Furuno 1933C, 1943C, 1833C, 1823C Connecting remote display, How to connect remote signal cable

Page 72

4.2.3Connecting remote display

The FURUNO Display unit FMD-811, MODEL1832 or GD-280/380, etc. can be connected to the NavNet display as remote display. To interconnect them, use a cable attached with or set as option for the remote display. For the network system consists of some units, connect the remote display cable to the one selected as radar source. Also, the optional EMI core (Type: E04R241336A, Code No.:000-146-335) should be attached to the remote display cable to prevent a noise.

1.Unscrew 15 binding screws (M3x10, w/nylon washer) and seven connector nuts to remove the display unit cover.

2.Pass the signal cable for remote displaying through the hole at the rear of the display unit cover and the saddle on the POWER Board, and then connect the XH connector (8P) of the signal cable to J109 on the SPU Board. If your remote signal cable has the ground wire, pass it outside of the cover and fix it with the screw shown below.

3.Reassemble the display unit referring to the illustration on page 4-3.

4.Attach the EMI core (option) to the remote display cable at the closed position to the display unit.

Connector nut (large) 1 pc.

Binding screws

(M3x10, w/nilon washer) 15 pcs.

Connector nut (for 24P) 1 pc.

Connector nut (small) 5 pcs.

Use one of these screws to fix the ground wire of the remote signal cable.

Other equipment's remote signal cable

J109

Attach EMI core closely

 

Saddle

to the display unit.

How to connect remote signal cable

4-8

Image 72
Contents Back 00080919906 Safety Instructions Table of Contents Standard supply IiiOptional supply NTSC/PALSystem Configurations NavNet system GD-1900C NavNet system, three-unit connection NavNet system, two-unit connectionViii Mounting Tabletop, overhead mounting methodTabletop, overhead mounting Tabletop, overhead mounting of display unitFlush mounting Fixing screw, side viewFlush mounting of display unit Typical antenna unit placement on sailboat and powerboat Mounting of Antenna Unit for MODEL1833CAntenna unit Antenna unit, cover removedHow to fasten the radome base to the mounting platform Wiring and final preparationAntenna unit, inside view Signal cable, antenna unit side RF unitHow to attach EMI core How to position the radome coverMounting bracket contents Mounting bracketHow to assemble and mount the optional mounting bracket Assembling the mounting bracketFastening antenna to mounting bracket Mounting of Antenna Unit for MODEL1933C/1943C/1953C Fastening the Radiator to the Radiator Bracket Coating the antenna with silicone sealantFastening the radiator bracket to the antenna unit chassis Mounting of antenna unit Outside fixing holesLocation of rubber mat How to fasten antenna unit to mounting platform Fixing the antenna unit chassisGround Fixing holes inside antenna unit Antenna unit chassis, upper chassis separatedConnecting the Signal Cable Passing the signal cable through the cable gland assemblyAntenna unit chassis, cover opened How to fix signal cable in cable gland Torque 9.8 ±0.1 N .m Mounting of Power Supply Unit for Model 1953C Power supply unitMounting of Antenna Unit for Model 1823C Mounting considerationMounting antenna unit of Model 1823C Antenna unit, showing location of mounting hardwareHow to fasten the base to platform Snap holder Remove and discard the packing materialGND Antenna unit, inside view Location of EMI coreHow to pass the rotation detector cable EMI core, putting into core caseMounting the optional mounting bracket Antenna unit, clamping the rotation detector cableStandard Wiring Display unit, rear viewWaterproofing cap and connector nut, sectional view 12-24 VDCDJ-1 Ground terminalConnecting GP-310B/320B to Data 2 port Network portExternal Buzzer OP03-136, option Connection How to Connect with PC MJ-A7SPF0007-050 cable connection for PCWiring of Power Supply Unit MODEL1953C only Power supply unit, cover removedReplacement of the fuse Connection of CU-200 option HUBHow to Access to Installation Menu How to access the Installation menuInstallation setup menu Network Setup Menu Network Setup menuHost name window Contents of Network setup menu NavNet equipment default settingsRadar Setup Menu Radar setup menuTuning Antenna TypeAntenna tuning Tuning setup menuExamples of improper and correct sweep timing Timing adjust setting menu Timing adjustment setting displayVideo adjustment setting window Heading Adjust Heading adjustment setting displayMain bung suppression setting window Radar antenna height setting windowSTC curve setting window Heading data setting windowNav setup menu Checking Magnetron Heater VoltageNavigation Data Source Position Source Furuno BB GPS ALL GPS setup menu Antenna height windowContents of GPS sensor settings menu On nextContents of GPS sensor settings menu con’t Setting up Data Ports DATA1, DATA2, Data 4 Port menusContents of Data 1 and DATA2 Port menus Nmea data sentencesRemote Controller Setting Contents of Data 4 Port menuGeneral Setup menu Remote Display Setting Select I/R Remote windowThis page is intentionally left blank ARP-11 contents ARP Kit ARP-11Removing the display unit cover Dismounting the Power Board BoardOrder of fastening screws Connecting video equipment NTSC/PAL Interface kit contents3C-2V cable, sectional view NTSC/PAL Interface Board attachmentCable ties attachment Display unit, passing the PIP cableHow to connect 15SDS/XHP10-005 Necessary parts for external monitorConnecting remote display How to connect remote signal cableAttaching more than two units Mounting the Memory Card Interface Unit MJ-A6SPF/TM11APDesktop mount This page is intentionally left blank Packing List RDP-138/139 E Page Packing List Page Page Page Page Page PSU-005 Page Page Hatai Page Page Page Hatai Page Page Page Hatai Model 1823C Marine Radar Model 1953C Hatai
Related manuals
Manual 260 pages 55.31 Kb Manual 251 pages 25.79 Kb

1823C, 1833C, GD-1900C, 1933C, 1953C specifications

Furuno is a well-respected name in marine electronics, renowned for producing high-quality navigation and fish-finding equipment. Among their product line, the Furuno 1943C, 1953C, 1933C, GD-1900C, and 1833C stand out as reliable radar systems, providing exceptional performance and advanced features for both commercial and recreational vessels.

The Furuno 1943C is a powerful 12 kW radar system, boasting a 10.4-inch monochrome display with a user-friendly interface. It is equipped with digital signal processing (DSP) technology that enhances target detection and resolution. The 1943C offers superior target tracking capabilities, even in challenging weather conditions. Its patented Auto Gain Control ensures that small targets are not lost in clutter, making it a favorite among serious navigators.

Moving on to the Furuno 1953C, this model has an impressive 12 kW output and features a high-resolution 15-inch color display. It integrates advanced features such as Automatic Radar Plotting Aid (ARPA) for tracking multiple targets simultaneously, increasing situational awareness and safety on the water. Additionally, the 1953C offers a range of presentation modes, allowing users to customize the display to their specific needs.

The Furuno 1933C is a compact yet efficient radar solution with a 6 kW output and a 10.4-inch monochrome display. This system is highly regarded for its reliable performance and ease of use. Its user-friendly interface makes navigation simple, while features such as Target Analyzer and Echo Trails aid in identifying potential hazards, ensuring safe passage through busy waterways.

The Furuno GD-1900C combines chartplotting and radar in a single unit. With a 10.4-inch color display, it provides clear visuals of radar data as well as navigation charts. The GD-1900C supports various chart formats, including C-MAP and Navionics, allowing boaters to access detailed navigational information. This system is especially useful for those who need both radar and chartplotting capabilities in a space-saving design.

Lastly, the Furuno 1833C is a versatile radar system with a 4 kW output and a 7-inch color display, catering to smaller vessels. It features Furuno's advanced technology, such as a built-in GPS receiver and the ability to overlay radar data on electronic charts. This model is ideal for recreational boaters seeking an affordable yet feature-rich radar solution.

In summary, Furuno’s range of radar systems, including the 1943C, 1953C, 1933C, GD-1900C, and 1833C, demonstrates the brand’s commitment to quality and innovation in marine technology. Each unit incorporates advanced features tailored to meet the diverse needs of boaters, ensuring safe and efficient navigation on the water.