Diversity Wireless by Anchor Audio

Anchor Audio UHF wireless is a 16 channel, diversity wireless system that receives signals with two independent antennae. With diversity wireless the receiver processes the stronger signal, effectively minimizing dropouts and interference from other transmitting sources. The antennae are mounted internally so there are no obstructions or risk of damage.

FEEDBACK

Feedback, a howling noise or shrill sound, is self-generated by the sound system. It’s caused by a microphone picking up the sound coming from the speaker and then re-amplifying it. Once a feedback loop starts it continues until the system is adjusted.

CHANNEL SELECTION - BUILT-IN RECEIVER

Select a channel, set the built-in receiver & microphone transmitter to that channel before useing your wireless system.

1.Choose any available wireless channel/frequency from 1 thru 16 (see page 7 for transmitter setup instructions)

2.Turn the Wireless Channel Selector Knob to the channel/frequency you choose in step 1

If you have two wireless receivers repeat above for the second receiver. Remember each receiver/transmitter pair must be set to different channels for proper operation.

NOTE: Ongoing wireless interference? The frequency you selected may be in use by other systems in the area! Change channels until you find a clear frequency!

WIRELESS VOLUME	WIRELESS CHANNEL
CONTROL	SELECTION KNOB	CD SLOT

FEEDBACK CAUSES

•Microphone too close, pointing towards or in front of speaker

•Volume setting is too loud for room

•Sound reflecting off hard surfaces

AVOIDING & ELIMINATING FEEDBACK

•Point microphone in a different direction

•Keep microphone away from the speaker

•Place speaker in FRONT of the microphone

•Reduce the sound system volume levels

CORRECT SYSTEM PLACEMENT

WRONG SYSTEM PLACEMENT

CAUTION: Feedback can damage your equipment

& may be hazardous to hearing.

CONNECTING TWO OR MORE XTREME SOUND SYSTEMS

USING A XTREME UNPOWERED COMPANION SPEAKER (XTR-6001)

Connect one end of a speaker cable (SC-50NL) to the COMPANION SPEAKER OUTPUT jack on the back of a powered Xtreme sound system. Connect the other end to the jack labeled IN on the back of a Xtreme unpowered companion speaker.

NOTE: AC power is not required for an unpowered companion speaker.

RX INDICATOR LIGHTS

CD PLAYER LCD DISPLAY

CD POWER ON/OFF

OPERATING THE BUILT-IN CD PLAYER

Your built-in CD player features ‘direct-in’ play, power loading, anti-shock/skip CD mechanism, repeat & random play, three beam laser tracking system and dual one bit D/A converters. By feeding the CD audio signal directly into the mixing bus the Xtreme Sound System is able to create a crisp, clear composite output of all your system inputs.

CD PLAYER BASIC OPERATION

Insert a disc into the player by gently sliding it, label side up, into the CD slot. The player will automatically load and begin playback from the beginning of the disc. CD player controls are explained in detail below:

USING POWERED XTREME SYSTEMS

The Balanced Line Output feature allows you to connect two or more powered Xtreme’s and control all volume levels from the primary system.

1.Connect a speaker cable (EX-50PP) to the BALANCED LINE OUT jack on the first/primary powered Xtreme

2.Connect other end of cable to the BALANCED INPUT jack on the second powered Xtreme

3.Set the Level Control for the Balanced Input on the second Xtreme to maximum

4.Connect additional systems following 1 - 3 above

EX-50PP CABLE

FIRST POWERED

XTREME SYSTEMSECOND POWERED XTREME SYSTEM

PLAY/PAUSE	Press to play a loaded CD. Press during play-	TOP TRACK	Press once to start playing the disc from the
	back to pause, press again to resume.		first track.
UP	Press once to advance CD to next track. Press	RANDOM	Press for continuous, random track play-back.
	and hold to fast forward on the current track.		Press again to resume normal play.

NOTE: The Balanced Line Output feature can also be used to send the signal to a

sound system in a different room or a separate recording device.

DOWN	Press once to go to previous track. Press and	REPEAT	Press for continuous playback of the same
	hold to fast backward on current track.		track. Press again to resume normal play.
EJECT	Press to unload a disc from the player. If CD	POWER	Press to turn the CD player on/off. The sound
	is not removed within 10 seconds it will be		system will need to be turned off separately.
	automatically reloaded into the player.

CAUTION: To avoid noise at shut off, turn CD player off before you turn off the Xtreme!

SPEAKER STAND SETUP

1.Loosen the Lower Collar Knob

2.Separate the stand legs until the leg support Cross Braces are parallel to the floor

3.Tighten the Lower Collar Knob

UPPER

COLLAR

LOWERKNOB COLLAR

KNOB

CROSS BRACES

4.Loosen the Upper Collar Knob and extend the center pole

5.Adjust height and retighten the Upper Collar Knob

6.Place your Anchor sound system

on the stand	3
on the stand