Pioneer VSX-1015TX operating instructions Settings, Display

Page 70

12Additional information

Settings

Symptom

Cause

The Auto MCACC Setup

• The ambient noise level in the room is too

continually shows an error.

high, or obstacles are blocking the setup

 

microphone.

Remedy

•Keep the noise level in the room as low as possible when using the Auto MCACC Setup (see Other problems when using the Auto MCACC Setup on page 13 for more on this). If the noise cannot be kept low enough, you will have to set up the surround sound manually (page 45).

After using the Auto MCACC Setup, the speaker size setting (LARGE or SMALL) is incorrect.

•There was some inaudible low-frequency noise in the room.

•The low-frequency noise could have been caused by an air conditioner or motor. Switch off all appliances in the room and rerun the Auto MCACC Setup.

Display

Symptom

Cause

Remedy

The display is dark or off.

• The display is set to dark or off.

•Press FL. DIMMER on the remote control repeatedly to select a different brightness.

After making an adjustment the

• The display is set to off.

• Press FL. DIMMER on the remote control repeatedly to

display goes off.

 

select a different brightness.

 

 

 

You can't get DIGITAL to display

• There is a problem with the digital

• Check your digital connections and/or assign the digital

when using the SIGNAL SELECT

connections or the digital input is assigned

inputs correctly (see Assigning the digital inputs on

button.

incorrectly.

page 62).

 

 

 

 

• The multichannel analog inputs are

• Press MULTI CH IN again (see Selecting the

 

selected.

multichannel analog inputs on page 39).

 

 

 

The Dolby/DTS indicator doesn't

• The player is paused.

• Press play.

light when playing Dolby/DTS

 

 

• The player's sound output settings are

• Set the player correctly (consult the manual that came

software.

wrong.

with the player, if necessary).

 

 

 

 

When playing a DVD-Audio disc,

• The audio from these discs is output from

• This is not a malfunction. See also the operating

the DVD player display shows 96

the analog audio jacks of the DVD player only;

instructions that came with your DVD player.

kHz. However, the receiver’s

the receiver does not show the sampling rate

 

display does not.

of the input signal through the analog inputs.

 

 

 

 

During playback of a DTS 96/24

• The receiver’s input signal type is set to

• Set the receiver to AUTO or DIGITAL (see Choosing the

source, the display doesn't show

analog.

input signal on page 35).

96kHz.

 

 

 

 

 

When playing Dolby Digital or

• No digital connection, or the digital

• Check the digital audio connection (page 16).

DTS sources, the receiver’s

connection is incorrect.

 

format indicators do not light.

 

 

• The receiver’s input signal type is set to

• Set the receiver to AUTO or DIGITAL (see Choosing the

 

 

analog.

input signal on page 35).

 

 

 

 

• The DVD player is set to output Dolby Digital

• Check the settings on the player. Set the output for

 

and/or DTS audio as PCM.

Dolby Digital and DTS (no PCM conversion). See also the

 

 

operating instructions that came with your DVD player.

 

 

 

 

• The disc has several playback audio tracks;

• Switch the playback audio channel on your DVD player.

 

the one currently playing is actually PCM.

See the operating instructions that came with your DVD

 

 

player.

 

 

 

When playing certain discs,

• The audio format of the disc is not 5.1/6.1

• This is not a malfunction. Check the disc packaging for

none of the receiver’s format

channel.

details of the audio formats available on the disc.

indicators light.

 

 

 

 

 

When playing a disc, the

• The input signal type is set to analog.

• Set the receiver to AUTO or DIGITAL (see Choosing the

2 PL II or Neo:6 indicator lights

 

input signal on page 35).

on the receiver.

 

 

• A two channel soundtrack is currently

• This is not a malfunction. Check the disc packaging for

 

 

playing.

details of the audio formats available on the disc.

 

 

 

 

• The soundtrack currently playing is

• This is not a malfunction. Check the disc packaging for

 

encoded using Dolby Surround.

details of the audio formats available on the disc.

 

 

 

During playback of a Surround

•The source may be Dolby Surround EX / DTS

• Set to Extended ON (see Using the surround back

EX or DTS ES source on the

ES software, but it has no flag to indicate it is

channel (Extended mode) on page 36) then switch to the

Extended AUTO setting, the EX

6.1 compatible.

THX Surround EX or Standard EX listening mode (see

and ES indicators don’t light, or

 

Listening in surround sound on page 31).

the signal is not properly

 

 

processed.

 

 

 

 

 

70

En

Page 69 Page 71
Image 70
Page 69 Page 71
Contents VSX-1015TX Wash hands after handling Information to UserImportant Safety Instructions Contents Other connections Other SettingsControlling the rest of your system Additional informationBefore you start Chapter FeaturesBefore you start Checking what’s in the boxBefore you start Ventilation Installing the receiverLoading the batteries Introduction to home theater Minute guide02 5 minute guide Chapter Listening to Surround SoundMinute guide Connect your speakers02 5 minute guide Make sure ‘Normal SB’ is selected then press EnterFollow the instructions on-screen Other problems when using the Auto Mcacc Setup Checking the settings on your DVD or other playerPlaying a source Connecting up Chapter Connecting upAbout cable types Connecting up About the video converterConnecting up Connecting digital audio components CD recorder DVD or LD player CD playerConnecting multichannel analog components Connecting up Connecting analog audio componentsTip Connecting to the front panel video terminal Connecting up Connecting video componentsVideo Camera FM wire antenna Connecting up Connecting antennasUsing external antennas AM loop antennaSpeaker terminals Connecting up Connecting the speakersTighten terminal Overhead view of speaker setup Hints on speaker placementView of 7.1 channel speaker setup Connecting upTHX speaker system setup AC outletPower cord caution Operating other Pioneer componentsControls and displays Chapter Listening Mode SelectControls and displays Front panelControls and displays Controls and displays Display Tuned StereoMono SleepControls and displays Remote control DTV Info 6TUNE/ST +/- /ENTERDTV ON/OFF Tuner DisplayOperating range of remote control unit Auto playback Listening to your systemListening to your system Chapter Listening in surround soundListening to your system Using the Home THX modesTHX Games Mode PRO LOGIC+THXUse the +/- buttons to adjust the setting Using the Advanced surround effectsDolby Pro Logic IIx Music settings Press EFFECT/CH SEL again to adjust other settingsListening in stereo Neo6 Music settingsListening with Acoustic Calibration Listening to your system Choosing the input signal Type of source Extended Mode Standard / THX Type of source VirtualSB Mode Standard Press Tone to select the frequency you want to adjust Using the tone controlsPress SHIFT+DIALOG E to switch dialog enhancement on or off Enhancing dialogSelecting the multichannel analog inputs Using the sleep timerListening to your system Playing other sources 30 minMaking receiver settings from the System Setup menu System Setup menuSystem Setup menu Chapter Surround back speaker settingSelect the surround back speaker setting System Setup menuManual Mcacc speaker setup Select ‘MANUAL MCACC’ from the System Setup menuFine Channel Level Fine Channel DistanceCopying your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ automaticallyAcoustic Calibration EQ Checking your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ manuallyFront Align Select the setting you want to check Manual speaker setupSelect ‘Manual SP Setup’ then press Enter Speaker Setting Select ‘Speaker Setting’ from the Manual SP Setup menuCrossover Network Channel LevelSpeaker Distance Select ‘Speaker Distance’ from the Manual SP Setup menuSelect ‘THX Audio Setting’ from the Manual SP Setup menu Surround Back Speaker PositionTuning directly to a station Using the tunerUsing the tuner Chapter Listening to the radioListening to station presets Using the tuner Saving station presetsNaming station presets AbcdefghijklmnopqrstuvwxyzMaking an audio or a video recording Making recordingsMaking recordings Chapter Prepare the recorderControlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your system ChapterUse cursor left/right to select Learn then press Enter Press the Receiver button to exit and store the operationsConfirming preset codes Erasing all of the remote control presetsDirect function Select Controlling the rest of your system Controls for TVsInput DiscCD/MD/CD-R/DVD/LD SHIFT+HDD Controlling the rest of your systemEnter Guide Shift + DVDOther connections Second Zone speaker B setupSwitching the speaker system Other connections ChapterOther connections Bi-amping your front speakers Bi-wiring your speakersFront left Speaker Other connections Connecting additional amplifiers Using this receiver with a Pioneer plasma displayOther connections Using the SR+ mode with a Pioneer plasma displayDVD player Input Assign menu Other SettingsOther Settings Chapter Assigning the digital inputsOther Setup menu Other SettingsAssigning the component video inputs Select ‘DRC Setup’ from the Other Setup menu Dynamic Range Control SetupDual Mono Setup Choose the setting that you wantSelect ‘LFE ATT Setup’ from the Other Setup menu LFE Attenuator SetupSR+ Setup for Pioneer plasma displays Select ‘SR+ Setup’ from the Other Setup menuAdditional information TroubleshootingPower Additional information ChapterAdditional information No soundOther audio problems Digital inputs onVideo Audio components onSettings DisplayRemote control Resetting the main unitSwitching the speaker impedance Press System Setup to confirmAdditional information Surround sound formats DolbyAbout THX Windows Media Audio 9 ProfessionalAdvanced Speaker Array ASA THX Select2 Cinema modeTHX Games Mode THX MusicModeAdditional information Specifications Cleaning the unitPioneer Corporation

VSX-1015TX specifications

The Pioneer VSX-1015TX is a distinguished piece of audio equipment that caters to enthusiasts seeking an all-encompassing home theater experience. Launched in the mid-2000s, this receiver combines advanced technology with usability, making it a popular choice among music and movie aficionados.

One of the defining features of the VSX-1015TX is its robust multi-channel surround sound system. It supports up to 7.1 channels, allowing users to fully immerse themselves in their favorite films, games, and music. With a power output of 110 watts per channel, it delivers rich sound quality across various formats, enhancing the auditory experience.

The VSX-1015TX is equipped with Dolby Digital and DTS decoding, providing a comprehensive sound stage that captures every detail. Its Multi-Channel Acoustic Calibration System (MCACC) optimizes audio output based on the physical characteristics of your room. This feature intelligently analyzes the acoustics and adjusts the speakers to achieve balanced sound, ensuring that listeners receive the best audio experience possible.

Furthermore, the receiver supports many audio and video formats, including MPEG, WMA, and MP3, making it versatile for different media sources. The inclusion of HDMI inputs allows for high-definition video and audio transmission, simplifying connectivity with modern devices like Blu-ray players and gaming consoles.

Another notable characteristic of the VSX-1015TX is its user-friendly interface. The on-screen display and remote control make navigating through settings and configurations straightforward. Users can easily switch between different audio sources and adjust sound parameters to suit their preferences.

Additionally, this model is designed with several speaker configurations in mind, allowing for flexible setups. Whether you are using conventional speakers or opting for surround sound systems, the VSX-1015TX caters to various configurations, making it suitable for different home theater environments.

The Pioneer VSX-1015TX also emphasizes build quality and durability, ensuring that it can withstand the rigors of regular use while maintaining performance levels. With its blend of advanced features, streamlined usability, and robust sound performance, the VSX-1015TX remains a cherished option for those looking to enhance their audio-visual experiences at home.
Top Page Image Contents