Pioneer VSX-1015TX operating instructions Setting the Acoustic Calibration EQ automatically

Page 43

The System Setup menu

When it sounds like the delay settings are matched up, press ENTER to confirm and continue to the next channel.

•For comparison purposes, the reference speaker will change depending on which speaker you select.

•If you want to go back and adjust a channel, simply

use

(cursor up/down) to select it.

4 When you're finished, press RETURN.

You will return to the Manual MCACC setup menu.

Acoustic Calibration EQ

Acoustic Calibration Equalization is a kind of room equalizer for your speakers (excluding the subwoofer). It works by measuring the acoustic characteristics of your room and neutralizing the ambient characteristics that can color the original source material. This provides a ‘flat’ equalization setting. If you’re not satisfied with the automatic adjustment, you can also adjust these settings manually to get a frequency balance that suits your tastes.

Setting the Acoustic Calibration EQ automatically

If you have already completed Automatically setting up for surround sound (MCACC) on page 11, ALL CH ADJUST and FRONT ALIGN (below) should already be set.

Therefore, if you want to adjust your settings manually, you can skip to Setting the Acoustic Calibration EQ manually below.

1Select ‘EQ AUTO Setting’ from the Manual MCACC setup menu.

3.MANUAL MCACC

 

3c.EQ AUTO Setting

[ a .Fine Ch Level

]

 

[ b .Fine Ch Distance

]

 

[

c .EQ AUTO Setting

]

Please Wait

[

d .EQ Data Copy

]

[ e .EQ CUSTOM1 Adjust

]

Caution!!

[ f .EQ CUSTOM2 Adjust

]

[ g .EQ Data Check

]

Test tone is

 

 

 

output loudly.

 

 

 

Return:Cancel

•Make sure the microphone is connected.

•If you’re using a subwoofer, it is automatically detected every time you switch on the system. Make sure it is on and the volume is at the middle position.

•See Other problems when using the Auto MCACC Setup on page 13 for notes regarding high background noise levels and other possible interference.

06

2 Wait for the Auto MCACC Setup to finish.

3c. EQ AUTO Setting

 

 

3c. EQ AUTO Setting

 

 

Now Analyzing•••

 

 

Now Analyzing•••

 

 

 

 

 

 

 

 

 

 

Environment Check

 

 

Surround Analyzing

 

 

Ambient Noise

[

]

Channel Level

[

]

Microphone

[

]

Acoustic Cal EQ

[

]

Speaker YES/NO

[

]

 

 

 

 

Return:CancelReturn:Cancel

As the receiver outputs test tones, the frequency balance is adjusted automatically for the following settings:

•ALL CH ADJUST – A ‘flat’ setting where all the speakers are set individually so no special weighting is given to any one channel.

•FRONT ALIGN – All speakers are set in accordance with the front speaker settings (no equalization is applied to the front left and right channels).

You will return to the Acoustic Cal EQ setup menu after the Acoustic Calibration Equalization is set.

Copying your Acoustic Calibration EQ settings

If you want to manually adjust the Acoustic Calibration EQ (see Setting the Acoustic Calibration EQ manually below), we recommend copying the ALL CH ADJUST or the FRONT ALIGN settings from the EQ AUTO setup above (or from Automatically setting up for surround sound (MCACC) on page 11) to one of the custom settings. Instead of just a flat EQ curve, this will give you a reference point from which to start.

1Select ‘EQ Data Copy’ from the Manual MCACC setup menu.

3.MANUAL MCACC

 

[ a .Fine Ch Level

]

[ b .Fine Ch Distance

]

[ c .EQ AUTO Setting

]

[

d .EQ Data Copy

]

[

e .EQ CUSTOM1 Adjust

]

[ f .EQ CUSTOM2 Adjust

]

[ g .EQ Data Check

]

2Select CUSTOM1 or CUSTOM2 then use the (cursor left/right) buttons to select the setting you want to copy.

3d. EQ Data Copy

 

3d. EQ Data Copy

 

TO

 

FROM

 

TO

 

FROM

 

CUSTOM1

[

 

]

CUSTOM1

[

 

]

CUSTOM1

ALL CH ADJ.

CUSTOM2

[

CUSTOM2

]

CUSTOM2

[

CUSTOM2

]

Start Copy

 

[ OK

]

Start Copy

 

[ OK

]

•You can also copy from one custom setting to another. For more on the ALL CH ADJUST and FRONT ALIGN settings, see Setting the Acoustic Calibration EQ automatically above.

43

En

Page 42 Page 44
Image 43
Page 42 Page 44
Contents VSX-1015TX Information to User Wash hands after handlingImportant Safety Instructions Contents Additional information Other SettingsControlling the rest of your system Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterBefore you start Ventilation Installing the receiverLoading the batteries Listening to Surround Sound Minute guide02 5 minute guide Chapter Introduction to home theaterConnect your speakers Minute guide02 5 minute guide Enter Make sure ‘Normal SB’ is selected then pressFollow the instructions on-screen Other problems when using the Auto Mcacc Setup Checking the settings on your DVD or other playerPlaying a source Connecting up Chapter Connecting upAbout cable types About the video converter Connecting upCD recorder DVD or LD player CD player Connecting up Connecting digital audio componentsConnecting multichannel analog components Connecting up Connecting analog audio componentsTip Connecting to the front panel video terminal Connecting up Connecting video componentsVideo Camera AM loop antenna Connecting up Connecting antennasUsing external antennas FM wire antennaSpeaker terminals Connecting up Connecting the speakersTighten terminal Hints on speaker placement Overhead view of speaker setupAC outlet Connecting upTHX speaker system setup View of 7.1 channel speaker setupOperating other Pioneer components Power cord cautionFront panel Listening Mode SelectControls and displays Controls and displays ChapterControls and displays Controls and displays Display Sleep StereoMono TunedControls and displays Remote control Tuner Display 6TUNE/ST +/- /ENTERDTV ON/OFF DTV InfoOperating range of remote control unit Listening in surround sound Listening to your systemListening to your system Chapter Auto playbackPRO LOGIC+THX Using the Home THX modesTHX Games Mode Listening to your systemPress EFFECT/CH SEL again to adjust other settings Using the Advanced surround effectsDolby Pro Logic IIx Music settings Use the +/- buttons to adjust the settingListening in stereo Neo6 Music settingsListening with Acoustic Calibration Listening to your system Choosing the input signal Type of source Extended Mode Standard / THX Type of source VirtualSB Mode Standard Enhancing dialog Using the tone controlsPress SHIFT+DIALOG E to switch dialog enhancement on or off Press Tone to select the frequency you want to adjust30 min Using the sleep timerListening to your system Playing other sources Selecting the multichannel analog inputsSurround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuSelect ‘MANUAL MCACC’ from the System Setup menu System Setup menuManual Mcacc speaker setup Select the surround back speaker settingFine Channel Distance Fine Channel LevelCopying your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ automaticallyAcoustic Calibration EQ Checking your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ manuallyFront Align Select the setting you want to check Manual speaker setupSelect ‘Manual SP Setup’ then press Enter Select ‘Speaker Setting’ from the Manual SP Setup menu Speaker SettingChannel Level Crossover NetworkSurround Back Speaker Position Select ‘Speaker Distance’ from the Manual SP Setup menuSelect ‘THX Audio Setting’ from the Manual SP Setup menu Speaker DistanceListening to the radio Using the tunerUsing the tuner Chapter Tuning directly to a stationAbcdefghijklmnopqrstuvwxyz Using the tuner Saving station presetsNaming station presets Listening to station presetsPrepare the recorder Making recordingsMaking recordings Chapter Making an audio or a video recordingControlling the rest of your system Chapter Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your systemPress the Receiver button to exit and store the operations Use cursor left/right to select Learn then press EnterConfirming preset codes Erasing all of the remote control presetsDirect function Disc Controlling the rest of your system Controls for TVsInput SelectSHIFT+ CD/MD/CD-R/DVD/LDShift + DVD Controlling the rest of your systemEnter Guide HDDOther connections Chapter Second Zone speaker B setupSwitching the speaker system Other connectionsOther connections Bi-amping your front speakers Bi-wiring your speakersFront left Speaker Using this receiver with a Pioneer plasma display Other connections Connecting additional amplifiersOther connections Using the SR+ mode with a Pioneer plasma displayDVD player Assigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuOther Setup menu Other SettingsAssigning the component video inputs Choose the setting that you want Dynamic Range Control SetupDual Mono Setup Select ‘DRC Setup’ from the Other Setup menuSelect ‘SR+ Setup’ from the Other Setup menu LFE Attenuator SetupSR+ Setup for Pioneer plasma displays Select ‘LFE ATT Setup’ from the Other Setup menuAdditional information Chapter TroubleshootingPower Additional informationNo sound Additional informationDigital inputs on Other audio problemsAudio components on VideoDisplay SettingsPress System Setup to confirm Resetting the main unitSwitching the speaker impedance Remote controlDolby Additional information Surround sound formatsWindows Media Audio 9 Professional About THXTHX MusicMode THX Select2 Cinema modeTHX Games Mode Advanced Speaker Array ASACleaning the unit Additional information SpecificationsPioneer Corporation

VSX-1015TX specifications

The Pioneer VSX-1015TX is a distinguished piece of audio equipment that caters to enthusiasts seeking an all-encompassing home theater experience. Launched in the mid-2000s, this receiver combines advanced technology with usability, making it a popular choice among music and movie aficionados.

One of the defining features of the VSX-1015TX is its robust multi-channel surround sound system. It supports up to 7.1 channels, allowing users to fully immerse themselves in their favorite films, games, and music. With a power output of 110 watts per channel, it delivers rich sound quality across various formats, enhancing the auditory experience.

The VSX-1015TX is equipped with Dolby Digital and DTS decoding, providing a comprehensive sound stage that captures every detail. Its Multi-Channel Acoustic Calibration System (MCACC) optimizes audio output based on the physical characteristics of your room. This feature intelligently analyzes the acoustics and adjusts the speakers to achieve balanced sound, ensuring that listeners receive the best audio experience possible.

Furthermore, the receiver supports many audio and video formats, including MPEG, WMA, and MP3, making it versatile for different media sources. The inclusion of HDMI inputs allows for high-definition video and audio transmission, simplifying connectivity with modern devices like Blu-ray players and gaming consoles.

Another notable characteristic of the VSX-1015TX is its user-friendly interface. The on-screen display and remote control make navigating through settings and configurations straightforward. Users can easily switch between different audio sources and adjust sound parameters to suit their preferences.

Additionally, this model is designed with several speaker configurations in mind, allowing for flexible setups. Whether you are using conventional speakers or opting for surround sound systems, the VSX-1015TX caters to various configurations, making it suitable for different home theater environments.

The Pioneer VSX-1015TX also emphasizes build quality and durability, ensuring that it can withstand the rigors of regular use while maintaining performance levels. With its blend of advanced features, streamlined usability, and robust sound performance, the VSX-1015TX remains a cherished option for those looking to enhance their audio-visual experiences at home.
Top Page Image Contents