Pioneer VSX-1015TX Resetting the main unit, Switching the speaker impedance, Remote control

Page 71

Additional information

12

Remote control

Symptom

Cause

Remedy

Cannot be remote controlled.

• The remote control batteries have worn out. • Replace the batteries (see Loading the batteries on

 

 

page 7).

 

 

 

• Too far away or improper angle of operation. • Operate within 23 feet and a 30º angle of the remote

 

 

sensor on the front panel (see Operating range of remote

 

 

control unit on page 30).

 

 

 

 

• There is an obstacle between the receiver

• Remove the obstacle or move to another place.

 

and the remote control.

 

 

 

 

 

• Strong light such as fluorescent light is

• Avoid exposing the remote sensor on the front panel to

 

shining onto the unit's remote control sensor.

direct light.

 

 

 

 

• Something is plugged into the CONTROL IN

• Unplug the cable from the CONTROL IN jack and use

 

jack.

remote normally (see Operating other Pioneer components

 

 

on page 23).

 

 

 

Other components can't be

• The preset code settings are wrong.

• Input the correct preset code.

operated with the system

• The batteries wore out and the system

• Reset the proper system settings.

remote.

settings were cleared.

 

The SR cable is connected, but the connected components can’t be operated with the remote.

• The SR cable hasn't been connected

• Reinsert the SR cable, making sure it’s connected to the

properly.

right jack (see Operating other Pioneer components on

 

page 23).

 

 

• The rest of the component connections

• Make sure an analog connection has been made

have not been made.

between the units.

•The component you have hooked up is not a • This feature only works with Pioneer products. Pioneer product.

Note

•If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.

Resetting the main unit

Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.

1Switch the receiver into standby.

2While holding down the TONE button, press and

hold the STANDBY/ON button for about three seconds.

3When you see RESET? appear in the display, press ENTER.

OK? shows in the display.

4Press SYSTEM SETUP to confirm.

OK appears in the display to indicate that the receiver has been reset to the factory default settings.

Switching the speaker impedance

We recommend using speakers of 8Ω with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6Ω impedance rating.

• With the receiver in standby, press STANDBY/ ON while holding down the SPEAKERS button. Each time you do this, you switch between the impedance settings:

•SP 6 OHM – Use this setting if your speakers are rated at 6Ω.

•SP 8 OHM – Use this setting if your speakers are rated at 8Ω or more.

71

En

Page 70 Page 72
Image 71
Page 70 Page 72
Contents VSX-1015TX Information to User Wash hands after handlingImportant Safety Instructions Contents Additional information Other SettingsControlling the rest of your system Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterLoading the batteries Installing the receiverBefore you start Ventilation Listening to Surround Sound Minute guide02 5 minute guide Chapter Introduction to home theaterConnect your speakers Minute guide02 5 minute guide Enter Make sure ‘Normal SB’ is selected then pressFollow the instructions on-screen Playing a source Checking the settings on your DVD or other playerOther problems when using the Auto Mcacc Setup About cable types Connecting upConnecting up Chapter About the video converter Connecting upCD recorder DVD or LD player CD player Connecting up Connecting digital audio componentsTip Connecting up Connecting analog audio componentsConnecting multichannel analog components Video Camera Connecting up Connecting video componentsConnecting to the front panel video terminal AM loop antenna Connecting up Connecting antennasUsing external antennas FM wire antennaTighten terminal Connecting up Connecting the speakersSpeaker terminals Hints on speaker placement Overhead view of speaker setupAC outlet Connecting upTHX speaker system setup View of 7.1 channel speaker setupOperating other Pioneer components Power cord cautionFront panel Listening Mode SelectControls and displays Controls and displays ChapterControls and displays Controls and displays Display Sleep StereoMono TunedControls and displays Remote control Tuner Display 6TUNE/ST +/- /ENTERDTV ON/OFF DTV InfoOperating range of remote control unit Listening in surround sound Listening to your systemListening to your system Chapter Auto playbackPRO LOGIC+THX Using the Home THX modesTHX Games Mode Listening to your systemPress EFFECT/CH SEL again to adjust other settings Using the Advanced surround effectsDolby Pro Logic IIx Music settings Use the +/- buttons to adjust the settingListening with Acoustic Calibration Neo6 Music settingsListening in stereo Listening to your system Choosing the input signal Type of source Extended Mode Standard / THX Type of source VirtualSB Mode Standard Enhancing dialog Using the tone controlsPress SHIFT+DIALOG E to switch dialog enhancement on or off Press Tone to select the frequency you want to adjust30 min Using the sleep timerListening to your system Playing other sources Selecting the multichannel analog inputsSurround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuSelect ‘MANUAL MCACC’ from the System Setup menu System Setup menuManual Mcacc speaker setup Select the surround back speaker settingFine Channel Distance Fine Channel LevelAcoustic Calibration EQ Setting the Acoustic Calibration EQ automaticallyCopying your Acoustic Calibration EQ settings Front Align Setting the Acoustic Calibration EQ manuallyChecking your Acoustic Calibration EQ settings Select ‘Manual SP Setup’ then press Enter Manual speaker setupSelect the setting you want to check Select ‘Speaker Setting’ from the Manual SP Setup menu Speaker SettingChannel Level Crossover NetworkSurround Back Speaker Position Select ‘Speaker Distance’ from the Manual SP Setup menuSelect ‘THX Audio Setting’ from the Manual SP Setup menu Speaker DistanceListening to the radio Using the tunerUsing the tuner Chapter Tuning directly to a stationAbcdefghijklmnopqrstuvwxyz Using the tuner Saving station presetsNaming station presets Listening to station presetsPrepare the recorder Making recordingsMaking recordings Chapter Making an audio or a video recordingControlling the rest of your system Chapter Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your systemPress the Receiver button to exit and store the operations Use cursor left/right to select Learn then press EnterDirect function Erasing all of the remote control presetsConfirming preset codes Disc Controlling the rest of your system Controls for TVsInput SelectSHIFT+ CD/MD/CD-R/DVD/LDShift + DVD Controlling the rest of your systemEnter Guide HDDOther connections Chapter Second Zone speaker B setupSwitching the speaker system Other connectionsFront left Speaker Bi-wiring your speakersOther connections Bi-amping your front speakers Using this receiver with a Pioneer plasma display Other connections Connecting additional amplifiersDVD player Using the SR+ mode with a Pioneer plasma displayOther connections Assigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuAssigning the component video inputs Other SettingsOther Setup menu Choose the setting that you want Dynamic Range Control SetupDual Mono Setup Select ‘DRC Setup’ from the Other Setup menuSelect ‘SR+ Setup’ from the Other Setup menu LFE Attenuator SetupSR+ Setup for Pioneer plasma displays Select ‘LFE ATT Setup’ from the Other Setup menuAdditional information Chapter TroubleshootingPower Additional informationNo sound Additional informationDigital inputs on Other audio problemsAudio components on VideoDisplay SettingsPress System Setup to confirm Resetting the main unitSwitching the speaker impedance Remote controlDolby Additional information Surround sound formatsWindows Media Audio 9 Professional About THXTHX MusicMode THX Select2 Cinema modeTHX Games Mode Advanced Speaker Array ASACleaning the unit Additional information SpecificationsPioneer Corporation

VSX-1015TX specifications

The Pioneer VSX-1015TX is a distinguished piece of audio equipment that caters to enthusiasts seeking an all-encompassing home theater experience. Launched in the mid-2000s, this receiver combines advanced technology with usability, making it a popular choice among music and movie aficionados.

One of the defining features of the VSX-1015TX is its robust multi-channel surround sound system. It supports up to 7.1 channels, allowing users to fully immerse themselves in their favorite films, games, and music. With a power output of 110 watts per channel, it delivers rich sound quality across various formats, enhancing the auditory experience.

The VSX-1015TX is equipped with Dolby Digital and DTS decoding, providing a comprehensive sound stage that captures every detail. Its Multi-Channel Acoustic Calibration System (MCACC) optimizes audio output based on the physical characteristics of your room. This feature intelligently analyzes the acoustics and adjusts the speakers to achieve balanced sound, ensuring that listeners receive the best audio experience possible.

Furthermore, the receiver supports many audio and video formats, including MPEG, WMA, and MP3, making it versatile for different media sources. The inclusion of HDMI inputs allows for high-definition video and audio transmission, simplifying connectivity with modern devices like Blu-ray players and gaming consoles.

Another notable characteristic of the VSX-1015TX is its user-friendly interface. The on-screen display and remote control make navigating through settings and configurations straightforward. Users can easily switch between different audio sources and adjust sound parameters to suit their preferences.

Additionally, this model is designed with several speaker configurations in mind, allowing for flexible setups. Whether you are using conventional speakers or opting for surround sound systems, the VSX-1015TX caters to various configurations, making it suitable for different home theater environments.

The Pioneer VSX-1015TX also emphasizes build quality and durability, ensuring that it can withstand the rigors of regular use while maintaining performance levels. With its blend of advanced features, streamlined usability, and robust sound performance, the VSX-1015TX remains a cherished option for those looking to enhance their audio-visual experiences at home.
Top Page Image Contents