JBL AVR480 Video 2 Video Input Connect this, Video 2 Audio Inputs Connect, DVD S-Video Input

Page 11

Video 2 Video Input: Connect this

jack to the PLAY/OUT composite video jack on a second VCR or other video source.

Video 2 Audio Inputs: Connect

these jacks to the PLAY/OUT audio jacks on a VCR or other video source.

Video Monitor Outputs: Connect

these jacks to the composite and/or S- Video input of a TV monitor or video pro- jector to view the output of any video source selected by the receiver’s video switcher.

If you would like to make an S-Video recording from the source connected to

the DVD S-Video Input

, you may use

the Video Monitor Output

S-Video

jack when connected to a compatible

recording device. However, you will not be able to monitor the video signal from your video display.

TV Audio Inputs: Connect these jacks to the Audio Out jacks on a TV or other video source.

Surround Speaker Outputs: Connect these outputs to the matching + or – terminals on your left and right sur- round speakers. When making speaker connections always make certain to maintain correct polarity by connecting the colored (+) terminals on the AVR480 (see chart above) to the red (+) terminals on the speakers and the black (–) termi- nals on the AVR480 to the black (–) termi- nals on the speakers. (See page 15 for more information on speaker polarity.)

Front/Center Speaker Outputs: Connect these outputs to the matching + or – terminals on your front/center speak- ers. When making speaker connections, always make certain to maintain correct polarity by connecting the colored (+) ter- minals on the AVR480 (see chart above) to the red (+) terminals on the speaker and the black (–) terminals on the AVR480 to the black (–) terminals on the speakers. (See page 15 for more information on speaker polarity.)

AC Power Cord Jack: Connect the AC power cord to this jack when the installation is complete. To ensure safe operation, use only the power cord sup- plied with the unit. If a replacement is required it must be of the same type and capacity.

Depending on the electrical requirements in your area or the wiring in your home, the power cords included with your AVR may not be the correct ones, and you may need to contact your local JBL distributor to obtain the correct power cord.

AM Antenna: Connect the AM loop antenna supplied with the receiver to these terminals. If an external AM antenna is used, make connections to the AM and GND terminals in accordance with the instructions supplied with the antenna.

FM Antenna: Connect the supplied indoor or an optional external FM antenna to this terminal.

Region Selector: Select the position corresponding to the country in which the AVR will be used (C, S or K) so that the video standard and the FM tuner’s fre- quency increments will be correct. (See page 31 for more information on setting the Region Selector .)

IMPORTANT NOTE: Any adjustments made to the Region Selector will not take effect unless the unit is first fully turned off by pressing the Main Power Switch 1 until it pops out and the word “OFF” appears on the top of the button.

11

Image 11
Contents AVR480 Introduction Important Safety InformationDeclaration of Conformity AVR480 AUDIO/VIDEO ReceiverWalked on or pinched, particularly at An electrician for replacementMultiple Digital Inputs and an Output Description and FeaturesIntroduction Unpacking Important Safety InformationSafety Information ‹/›Selector Buttons Set Button Delay Button Digital Input SelectorFRONT-PANEL Controls Optical and Coaxial Digital $ Volume Control Turn this knobFRONT-PANEL Information Display Speaker/Channel Input IndicatorsPreset Number/Sleep Timer P Preset Indicator Logic 7 Mode IndicatorsPage Optical Digital Audio Input REAR-PANEL ConnectionsCoaxial Digital Audio Output Coaxial Digital Audio InputDVD S-Video Input Video 2 Video Input Connect thisVideo 2 Audio Inputs Connect Video Monitor Outputs ConnectProgram Indicator This three-color Remote Control FunctionsAfter the Delay Button has been pressed Page Speaker Outputs to the respective speakers Installation and ConnectionsPanel. Note that the Optical Video Connection Notes Video 1 Output JacksVideo source to the Video Video 3 # Input Jacks DVD Video Input JacksMeters 6 feet behind the rear of the seating area Speaker PlacementSpeaker Selection Input Setup Settings to Be Made With Each Input UsedSystem Configuration To obtain the correct power cord for your areaInformation Display K Press the Set Button E Speaker SetupPress the Speaker Button Ô FNT Spkr will appear in the MainIcons in the Speaker/Channel Input Surround SetupSurround Mode Selector Button Buttons C % so that SUB LFE appears in the displaySdelay will appear in the Main Configuring Global SettingsDelay Settings To set the delay time, follow these stepsDisplay K. Press the ⁄/¤ Buttons Night Mode SettingsOutput Level Adjustment Adjust the Volume Control $Appears in the Main Information Until the desired surround modeOperation Basic OperationSource Selection 11 listening modes are available on the AVR480 Surround Mode SelectionUp/Down buttons Mute ButtonInput on the rear panel Digital Audio PlaybackDolby Digital Optical or Coaxial Input on the rear panel Digital Status IndicatorsSelecting a Digital Source PCM Audio PlaybackSurround Mode Chart Video 1 Outputs Night ModeWhen a Dolby Digital or DTS source Tape RecordingDisplay Brightness Memory BackupUsing the Volume Control $ Tuner Operation Auto Search Method Programming the Product CodesProgramming the Remote Direct Code EntryProgrammed Device Functions Macro ProgrammingTransport Control Punch-Through Volume Punch-ThroughChannel Control Punch-Through AVR480 Function List Direct Preset UpPreset Down Tape VCR VID1,3Device TV Hinari Saba Device VCR 054 076 154 047148 155 176 050 054 073012 044 047 090 141044 083 090 094 104 108 131 149 155Device CD Device DVD Device SAT Device Cable Setup Code NumberDevice Tape Troubleshooting Guide Processor ResetAVR480 Specifications Page
Related manuals
Manual 4 pages 51.39 Kb