Other connections | 08 |
Connecting a USB device
It is possible to listen to
USB mass storage device2 as shown below.
• Push down on the PUSH OPEN tab to access the
Basic playback controls
The following table shows the basic controls on the remote for USB playback. Press iPod USB to switch the remote control to the iPod USB operation mode.
Button | What it does |
|
|
Starts normal playback.
iPod DIRECT USB terminal.
| AUTO SURR/ | HOME | STANDARD | ADVANCED | STEREO/ |
|
|
|
|
| STREAM DIRECT | THX | SURROUND | SURROUND | A.L.C. | VIDEO INPUT |
| iPod DIRECT | MCACC |
|
|
|
|
|
|
| |||
|
|
|
|
| VIDEO | L AUDIO R | DIGITAL IN | USB | SETUP MIC |
PHONES |
| ST – | ST + |
|
|
|
| ||
| CONTROL | ON/OFF | SPEAKERS |
|
|
|
| ||
USB mass storage device
Connecting your USB device to the receiver
1Switch on the receiver and your TV.
2Press iPod USB on the remote control to switch the receiver to the iPod USB.
No Device appears in the OSD.
3Connect your USB device.3
The USB terminal is located on the front panel.
Loading appears in the OSD as this receiver starts recognizing the USB device connected. After the recognition, a playback screen appears in the OSD and
playback starts automatically.4
|
| Folder/File number |
USB | FLD004TRK001 | File format |
| MP3 | Repeat or Shuffle |
Pauses/unpauses playback.
/ Press to skip to previous/next track.
Press repeatedly to switch between Repeat
Folder, Repeat One and Repeat All.
Press repeatedly to switch between Shuffle On and Shuffle Off.
DISPLAY Press repeatedly to change the song playback information displayed in the front panel display.
/ During playback, press to skip to previous/next track.
TOP MENU Press to skip to first track.
Important
If a USB ERROR message lights in the display, try following the points below:
USB ERROR | What it means |
USB ERROR1 | The power requirements of the USB device |
| are too high for this receiver. |
|
|
USB ERROR2 | The USB device is incompatible. |
|
|
USB ERROR3 | See Troubleshooting on page 78 for more on |
| this error message. |
|
|
DECODE | There is some problem with the audio data or |
ERROR5 | the file’s additional information. |
R e l a x Yo u r B o dy |
|
|
|
|
| Song name | |
|
|
|
|
| |||
Kev i n J a ck s o n |
|
|
|
|
| Artist name | |
|
|
|
| ||||
We a r e a l l o n e |
|
|
|
|
| Album name | |
|
|
|
|
|
|
| |
|
|
|
|
|
| ||
Play | 0:01 |
|
|
| Elapsed time | ||
| |||||||
•Switch the receiver off, then on again.
•Reconnect the USB device with the receiver switched off.
•Select another input source (like DVD), then switch back to iPod USB.
•Use a dedicated AC adapter (supplied with the device) for USB power.
If this doesn’t remedy the problem, it is likely your USB device is incompatible.
Note
1This includes playback of
2• Compatible USB devices include external magnetic hard drives, portable flash memory (particularly keydrives) and digital audio players (MP3 players) of format FAT16/32. It is not possible to connect this receiver to a personal computer for USB playback.
•Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and assumes no responsibility for any loss of data that may occur when connected to this receiver.
•With large amounts of data, it may take longer for the receiver to read the contents of a USB device.
3Make sure the receiver is in standby when disconnecting the USB device.
4• If the file selected cannot be played back, this receiver automatically skips to the next file playable.
•When the file currently being played back has no title assigned to it, the file name is displayed in the OSD instead; when neither the album name nor the artist name is present, the row is displayed as a blank space.
•Note that
•It is not possible to output the USB audio to ZONE 2.
5• If this error occurs, playback is interrupted and the next playable file is played automatically.
•This error may occur if the title information is changed on a computer, etc.
53
En