CDN-32SE
PRE-PROGRAMMING AND EDITING A LOOP
LOOP IN PRE-PROGRAM
To
LOOP OUT PRE-PROGRAM
To
If you wish to precisely set the “LOOP OUT” point while searching;
a. press “PAUSE” once only before you reach the desired point, if you are currently in play.
b. turn the jog wheel until you find the desired point. c. hit “LOOP OUT” .
REVIEW YOUR LOOP
To review, press “RELOOP” only and the CD will begin playing the LOOP from the “LOOP IN” point so you may listen to the entire LOOP. DO NOT PRESS PLAY OR YOU WILL SET A
NEW “CUE” AND “LOOP IN” POINT AND ERASE THE “LOOP OUT” POINT! If you wish to advance quickly through a long loop, use the search wheel only.
If you wish to edit this point again;
a. Press “LOOP OUT” to release the loop. b. Repeat the above steps.
To review your loop while the CD is already playing press “CUE”. This returns the CD to the
“LOOP IN” point, then press play.
**Pressing the track buttons puts the CD player into an
PLAYING YOUR LOOP
To return to the beginning of the song and play after you are happy with the loop:
1.Press “PAUSE” to stop the play action of the CD or “CUE” to return to the “LOOP IN” point.
2.Track backwards until you reach the beginning of the song. (Remix CD’s often contain multiple track numbers for the same song.)
3.
4.The “LOOP OUT” LED will be flashing indicating a preset loop is ahead and will be played when reached.
5.When the “LOOP IN” point is reached both “LOOP IN” and “LOOP OUT” LEDs should flash.
6.The LOOP should occur as preset by you until you release it with the “LOOP OUT” button.
7.Both “LOOP IN” and “LOOP OUT” LEDs should then go solid again indicating the possibility of RELOOP.
NOTE: If you should decide that you do not want to automatically play a preset loop after you start a song, just press “LOOP OUT” anytime before you actually reach the “LOOP OUT” point and the “LOOP OUT” LED will remain solid. (You can press it again before the “LOOP IN” point if you change you mind.) The “LOOP IN” LED will come on solid when this point is reached indicating the possibility of RELOOP. This will allow you to use the selection for reloop purposes. However, until you pass the “LOOP OUT” point the “RELOOP/STUTTER” button only acts as a STUTTER function as explained in
STUTTERING FFFUN.
If you turned off your “LOOP OUT” while practicing your loop, remember to turn it on again before reaching the “LOOP IN” point.
ERASING YOUR LOOP
To erase presets loop either; a. Open and close the door.
b. Press the program button twice.
c. Select a track, a new “CUE” point, or new “LOOP IN” point beyond the “LOOP OUT” point.
d. Press “LOOP IN” prior to the old point to set a new loop.
DESCRIPTION OF LED DISPLAY
LOOP IN on /LOOP OUT off: This means that there is a LOOP IN point available for looping and stuttering, but no LOOP OUT point is set yet.
LOOP IN flashing /LOOP OUT flashing : This indicates that the CD player is actively looping from LOOP IN to LOOP OUT.
LOOP IN on /LOOP OUT on: This indicates that the LOOP IN and LOOP OUT points are set and a RELOOP will return to the LOOP IN to play the loop.
LOOP IN off /LOOP OUT off : This indicates that:
•There is a LOOP IN point stored into memory, but this looping function and this STUTTER point are disabled until the music plays through the point.
•There is no LOOP OUT point set yet.
LOOP IN off /LOOP OUT on: A future loop has been stored into memory. This loop will be inactive until either LOOP OUT is pressed prior to the CD playing through the LOOP IN point or RELOOP is pressed after the LOOP IN point.
LOOP IN off /LOOP OUT flashing : An active loop is stored into memory and will automatically play after the music plays through the LOOP IN point.
©2001 Numark Industries | - The Leader in DJ Technology | http://www.numark.com |
- 16 - |