Pioneer VSX-D908S operating instructions SymptomCause

Page 81
Remedy
• See “speaker setting” on p.26 to check the speaker settings.
• See “channel level” p.29 to check the speaker levels.
• Connect the speakers (see p.14).
• Set SIGNAL SELECT to “DIGITAL” or “ANALOG” according to the type of connections made (see p. 40).
• Set the digital input settings correctly (see p.10, 34).
• Make digital connections (see p.10) and set SIGNAL SELECT to “DIGITAL” (see p.40).
• Refer to the instruction manual supplied with the DVD player.
• Set the digital volume level of the player to full, or to the neutral position.
• Use the STANDAD mode to get the best results (see memo, p.38).
• This is not a malfunction, but be sure to turn the volume down to prevent the output of loud noise from your speakers.
Techno Tidbits & Problem-solving

SymptomCause

No sound from surround or center speakers.

•Speaker settings are incorrect.

•The rear and/or center levels are turned down.

•The surround and/or center speakers are disconnected.

Sound is produced from some components, but not from digital components.

•SIGNAL SELECT is set incorrectly.

•The digital inputs are assigned incorrectly, or not at all.

No sound is output or a noise is output when software with DTS is played back.

•SIGNAL SELECT is set to “ANALOG”.

•A DVD player not compatible with DTS is used, or the setting of the DVD player is incorrect.

•The digital output level has been turned down on a CD player or other component equipped with digital output level adjustment capability. (The DTS signal has been altered by the player, and cannot be read.)

The sound is output intermittently when software with DTS is played back. The overload indicator is lit.

•Disc being played back has a huge amount of information on it.

When a search is performed by a DTS compatible CD player during playback, noise is output.

•The search function performed by the player interferes with the reading of digital information.

Cannot be remote controlled.

• The remote control batteries have

• Replace the batteries (see p.7).

 

worn out.

 

 

• Too far away or bad angle of

• Operate within 7 m (23 feet), 30°

 

operation.

of the remote sensor on the front

 

 

panel (see p.7).

 

• There is an obstacle between the

• Remove the obstacle or operate

 

receiver and the remote control.

from another position.

 

• Strong light such as fluorescent

• Avoid exposing the remote sensor

 

light is shining onto the unit’s

on the front panel to direct light.

 

remote control signal light-receiving

 

window.

 

 

• A cord is connected to the

• Connect cord to the correct jack.

 

CONTROL IN terminal on this unit.

 

 

• The IR -Receiver type is

• Disconnect the IR Receiver from

 

mismatched with the setting.

the rear panel, and set to the other

 

 

IR Receiver type (see p.73).

The display is dark.

• The FL DIMMER button is pushed. • Press FL DIMMER on the front

 

 

panel repeatedly to return to the

 

 

default setting (see p.45).

If the unit does not operate normally due to external effects such as static electricity

Disconnect the power plug from the outlet and insert again to return to normal operating conditions.

81

Page 80 Page 82
Image 81
Page 80 Page 82
Contents VSX-D908S This is for your security For Canadian modelInformation to User Important Safety InstructionsFeatures Table of Contents How to Use This Manual Checking the Supplied AccessoriesInstalling the Receiver Before You StartOperating range of remote control unit Preparing the Remote ControlOpening the Front Panel Loading the batteriesCassette deck placement Connecting Your EquipmentAudio Components Audio cordsVideo Components FrontAudio/Video cords Digital Connections Digital audio cords/Optical cablesDigital audio cord Optical cable Or standard video cord Example of Connection Using a DVD/LD or LD player When playing LD recorded in Dolby DigitalDVD/LD player Or LD player RF demodulator RFD-1 Components equipped with 5.1 channel analog output jacks External Decoder InputAntennas Using external antennasAM loop antenna To improve FM receptionTo be used as Center Speaker Powered sub woofer SpeakersFront Speakers a Speaker impedance First turn the receiver off, then press the power buttonSpeaker terminals While holding down the Speakers buttonFront Center Speaker placementRight Sub WooferPower connections AC Outlets Connecting additional amplifiersSwitched Total 100 W 0.8 a MAX Unswitched 100 W 0.8 a MAXDisplay Displays & Controls~ Tuner indicators = LFE indicator@ Speaker indicators # H.P headphonesFront Panel = Master Volume Remote Control Remote Setup button System SET UP button# Master Volume button Signal Select buttonSetting Up for Surround Sound Surround Sound Set UpPress System Setup button On Screen DisplayGo on to the next page to continue set up Speaker Setting Select Speaker Setting with the 5´ buttonsPress Enter Center default setting is Large Front default setting is LargeSurround default setting is Large SUB Woofer default setting is YESUsing the commands below Channel DelayUse the 5´ buttons to select a speaker. Specify Distance from your listening position to each speakerChannel Level Select aTEST Tone modeAuto automatic Test Tone Manual manual Test ToneManu mode Auto modeIf you are using a Sound Pressure Level SPL meter To exit before outputting the Test ToneSelect Exit to return to the System Setup Menu Crossover NetworkSpecify the crossover frequency for your small speakers Select Setting Start and press Enter Bass Peak Level ManagerPress Enter to return to the previous screen Use the 2 or 3 arrows to choose OFF, MID or MAX Range ControlChoose a Digital in and assign it an input function Digital-In SelectPlaying Sources with Stereo Sound Basic PlaybackSound modes Standard modeDSP modes Stereo modeHall JazzSelecting a Sound Mode Select the sound modeSurrround operation For more see Sound Modes p Playing Sources with Dolby Digital or DTS SoundAnalog Digital Switching ANALOG/DIGITAL Signal InputReducing noise during playback Digital NR function Each press switches Midnight Listening mode on or off Listening in Midnight Listening ModePress Midnight Midnight96kHz24bit Performance External decoder playback front panel onlyPress External Decorder External DecorderListening in Loudness Mode front panel only Adjusting bass and treble tone control front panel onlyDirect playback front panel only Adjusting the brightness of the display front panel only Press FL DimmerFL Dimmer Automatic and Manual Tuning Using the TunerMPX Mode Adjust the volumeTo cancel before inputting the frequency Direct Access TuningPress Tuner Press Band button on the remote or the FM/AMMemorizing Frequently Used Stations Using the front panelTune in the desired station Press Memory to activate the memory functionRecalling Memorized Stations Using the remote controlSetting Up the Remote Control to Control Other Components Remote Control of Other componentRecalling preset codes Press Remote SetupPress the Multi Control button for the component Press Remote Setup to exit the Preset Recall Setup modeYou want to control Press the 5´ buttons repeatedly to display the nameRemote Setup menu appears on your TV screen To cancel Learning Setup modeSelected button continues to blink Press the button to be programmed Press Remote Setup to exit the Learning Setup modeInches To program additional operations for the current componentDVD or LD player operations Remote Controlling Other ComponentsSouce Enter Side A/BSource VCR & DVD video recorder operationsChannel -/+ Use to select channelsDisc CD player operationsDisc DISP/CHARA MD operationsGuide STB satellite tuner operationsExit MenuSTB DTV operations TV operations Press to switch the TV on or offDTV Menu DTV ON/OFFCassette deck operations Press to switch the cassette deck on or off notNumber buttons 1~6 Possible with all modelsUsing Other Functions Recording from Audio ComponentsRecord monitor Tape 2 Monitor Recording from Digital Audio Components Recording from Video Components To cancel MULTI-OPERATION Setup mode Press Remote SetupMulti Operations Press the Multi Operation button on the remote control 47Press Remote Setup to exit the MULTI-OPERATION Setup modePerforming multi operations Multi Control buttons start to blinkSystem OFF You can repeat this process for up to five commandsUsing the system off button Setting up the direct functionPress and hold both Remote Setup Remote Back LightOFF MID MAX Erasing the multi operations Resetting the Remote ControlErasing all signals learned & preset codes Erasing the learned remote control commandsSet up example Multi-RoomMULTI-ROOM connections Press System Setup on the remote control MULTI-ROOM set upUp mode and press Enter Select the Volume Level by using the 2´3 buttonsPress the Multi Room & Source button Using the front panel with the MULTI-ROOM systemPress the Control button DVD/LD TV/SAT CD VCR 1 Tuner MD/TAPEPress Volume +/- to adjust the volume Using the remote control with the MULTI-ROOM systemClass Receiver Station +Control Dolby Digital Techno Tidbits & Problem-solvingLaser disc format Comparison with Dolby Pro Logic SurroundDTS Dolby DigitalDolby Pro Logic SurroundPreset Code List Device Manufacturer CodeDevice Symptom Cause Remedy TroubleshootingFM broadcasts AM broadcastsSymptomCause Specifications 0 4 2 1 1 4 0 99E00ZF0P00 EIA

VSX-D908S specifications

The Pioneer VSX-D908S is a remarkable home theater receiver that epitomizes the blend of advanced technology and user-friendly design. Launched in the early 2000s, this versatile component remains a popular choice for audio enthusiasts seeking to enhance their home entertainment experience.

One of the standout features of the VSX-D908S is its powerful amplification system, capable of delivering up to 100 watts per channel across five channels. This ensures that users can enjoy dynamic sound reproduction, even with demanding audio tracks or during intense movie scenes. The receiver supports both Dolby Digital and DTS surround formats, making it an ideal choice for those looking to immerse themselves in a cinematic experience at home.

The VSX-D908S also boasts multiple inputs and outputs, allowing users to connect a variety of audio and video sources. With several composite, S-video, and component video inputs, it accommodates a range of devices, from DVD players to gaming consoles. Furthermore, the receiver features a built-in AM/FM tuner and supports the playback of music CDs, making it a comprehensive solution for all entertainment needs.

Another notable characteristic is the advanced DSP (Digital Signal Processing) technology that the VSX-D908S incorporates. This technology allows for the simulation of different acoustic environments, enabling the user to customize their listening experience according to their preferences. With multiple preset sound fields, including options for concert halls and theaters, the receiver adapts to various audio situations seamlessly.

For those who value ease of use, the VSX-D908S includes a user-friendly interface and remote control. The intuitive layout of the front panel makes it simple to navigate settings, adjust volumes, and switch between sources. The inclusion of a multi-language on-screen display further enhances the user experience, catering to a broader audience.

In addition to its impressive audio capabilities, the Pioneer VSX-D908S also emphasizes build quality, featuring solid construction and reliability. With its robust design, users can expect long-term performance without compromising on sound quality.

Overall, the Pioneer VSX-D908S stands out as a home theater receiver that harmonizes performance, versatility, and user-friendliness. It continues to be a solid option for anyone seeking to elevate their audio-visual setup, making it a notable piece of equipment in the world of home entertainment.
Top Page Image Contents