Axiom Audio Axiom 61 manual To Assign the Rotary Encoders, Endless Data Method Increment Decrement

Page 20

Axiom Line User Guide

In order to program one of these methods to the rotary encoders on your Axiom, you should assign the MIDI controllers given below:

MIDI CC

Endless Data Method

Increment

Decrement

 

 

 

 

145

Program Change Increment/Decrement

 

 

 

 

146

2’s Complement from 64 / Relative (Binary Offset)

065 to 127

063 to 000

 

 

 

 

147

2’s Complement from 0 / Relative (2’s Complement)

001 to 64

127 to 065

 

 

 

 

148

Sign Magnitude / Relative (Signed Bit)

065 to 127

001 to 063

 

 

 

 

149

Sign Magnitude / Relative (Signed Bit 2)

001 to 063

065 to 127

 

 

 

 

150

Single Value Increment/Decrement

096

097

 

 

 

 

151

RPN Increment/Decrement Message

096 then 000 to 127

097 then 000 to 127

 

 

 

 

152

NRPN Increment/Decrement Message

096 then 000 to 127

097 then 000 to 127

 

 

 

 

To Assign the Rotary Encoders:

49- and 61-note versions:

<Select the rotary encoder as explained in section 2.

<Press the Ctrl Assign button. The LCD shows the encoder’s current controller assignment.

<Decide which endless data method you want from the table above, and enter its MIDI CC number using the numeric keypad.

<Press Data 2. The LCD display flashes the encoder’s current data parameter.

<Enter the MIDI controller number from Appendix C that you want. (Note that the range in this case is 0-127, not 0-131.)

<The encoder will now transmit increment/decrement messages on the MIDI controller you have set.

25-note version:

<Select the rotary encoder as explained in section 2.

<Press the Advanced button.

<Press the Ctrl Assign key. The LCD will show the encoder’s current controller assignment.

<Decide which endless data method you require from the table above, and enter its MIDI CC number using the numeric data entry keys.

<Press the Enter key to confirm.

<Press the Advanced button again.

<Press the Data 2 key.The LCD display will show the encoder’s current data parameter..

<Enter the MIDI controller number from Appendix C that you want. (Note that the range in this case is 0-127, not 0-131.)

<Press the Enter key to confirm.

<The encoder will now transmit increment/decrement messages on the MIDI controller you have set.

19

English

Image 20
Contents Axiom Table of Contents Axiom Line User Guide Introduction What’s in the Box?Axiom Keyboard Overview About This ManualTop Panel Overview Back Panel Overview Control Definitions Getting StartedAxiom Keyboards Overview Setup Driver Installation ProcedureUsing The Axiom with Your Software Midi ConnectionsPower Supply Basic Midi Control From Your AxiomAxiom 49 And 61 Functions Numeric Keypad Axiom 25 Functions EnglishFunction Section Function IndexWhite Keys Black Keys Numeric Data Entry Keys Curve Fixed Velocity Value KeyboardVelocity Curve To access all 11 available octaves from your keyboard To change the velocity curveOctave TransposeMidi Channel Program and Bank ChangesTo set the channel of your keyboard To send a program changeEffect Control Number Midi Controller MessagesTo send a bank change Extra Messages 128 To Programming the Controls on Your AxiomMethod Programming a controlReset PanicAdvanced Features Midi ControllersLimiting the Range of Controllers Axiom Control Controller Definition TableTo store all of the current control settings on your Axiom Recollection and Storage of Your Control SetupsDrawbar Mode To recall any memory you have stored Control GroupsStoring Your Presets on a Computer Device IDHow To Avoid Jumping Parameters Rotary EncodersMute NullTo Assign the Rotary Encoders Endless Data Method Increment DecrementPressure Pads Acceleration CurvesTo select the acceleration curve Sample/Loop Triggers With Midi NotesDrum Pattern Composition Sample/Loop Triggers with Midi Controller Messages To change the velocity curve for the pads Pressure ControlPad Curve Setting the Vel. Lock parameters as follows Controlling Several Devices at the Same TimeVelocity Lock ZonesTo enable/disable any zone Activating/Deactivating ZonesZone Channel To assign the channel of a zoneMore About Program, Bank LSB And Bank MSB Zone RangeTo set the range of a zone Individual Channel Assignments of Controls To assign the transmit channel for a controlGroup a Controls Setting Toggle Values for the Buttons Setting up a toggle effectSetting up an alternating value effect Example of Control FunctionalityNumber MMC Command Assigning MMC Messages to a ButtonAssigning RPN/NRPN Messages to a Fader or Encoder To assign RPN or Nrpn numbersUsage Examples Midi Out from USB FunctionTo control Midi out from USB mode Recording Your Performance On a SequencerProgram & Bank Changes Explained Midi Messages ExplainedControlling a Sound Module from the Computer RPN/NRPNs Explained SysEx ExplainedTroubleshooting Technical Info Warranty Terms and RegistrationWarranty Terms Warranty Registration English Appendix a Midi Implementation Chart AppendicesAppendix B Useful Midi Data Tables B1 General Midi Instruments Program Change NumbersB2 General Midi Note Numbers OctaveB3 Roland GS And Yamaha XG Nrpn Messages B4 General Midi Drums Note assignmentsB5 GM2 Chorus Types B6 General Midi Drums Note assignmentsAdditional Messages Channel Mode MessagesAppendix C General Midi Controller Numbers Midi CCs Description Data Midi CC Appendix F Assignable Controller Numbers to Rotary Encoders Appendix G Assignable Controller Numbers to Pressure Pads This table only applies to the pressure Pads on your AxiomAppendix H Hexadecimal Conversion Chart Hexadecimal value Decimal valueAppendix I Factory Presets How to use the Axiom with Ableton Live Preset 4 GForce MinimonstaPreset 5 Way Out Ware TimewARP Preset 6 Wizoo Darbuka/LatigoPresets 7 to 12 Propellerhead Reason Presets 17 and 20 Ableton Live / Unassigned Midi controllersAudio USA