.

The fuses are color coded according to the

D.Fuse Panel

Your boat has an illuminated waterproof electronic switch pad to control lights, bilge pump and other accessories. The switch pad is connected to the fuse panel located under the dash. The fuse panel uses automotive type fuses to protect these accessories.

REPLACE ONLY WITH A FUSE OF THE SAME AMPERAGE and type. The amperage is marked on the side of the fuse.

2.Electrolytic Corrosion & Zinc Anodes

Electrolytic corrosion of metals on power boats can result in rapid and serious deterioration of metal parts. You must set a regular schedule and look for the possibility of electrolytic corrosion (the deterioration of metals due to dissimilar characteristics when placed in salt water). It is your responsibility to check for and replace parts damaged due to electrolytic corrosion.

To minimize electrolytic corrosion of the metals on your boat, zinc anode plates are provided on your boat to protect underwater hardware. Zinc, being much less "noble" than the copper-based alloys and aluminum used in underwater fittings, will deteriorate first and protect the other metals.

Stern drives are fitted with zinc anodes on their lower units (refer to your Engine Owner's Manual for their locations). If your boat is equipped a with Mercathode® system with the stern drive will not have zincs.

6.2

R

230 Sportfish® TE

Speed changes you. TM.

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Baja Marine For information call 1-865-971-6270 or fax Welcome This page intentionally left blank Introduction Service, Parts and Repair for Your Boat Hull Identification Number HINManufacturer’s Certification About Your Express Limited Warranty Iii Static Electricity and the Fuel System Speed changes you. TM Safety Safety LabelsLegally Mandated Minimum Required Equipment Carbon MonoxideUsing canvas curtains Operating with the bow high Lifesaving Equipment Additional Recommended Equipment for Safe Operation Impaired OperationPower Capacity Load CapacityPropellers Stability Maintain ControlChart Your Course WeatherGeneral Considerations Water Sports SwimmingSkiing Emergency Situations GeneralFire Medical EmergencyWater Rescue Flooding, Swamping and CapsizingGrounding Safety HotlinesCollisions and Leaking Propulsion, Control or Steering FailureInternational Requirements Environmental ConsiderationsFuel and Oil Spillage Waste Disposal Wake/WashExcessive Noise Nautical Terms Key to Symbols on Controls & Prints Baja Marine Corp This Page Intentionally Left Blank General Boat Arrangement Docking /Lifting /Trailering Passenger Locations2 Hull Basic Boat Dimensions and Clearances Metric Propulsion SystemGeneral Deck Layout General Deck Layout FIGPower Trim Unit and Gauge Description of Major ControlsGear Shift and Throttle Control Trailer Switch Trim TabsImportant Gauges Ignition Shutdown SwitchEngine Alarm System Tachometer and Hour MeterOil Pressure, Water Temperature, Voltmeter and Fuel Gauges Navigation and Anchor LightsUsing Your Boat Pre-Launch, Launch and Post- Launch ChecklistTrailer Launching and Loading Fueling the BoatBoarding Personal Flotation DevicesPassenger Instruction and Location Starting the EngineShifting to Drive the Boat Stopping the EngineSteering Systems Hydraulic SteeringPower Steering Power Steering SystemThis page intentionally left blank Fuel & Oil Spillage Bilge & Underwater GearBilge Drain PlugBilge Blowers Maintenance and ServiceEngines and Stern Drive Vibration and CausesPropeller Removal and Installation Impact to Stern DriveGear case Fuel System Fuel SystemAnti-Siphon Valve Inboard/Outboard Engine Only Fueling Precautions Before and During Fueling ChecklistStatic Electricity and the Fuel System After Fueling Checklist This page intentionally left blank Direct Current DC Electrical SystemsElectrical Systems BatteriesElectrolytic Corrosion & Zinc Anodes Breakers and/or FusesFuse Panel Marine Electronic Cathodic Anti-corrosion System Mercathode Ignition Switch Drive Pump Drive Pump with K-Plane Trim Tabs Twin FIG This Page Intentionally Left Blank Options & Accessories Options & Accessories LocationsHorn Canvas Care and MaintenanceCanvas Depth Finder OptionalExhaust Systems Stereo SystemHead Systems Requirements for OperatorsThis page intentionally left blank Required Inspection, Service Maintenance Summary Guide for Inspection, Service and MaintenanceInterval Summary Guide For Inspection, Service and Maintenance IntervalUseful Service Information Inspection, Service and Maintenance Protocol Bilge AreaTopside and Supplies Winterization Checklist for Boats Stored on LandBatteryies Boat StorageFuel System Fitting Out After StorageFuel Systems MiscellaneousPower Steering System Maintenance Security ConsiderationsQuick Reference Checklist Boarding the Boat GeneralBoat Systems Starting the Engine Quick Reference Checklist cont’d Departing General Returning to Port GeneralQuick Reference Checklist cont’d Securing the BoatIf the Engine Does Not Start After Market Equipment Checklist Maintenance Log Maintenance Log Cont’d Stains & Scratches Paint Cleaning Agents & Other SubstancesCare & Refinishing Fiberglass & GelcoatAcrylic Plastic Sheeting Plastic Glass Permanently Moored or Docked BoatsTopside Areas Canvas and Clear VinylExterior Upholstery Fabric Interior Upholstery FabricThis Page Intentionally Left Blank Index Index Sportfish TE

230 specifications

The Baja Marine 230 is a striking example of performance and style in the realm of high-performance boats. Renowned for its sleek design and aggressive aesthetic, this vessel is engineered for enthusiasts who crave exhilarating speed, agile handling, and a thrilling boating experience.

One of the standout features of the Baja Marine 230 is its impressive powertrain, which typically includes potent engine options that deliver remarkable horsepower. With a standard engine often exceeding 300 horsepower, it can achieve impressive top speeds that delight both novice and seasoned boaters. The boat's shape is meticulously crafted to reduce drag and enhance performance, ensuring that every dash across the water is thrilling.

The hull design of the Baja 230 is a notable characteristic, featuring a deep-V configuration that allows for excellent stability and a smooth ride even in choppy waters. This design minimizes the impact of waves, giving passengers a comfortable experience during high-speed cruising. Additionally, it is built to handle sharp turns and rapid accelerations, putting control firmly in the hands of the captain.

In terms of technology, the Baja Marine 230 often includes advanced instrumentation, with easy-to-read gauges and digital displays that provide real-time data on speed, fuel levels, and engine performance. This modern cockpit design not only enhances usability but also introduces an element of sophistication to the overall boating experience.

Comfort and luxury are not neglected in the Baja Marine 230. The cockpit typically features plush, ergonomically designed seating, accommodating guests while still leaving room for movement. Many models also come equipped with amenities such as high-quality sound systems, customizable lighting, and plenty of storage options, making it ideal for day trips and longer excursions alike.

Safety is paramount, and the Baja Marine 230 is built with sturdy construction materials that ensure durability and reliability on the water. Features such as non-slip surfaces, handrails, and well-placed grab handles contribute to a safe boating experience for all onboard.

Overall, the Baja Marine 230 stands out as a premium choice for fans of performance boating. Its combination of power, design, technology, and comfort makes it a formidable presence on the water, ready to deliver unforgettable adventures for those who dare to take command.
Top Page Image Contents