Graco 308-017 warranty Accessories

Page 22

ACCESSORIES

USE GENUINE GRACO PARTS AND ACCESSORIES

Must be purchased separately.

GROUNDING CLAMP 103-538

GROUND WIRE 208-950

7.6 m (25 ft) long,

1.5 mm@ (12 gauge)

BLEED-TYPE MASTER AIR VALVE

21 bar (300 psi) MAXIMUM WORKING PRESSURE 107-1413/4 npt(m) inlet x 3/4 npt(f) outlet 107-1421/2 npt(m) inlet x 1/2 npt(f) outlet

Relieves air trapped in the air line between the pump air inlet and this valve when closed.

AIR LINE FILTER

17.5bar (250 psi) MAXIMUM WORKING PRESSURE 106-1491/2 npt(f) inlet and outlet

106-1503/4 npt(f) inlet and outlet

AIR LINE LUBRICATOR

17.5bar (250 psi) MAXIMUM WORKING PRESSURE 214-8480.24 liter (8 oz) bowl capacity.

1/2 npt(f) inlet and outlet

214-8490.48 liter (16 oz) bowl capacity. 3/4 npt(f) inlet and outlet

AIR REGULATOR

21 bar (300 psi) MAXIMUM WORKING PRESSURE

104-266For President and Monark pumps.

0-18 bar (0-250 psi) Regulated Pressure Range; 1/2 npt(f) inlet and outlet.

206-197For Senator and Bulldog pumps.

0-9 bar (0-125 psi) Regulated Pressure Range; 1/2 npt(f) inlet and outlet.

AIR PRESSURE REGULATOR KITS

Kits include air regulator and gauge, bleed-type master air valve, manifold with swivel inlet, and attaching parts.

Model 205-712 (Shown)

For Senator and Bulldog Pumps 21 bar (300 psi) MAXIMUM WORKING PRESSURE

0-9 bar (0-125 psi) REGULATED PRESSURE RANGE

Model 223-815

0764

For Monark and President Pumps

 

21 bar (300 psi) MAXIMUM

 

WORKING PRESSURE

 

0-18 bar (0-250 psi)

 

REGULATED PRESSURE RANGE

 

PUMP RUNAWAY VALVE 215-362

12 bar (180 psi) MAXIMUM WORKING PRESSURE Shuts off air supply to the pump if the pump accelerates beyond the pre-adjusted setting due to an empty supply container, interrupted fluid supply to the pump, or exces- sive cavitation. 3/4 npt(f) inlet and outlet.

GROUNDED 19 mm (3/4 in.) BUNA-N AIR HOSE

12 bar (175 psi) MAXIMUM WORKING PRESSURE

Part No.

ID

Length

Thd. Size

208-610

19 mm (3/4”)

1.8 m (6 ft)

3/4 npt(m)

 

 

 

 

205-548

19 mm (3/4”)

4.5 m (15 ft)

3/4 npt(m)

 

 

 

 

208-611

19 mm (3/4”)

7.6 m (25 ft)

3/4 npt(m)

 

 

 

 

208-612

19 mm (3/4”)

15.2 m (50 ft)

3/4 npt(m)

 

 

 

 

GROUNDED 13 mm (1/2 in.) BUNA-S AIR HOSE 12 bar (175 psi) MAXIMUM WORKING PRESSURE

Part No.

ID

Length

Thd. Size

205-418

13 mm (1/2”)

1.8 m (6 ft)

1/2 npt(m)

 

 

 

 

205-216

13 mm (1/2”)

4.5 m (15 ft)

1/2 npt(m)

 

 

 

 

205-273

13 mm (1/2”)

7.6 m (25 ft)

1/2 npt(m)

 

 

 

 

208-594

13 mm (1/2”)

15.2 m (50 ft)

1/2 npt(m)

 

 

 

 



Image 22
Contents INSTRUCTIONS-PARTS List Table of ContentsSpray Tip/Nozzle Safety General SafetySpray Gun/Dispensing Valve Safety Devices Pressure Relief ProcedureSystem Pressure Flushing SafetyGrounding Fluid CompatibilityTypical Installation Main Fluid Hose Fluid Whip HoseSystem Accessories InstallationGrounding Packing Nut/Wet-Cup OPERATION/MAINTENANCEStarting and Adjusting the Pump Flushing the PumpShutdown and Care of the Pump AIR Motor PlateTroubleshooting Chart Problem Cause SolutionReconnecting the Displacement Pump ServiceDisconnecting the Displacement Pump Required ToolsDisplacement Pump Service DisassemblyDetail of Piston Intake Check Valve Reassembly Refer to Fig Throat Packing Detail 14  Parts Drawings Parts Lists HOW to Order Parts Parts Drawing and List107 101 111 102 Model 222-769 Shown Model 222-778 Shown Model 222-790, Series B Displacement Pump Parts DrawingParts List Service InformationAccessories Fluid Drain Valve Cart Accessory KITNylon Fluid Hose Fluid Regulator Floor Stand KITTechnical and Performance Data Model PtfeRatio 26  Ratio Quiet Senator Air Motor 28  Ratio Quiet Bulldog Air Motor Dimensional Drawing Mounting Hole Layouts Model 222-768 President Pump Model 222-770 Monark PumpGraco Warranty and Disclaimers Important Phone Numbers