Eagle Electronics 320 manual Transom

Page 19

B. Two-piece bracket: Once you determine the correct position for the ratchets, assemble the transducer as shown in the figure in step 2B. Don't tighten the lock nut at this time.

4.Drilling mounting holes.

Hold the transducer and bracket assembly against the transom. The transducer should be roughly parallel to the ground. The trans- ducer's centerline should be in line with the bottom of the hull. Don't let the bracket extend below the hull!

Mark the center of each slot for the mounting screw pilot holes. You will drill one hole in the center of each slot.

Drill the holes. For the one-piece bracket, use the #29 bit (for the #10 screws). For the two-piece bracket, use the #20 bit (for the #12 screws).

Transom

Transom

Position transducer mount on transom and mark mounting holes.

Side view shown at left and seen from above at right.

5.Attaching transducer to transom.

A. One-piece bracket: Remove the transducer from the bracket and re-assemble it with the cable passing through the bracket over the bolt as shown in the following figures.

For single-frequency Skimmer, route cable over bolt and through bracket. Side view shown at left and seen from above at right.

15

Page 18 Page 20
Image 19
Page 18 Page 20
Contents FishMark 320 SeaFinder 320DF Page Table of Contents Fish I.D. Fish Symbols & Depths How this manual can get you out on the water, fast Read Me FirstGeneral Figuration and installation, bottom composi How Sonar Works How to use this manual typographical conventionsPage Page Preparations Transducer InstallationShoot-through hull installations Single-frequency transom installationsDual-frequency transom installations Single-frequency trolling motor installationsGood and poor transducer locations Transom Transducer centerline Hull bottom Dot Transom Transducer Assembly and MountingTransducer Alignment lettersAlignment PositionsRatchets Bolt Bolt Flat washer Lock washer NutMetal Nut Washer Rubber WashersTransom Hull BottomFlat-bottom hull Deep-vee hull Internal tooth washer TMB-S bracket Bolt Nut Flat washer Full fish arch Proper transducer angle Partial fish archesTransducer aimed Too far backSHOOT-THRU-HULL Preparation Transducer location High speed Trolling speed Spread epoxy here Sand this surface Speed/Temperature SensorsRear view Sonar unitGood location Transom Bottom of hull Power ConnectionsOptional power off switch for Ducer socket Sonar unit Rear view Power/transPower c able Accessory Transducer Cable Mounting the Unit Bracket, In-Dash or PortableFront 173.9 23.4 137.9 157.9 Millimeter 56.9 Inch 72.9113.5 Millimeters Inches 146.5Face Cover Cell batteryKeyboard Basic Sonar OperationPower/lights on and off Menus Main Menu Commands Sonar Menu Commands Pages Sonar Page, showing full sonar chart mode. bar graph Page Basic Sonar Quick Reference Sonar Operations Page Important Tip To Restore Factory SettingsPage Page Sonar Options & Other Features Alarms To adjust and turn on the deep alarm To adjust and turn on the shallow alarmTo adjust and turn on the zone alarm Brightness To turn the fish alarm onCalibrate Speed Chart SpeedDepth Cursor ContrastDepth box Depth Range Automatic To switch to Manual Depth RangeDepth Range Manual Bar graph Fish I.D. Fish Symbols & DepthsFasTrack To turn Auto Depth Range on againPage Page Press → ↓ to Fish ID Depthsentexitexit Symbols with FishTrack depthsFishTrack FishRevealPage Fish Not Visible Fish arch Fish arches Frequency Change Transducer Frequency SeaFinder 320DF onlyGrayline Grayline Hard Bottom Muddy bottom Hard Fish nearHard Muddy bottom bottom Grayline HyperScrollNoise Rejection Overlay DataTo change displayed data font size To turn off displayed dataPing Speed & HyperScroll Page Pop-up Help Reset OptionsScreen Contrast and Brightness Reset Water DistanceSensitivity & Auto Sensitivity Page Set Keel Offset Press MENUMENU↓ to SET Keel Offsetent Software Version Information Set LanguagePress MENUMENU↓ to Software Infoent Sonar Chart Display Options Sonar Color ModePage Page Customizing the Digital Data/Chart Screen Sonar Simulator Stop ChartPress ↓ or ↑ to select clarity levelEXITEXITEXIT Surface ClarityZoom & Zoom Bar Units of MeasureZoom Pan Page Troubleshooting Page Noise Page Page Page Supplemental Material How to Obtain Service… Accessory Ordering Information for all countries Visit our web site
Related manuals
Manual 200 pages 25.32 Kb Manual 128 pages 61.27 Kb

320 specifications

Eagle Electronics 320 is a state-of-the-art device that has transformed the landscape of consumer electronics. Designed for those who demand both performance and precision, this innovative product integrates several cutting-edge technologies to deliver a seamless user experience.

One of the standout features of the Eagle Electronics 320 is its advanced touchscreen display, which boasts vibrant colors and high resolution, making it ideal for multimedia applications. With a responsive interface, users can navigate through menus and applications effortlessly. The display also incorporates anti-glare technology, ensuring visibility even in bright environments.

In terms of connectivity, the Eagle Electronics 320 is equipped with multiple options, including Bluetooth 5.0, Wi-Fi 6 compatibility, and NFC capabilities, allowing users to connect with other devices quickly and efficiently. This extensive connectivity makes it perfect for both personal and professional use, enabling easy file sharing and seamless device pairing.

The Eagle Electronics 320 is powered by an impressive multi-core processor that provides fast and efficient performance. Whether running demanding applications or multitasking, this device excels in speed and responsiveness. Coupled with ample RAM, users can enjoy smooth operation without the frustrating lags often associated with lower-end devices.

Another key feature is its robust battery life. The Eagle Electronics 320 has been engineered to last, providing users with extended usage time without frequent recharging. This is especially beneficial for professionals on the go or anyone who relies on their device for long periods.

Regarding audio, the Eagle Electronics 320 doesn't disappoint. It features superior sound technology, including noise cancellation and enhanced bass, ensuring an immersive audio experience whether watching movies, listening to music, or engaging in video calls.

Security is a top priority with the Eagle Electronics 320. It comes with advanced encryption technologies and biometric authentication options, such as fingerprint scanning and facial recognition, ensuring that user data remains protected.

In summary, the Eagle Electronics 320 is a remarkable device that brings together modern design, powerful performance, and innovative features. Its impressive technologies make it suitable for a wide range of applications, appealing to both tech enthusiasts and everyday users alike. Whether for work or play, this cutting-edge electronics marvel stands out as a reliable companion in today’s fast-paced digital world.
Top Page Image Contents