Pioneer VSX-D908S operating instructions Specifications

Page 82

Techno Tidbits & Problem-solving

Specifications

Amplifier Section

Continuous average power output of 100 watts* per channel, min., at 8 ohms, from 20 Hz to 20,000 Hz with no more than 0.09 %** total harmonic distortion (front).

Continuous Power Output

Front

100 W + 100 W (20 Hz-20 kHz, 0.09 %, 8 Ω)

Center

100 W (20 Hz-20 kHz, 0.09 %, 8 Ω)

Rear

100 W + 100 W (20 Hz-20 kHz, 0.09 %, 8 Ω)

Input (Sensitivity/Impedance)

PHONO MM

4.7 mV/47 kΩ

VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO, CD, MD/TAPE

1, TAPE 2

...............................................

335 mV/47 kΩ

Frequency Response

 

PHONO MM

20 Hz to 20,000 Hz ± 0.3 dB

VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO, CD, MD/TAPE

1, TAPE 2

 

+0

..............................

5 Hz to 100,000 Hz –3dB

Output (Level/Impedance)

VCR 1 REC, VCR 2 REC, MD/TAPE 1 REC, TAPE 2 REC

.........................................................

335 mV/2.2 kΩ

Tone Control

 

BASS

± 6 dB (100 Hz)

TREBLE

± 6 dB (10 kHz)

LOUDNESS

+3 dB (100 Hz/10 kHz)

Signal-to-Noise Ratio (IHF, short circuited, A network)

PHONO MM

80 dB

VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO, CD, MD/TAPE,

TAPE 2

97 dB

Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]

PHONO MM

80 dB

VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO, CD, MD/TAPE,

TAPE 2

83 dB

*Measured pursuant to the Federal Trade Commission’s Trade Regulation rule on Power Output Claims for Amplifiers.

**Measured by Audio Spectrum Analyzer.

VIDEO Section

Input (Sensitivity/Impedance)

 

1 Vp-p/75 Ω

VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO

Output (Level/Impedance)

 

1 Vp-p/75 Ω

VCR 1, VCR 2, MONITOR

Frequency Response

 

 

VCR 1, VCR 2, MONITOR

 

+0

5 Hz to 10 MHz –3dB

Signal-to-Noise Ratio

55 dB

FM Tuner Section

 

 

Frequency Range

87.5 MHz to 108 MHz

Usable Sensitivity

Mono: 13.2 dBf, IHF (1.3 µV/75 Ω)

50 dB Quieting Sensitivity

Mono: 20.2 dBf

 

 

 

Stereo: 38.6 dBf

Signal-to-Noise Ratio

Mono: 73 dB (at 85 dBf)

 

 

Stereo: 70 dB (at 85 dBf)

Distortion

Stereo: 0.5 % (1 kHz)

Alternate Channel Selectivity

60 dB (400 kHz)

Stereo Separation

 

40 dB (1 kHz)

Frequency Response

30 Hz to 15 kHz (± 1) dB

Antenna Input

75 Ω unbalanced

AM Tuner Section

 

 

Frequency Range

530 kHz to 1,700 kHz

Sensitivity (IHF, Loop antenna)

350 µV/m

Selectivity

 

25 dB

Signal-to-Noise Ratio

 

50 dB

Antenna

 

Loop antenna

Miscellaneous

 

 

 

Power Requirements

 

AC 120 V, 60 Hz

Power Consumption

 

400 W, 550 VA

Power Consumption in Standby mode

1.0 W

AC Outlet

 

 

 

SWITCHED (×2)

Total 100 W (0.8 A) MAX

UNSWITCHED

100 W (0.8 A) MAX

Dimensions

420 (W) × 173 (H) × 470 (D) mm

................ 16-9/16 (W) × 6-13/16 (H) × 18-1/2 (D) in.

Weight (without package)

14.1 kg (31 lb 1 oz)

Furnished Parts

 

 

 

FM Antenna

 

1

AM Loop Antenna

 

1

Dry Cell Batteries (SIZE “AA” (IEC LR6))

....................... 2

Remote Control Unit

 

1

Operating Instructions

...................................................

1

NOTE:

Specifications and the design are subject to possible modifications without notice, due to improvements.

82

Page 81 Page 83
Image 82
Page 81 Page 83
Contents VSX-D908S For Canadian model This is for your securityImportant Safety Instructions Information to UserFeatures Table of Contents Installing the Receiver Checking the Supplied AccessoriesHow to Use This Manual Before You StartOpening the Front Panel Preparing the Remote ControlOperating range of remote control unit Loading the batteriesAudio Components Connecting Your EquipmentCassette deck placement Audio cordsFront Video ComponentsAudio/Video cords Digital audio cords/Optical cables Digital ConnectionsDigital audio cord Optical cable Or standard video cord When playing LD recorded in Dolby Digital Example of Connection Using a DVD/LD or LD playerDVD/LD player Or LD player RF demodulator RFD-1 External Decoder Input Components equipped with 5.1 channel analog output jacksAM loop antenna Using external antennasAntennas To improve FM receptionSpeakers To be used as Center Speaker Powered sub wooferFront Speakers a Speaker terminals First turn the receiver off, then press the power buttonSpeaker impedance While holding down the Speakers buttonRight Speaker placementFront Center Sub WooferSwitched Total 100 W 0.8 a MAX Connecting additional amplifiersPower connections AC Outlets Unswitched 100 W 0.8 a MAXDisplays & Controls Display@ Speaker indicators = LFE indicator~ Tuner indicators # H.P headphonesFront Panel = Master Volume Remote Control # Master Volume button System SET UP buttonRemote Setup button Signal Select buttonPress System Setup button Surround Sound Set UpSetting Up for Surround Sound On Screen DisplayGo on to the next page to continue set up Select Speaker Setting with the 5´ buttons Speaker SettingPress Enter Surround default setting is Large Front default setting is LargeCenter default setting is Large SUB Woofer default setting is YESUse the 5´ buttons to select a speaker. Specify Channel DelayUsing the commands below Distance from your listening position to each speakerAuto automatic Test Tone Select aTEST Tone modeChannel Level Manual manual Test ToneIf you are using a Sound Pressure Level SPL meter Auto modeManu mode To exit before outputting the Test ToneCrossover Network Select Exit to return to the System Setup MenuSpecify the crossover frequency for your small speakers Bass Peak Level Manager Select Setting Start and press EnterPress Enter to return to the previous screen Range Control Use the 2 or 3 arrows to choose OFF, MID or MAXDigital-In Select Choose a Digital in and assign it an input functionBasic Playback Playing Sources with Stereo SoundStandard mode Sound modesHall Stereo modeDSP modes JazzSelect the sound mode Selecting a Sound ModeSurrround operation Playing Sources with Dolby Digital or DTS Sound For more see Sound Modes pSwitching ANALOG/DIGITAL Signal Input Analog DigitalReducing noise during playback Digital NR function Press Midnight Listening in Midnight Listening ModeEach press switches Midnight Listening mode on or off MidnightPress External Decorder External decoder playback front panel only96kHz24bit Performance External DecorderAdjusting bass and treble tone control front panel only Listening in Loudness Mode front panel onlyDirect playback front panel only Press FL Dimmer Adjusting the brightness of the display front panel onlyFL Dimmer MPX Mode Using the TunerAutomatic and Manual Tuning Adjust the volumePress Tuner Direct Access TuningTo cancel before inputting the frequency Press Band button on the remote or the FM/AMTune in the desired station Using the front panelMemorizing Frequently Used Stations Press Memory to activate the memory functionUsing the remote control Recalling Memorized StationsRecalling preset codes Remote Control of Other componentSetting Up the Remote Control to Control Other Components Press Remote SetupYou want to control Press Remote Setup to exit the Preset Recall Setup modePress the Multi Control button for the component Press the 5´ buttons repeatedly to display the nameTo cancel Learning Setup mode Remote Setup menu appears on your TV screenSelected button continues to blink Inches Press Remote Setup to exit the Learning Setup modePress the button to be programmed To program additional operations for the current componentSouce Remote Controlling Other ComponentsDVD or LD player operations Enter Side A/BChannel -/+ VCR & DVD video recorder operationsSource Use to select channelsCD player operations DiscMD operations Disc DISP/CHARAExit STB satellite tuner operationsGuide MenuSTB DTV operations DTV Menu Press to switch the TV on or offTV operations DTV ON/OFFNumber buttons 1~6 Press to switch the cassette deck on or off notCassette deck operations Possible with all modelsRecording from Audio Components Using Other FunctionsRecord monitor Tape 2 Monitor Recording from Digital Audio Components Recording from Video Components Press Remote Setup To cancel MULTI-OPERATION Setup modeMulti Operations Performing multi operations 47Press Remote Setup to exit the MULTI-OPERATION Setup modePress the Multi Operation button on the remote control Multi Control buttons start to blinkYou can repeat this process for up to five commands System OFFSetting up the direct function Using the system off buttonRemote Back Light Press and hold both Remote SetupOFF MID MAX Resetting the Remote Control Erasing the multi operationsErasing the learned remote control commands Erasing all signals learned & preset codesMulti-Room Set up exampleMULTI-ROOM connections Up mode and press Enter MULTI-ROOM set upPress System Setup on the remote control Select the Volume Level by using the 2´3 buttonsPress the Control button Using the front panel with the MULTI-ROOM systemPress the Multi Room & Source button DVD/LD TV/SAT CD VCR 1 Tuner MD/TAPEClass Using the remote control with the MULTI-ROOM systemPress Volume +/- to adjust the volume Receiver Station +Control Laser disc format Techno Tidbits & Problem-solvingDolby Digital Comparison with Dolby Pro Logic SurroundDolby Pro Logic Dolby DigitalDTS Surround Device Manufacturer Code Preset Code List Device FM broadcasts TroubleshootingSymptom Cause Remedy AM broadcastsSymptomCause Specifications 0 4 2 1 1 4 0 EIA 99E00ZF0P00
Top Page Image Contents