Pioneer S-3EX Installation and Placement, How to install, Mounting the Fall-Prevention Fastener

Page 6

Installation and Placement

How to install

This speaker system is supported by three points (the front two legs, and the back spike located between the back two legs).

Front

Nut (for spike)

Cabinet base

Back

Back spike

 

Legs

1Choose the location for speaker placement then put the spike bases on the floor.

2Place the speaker on top of the spike bases.

3If either the left or right back legs touches the ground before the back spike, resulting in the speaker not resting flat on its placed surface, adjust the back spike so it extends to the ground before either of the back legs.

4Place the included mounting pads underneath the back legs to keep the speaker stable.

Choose the most appropriate thickness of mounting pad from the several types included.

Mounting the Fall-Prevention Fastener

Using the included screw, tightly secure the metal catch to the backside of the speaker.

Pass a commercially-available reinforced string through the metal catch to securely support the speaker to the wall. Be sure that the wall to which you fasten the speaker is strong enough to support the weight of the speaker. After fastening the speaker, make sure that it does not fall over.

The speaker can incur damage in the event of a fall.

Do not attach the metal catch directly to the wall. It should only be used in conjunction with reinforced string to prevent the speaker from falling.

Metal catch

Sufficiently thick cord

Backside of speaker

Pass two reinforced strings through the metal catch, and fasten the speaker to the wall as shown above.

Do not place the speaker where it will be in direct sunlight, and avoid positioning it near heaters and air conditioners. Doing so may cause warping and discoloration of the speaker cabinet and damage to the speaker.

Pioneer assumes no liability whatsoever for damages resulting from assembly, improper mounting, insufficient reinforcement, misuse of the product, acts of nature, etc.

Mounting pad

Do not place the speaker on an unstable surface. It could present a hazard if it falls, as well as damaging the equipment.

As a precautionary measure, be sure to not place the unit anywhere where it might fall on a sleeping individual in the event of an earthquake.

As this unit weighs some 48 kg, it is very dangerous to try and set the spike nut while tilting the speaker. Be sure to place the unit on a soft area (such as a blanket) so that it does not damage the floor, and carry out the installation with at least two people.

6

En

Image 6
Contents Page Contents Before you start What’s in the boxAbout the EX series Technology behind the S-3EXCeramic Graphite Diaphragm Crossover Networks Bass DriversBass Enclosure Construction Collaboration with Air StudiosMounting the Fall-Prevention Fastener Installation and PlacementHow to install Metal catch Sufficiently thick cord Backside of speakerChoosing Where To Place The Speaker Systems Cm to 60 cmLeft Right Cm to 60 cm Short bar connectors Connecting to an amplifierConnecting the cables ConnectionsSingle-Wire Connections Only one channel shownBi-Amplification Connections Vertical Bi-AmpingHorizontal Bi-Amping Other Information Cleaning the speaker cabinetSpecifications Attaching/Removing the Grille CoverConnexions Installation et placementInstructions d’installation Fixation de l’attache antichute Autres informationsContenu de l’emballage Précautions d’installationAvant de commencer Précautions d’emploiDiaphragme en graphite céramique Propos de la série EXTechnologies à l’appui du S-3EX AluminiumFiltres Haut-parleurs de gravesEbénisterie Collaboration avec Air StudiosFixation de l’attache antichute Installation et placementInstructions d’installation Cales de liègeChoix d’un emplacement pour les enceintes acoustiques 30 cm à 60 cmEnceinte Gauche Droite 30 cm à 60 cm Câblage ConnexionsConnexions à un amplificateur StrapsMono-câblage Seule une voie est indiquéeCâblage pour bi-amplification Bi-amplification verticaleBi-amplification horizontale Entretien de l’enceinte Autres informationsMise en place et retrait de la grille Fiche techniqueInstalación y situación ConexionesInformación adicional Precaución instalación Antes de comenzarContenido de la caja Precaución durante la utilizaciónDiafragma de grafito cerámico Acerca de la serie EXTecnología que respalda el S-3EX AluminioRedes de frecuencias de cruce Excitadores de gravesConstrucción de la caja acústica de graves Colaboración con Air StudiosMontaje del fijador de seguridad contra caídas Instalación y situaciónModo de instalación Almohadilla de montajeCm a 60 cm Altavoz Izquierdo Derecho Cm a 60 cmPosición de audición Conexión de los cables ConexionesConexión al amplificador Barra cortocircuitadora Terminal negro Terminal rojoConexiones de un cable sencillo Sólo se muestra un canalDos amplificadores en horizontal Conexiones para dos amplificadoresDos amplificadores en vertical PrecauciónLimpieza Información adicionalColocación/extracción de la cubierta de rejilla Especificaciones如何安裝 安裝防落緊固件 選擇安置揚聲器系統的地方 連接於放大器 電纜的連結 單線連接 雙線連接 雙放大器接線 格柵蓋的裝卸 揚聲器機箱的維護 規格開始之前 關於 EX 系列 速度m/s精密曲線 中國語 安裝與設置 選擇安置揚聲器系統的地方 30 cm 到 60 cm連接於放大器 放大器(後) 雙放大器接線 其他資訊 如何安装 安装防跌落紧固件 选择安放扬声器系统的位置 连接到放大器 连接电缆 单线连接 双线连接 双功放连接 安装 / 拆除支架盖 清理扬声器机壳 规格包装箱内的零部件 关于 EX 系列 精密曲线 安装与放置 选择安放扬声器系统的位置 连接到放大器 放大器(背部) 双功放连接 其他资料 AFTER-SALES Service for Pioneer Products

S-3EX specifications

The Pioneer S-3EX stands out as a remarkable offering in the world of high-fidelity audio systems. Renowned for its impressive sound quality and dynamic performance, this speaker adeptly caters to audiophiles and casual listeners alike. The S-3EX is distinguished by its innovative technologies and thoughtful design, ensuring an exceptional listening experience across various genres.

One of the main features of the S-3EX is its unique construction that employs high-grade materials to facilitate superior sound reproduction. It is engineered with a robust cabinet designed to minimize resonance and vibrations, which can interfere with audio clarity. The cabinet's shape and internal bracing contribute to an optimal acoustic environment, delivering clear and rich sound.

The speaker utilizes a three-way design, incorporating a 1-inch soft dome tweeter, a 4-inch midrange driver, and two 8-inch woofers. This configuration allows for an extensive frequency response, ensuring detailed highs, articulate mids, and deep, powerful lows. The incorporation of dual woofers is particularly beneficial for bass-heavy music, providing a rich depth that enhances the overall listening experience.

One of the standout technologies featured in the S-3EX is Pioneer’s proprietary “Advanced Wide Dispersion” technology. This innovation ensures that sound is evenly distributed throughout the space, making it ideal for larger rooms or gatherings. Listeners can enjoy a consistent audio experience, regardless of their position in the room.

Additionally, the S-3EX benefits from Pioneer's “Natural Sound” philosophy, which aims to deliver music that accurately represents the original recording. This commitment to authenticity is realized through careful tuning and innovative engineering, making the S-3EX a true representation of Pioneer’s dedication to high-quality sound.

The sensitivity rating of the S-3EX is noteworthy, allowing for compatibility with a wide range of amplifiers and audio configurations. This versatility makes it an excellent choice for both dedicated audiophiles and those who may be exploring high-fidelity audio for the first time.

In summary, the Pioneer S-3EX combines exceptional build quality, innovative design, and advanced audio technologies to create a speaker that resonates with music lovers. Its three-way configuration, wide dispersion capabilities, and commitment to natural sound establish it as a standout choice in the high-fidelity speaker market, delivering an immersive audio experience that captivates and delights.