Pioneer VSX-LX51 manual Additional information Chapter, Troubleshooting, Power, No sound

Page 78

13Additional information

Chapter 13:

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized independent service company to carry out repair work.

Power

Symptom

Remedy

The power does not turn on.

• Make sure that the power cable is plugged in to an active power outlet.

 

• Try disconnecting from the power outlet, then plugging back in.

 

 

The receiver suddenly switches

• Check that there are no loose strands of speaker wire touching the rear panel or another set of

off or the PHASE CONTROL

wires. If so, re-attach the speaker wires, making sure there are no stray strands.

indicator blinks.

• The receiver may have a serious problem. Disconnect from the power and call a Pioneer authorized

 

independent service company.

 

 

During loud playback the

• Turn down the volume.

power suddenly switches off.

• Lower the 63 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 41.

 

• Try switching on the digital safety feature (put the receiver into standby, hold down the

 

ADVANCED/SURROUND button on the front panel and press  STANDBY/ON to switch between

 

SAFETY 1 ON (medium effect), SAFETY 2 ON (more effect) and SAFETY OFF). If the power switches

 

off even with SAFETY 2 ON, turn down the volume. With SAFETY 1 ON or SAFETY 2 ON on, some

 

features may be unavailable.

 

 

The unit does not respond

• Try switching the receiver off, then back on again.

when the buttons are pressed.

• Try disconnecting the power cable, then connect again.

 

 

AMP ERR blinks in the display,

• The receiver may have a serious problem. Do not try switching the receiver on. Contact a Pioneer

then the power automatically

authorized independent service company for help.

switches off. The MCACC

 

blinks and the power does not

 

turn on.

 

 

 

AMP OVERHEAT blinks in the

• Allow the unit to cool down in a well-ventilated place before switching back on. Check the safety

display, then the power

precautions on page 2 for information on improving heat dispersal.

automatically switches off.

 

 

 

Display blinks 12 TRG ERR.

• An error has arisen in the 12 V trigger jacks. Reconnect accurately then turn the power back on.

 

 

The receiver suddenly switches

• The receiver may have a serious problem. Do not try switching the receiver on. Contact a Pioneer

off or DIGITAL PRECISION

authorized independent service company for help.

PROCESSING indicator blinks.

 

 

 

No sound

Symptom

No sound is output when an input source is selected.

No sound output from the front speakers.

Remedy

•Check the volume, mute setting (press MUTE) and speaker setting (press SPEAKERS).

•Make sure the correct input source is selected.

•Check that the MCACC setup microphone is disconnected.

•Make sure the correct input signal is selected (press SIGNAL SEL). Note that when PCM is selected, you won’t be able to hear any other signal format.

•Check that the source component is connected properly (see Connecting your equipment on page 12).

•Check that the speakers are connected properly (see Connecting the speakers on page 20).

78

En

Page 77 Page 79
Image 78
Page 77 Page 79
Contents Operating Instructions Important the Moulded Plug Risk of Electric Shock Do not OpenOperating Environment Contents Other connections Other SettingsUsing other functions Hdmi ControlFeatures Before you startBefore you start Chapter Checking what’s in the box Installing the receiverBefore you start Loading the batteriesIntroduction to home theater Minute guide02 5 minute guide Chapter Listening to Surround SoundFollow the instructions on-screen Playing a source Problems when using the Auto Mcacc Setup02 5 minute guide Select the input source you want to playPhase Control OFF Better sound using Phase ControlPhase Control on Minute guideConnecting your equipment Connecting your equipment ChapterConnecting your equipment Connecting your equipment When making cable connections About the video converterConnecting your equipment Connecting using Hdmi About HdmiConnecting your equipment Connecting your TV and DVD player Connecting your Blu-ray disc playerFor a second recorder, use the DVR2 in inputs Using the component video jacks Connecting digital audio sourcesConnecting analog audio sources Connecting a component to the front panel inputsAbout the WMA9 Pro decoder Connecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersConnecting antennas THX speaker system setupConnecting external antennas Plug the power cord into a power outletPlugging in the receiver Front panel Controls and displaysControls and displays Chapter 13 14Operating range of remote control unit Controls and displaysSpeakers Controls and displays Display Controls and displays Remote control RECEIVERMute TV CtrlSOURCE ReceiverAuto playback Listening to your systemListening to your system Chapter Listening in surround soundListening to your system Using the Home THX modesUsing the Advanced surround effects PRO LOGIC+THX CinemaUsing Front Stage Surround Advance Listening in stereoTip Choosing the input signal Listening to your system Using Stream DirectSelecting Mcacc presets Hdmi Digital AnalogUsing surround back channel processing Using the Virtual Surround Back modeAuto Sources Saving station presets Using the tunerUsing the tuner Chapter Listening to the radioListening to station presets Using the tunerNaming station presets An introduction to RDSUsing EON Displaying RDS informationMaking receiver settings from the System Setup menu System Setup menuSystem Setup menu Chapter Automatic Mcacc ExpertSetting , Channel Level , Speaker Distance and EQ System Setup menuCustom Menu The default is ALL recommended Options are ALL , Keep SP System , 6 SpeakerIf necessary, confirm the speaker configuration in the OSD.1 Surround back speaker setting Manual Mcacc setupFine Channel Level Adjust the level of the left channelSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Fine Speaker DistanceAdjust the parameters for the Standing Wave Control Acoustic Calibration EQ AdjustSelect ‘Standing Wave’ from the Manual Mcacc setup menu Select ‘EQ Adjust’ from the Manual Mcacc setup menuSelect the channels you want and adjust to your liking How to interpret the graphical outputHow to use Acoustic Calibration EQ Professional Acoustic Calibration EQ ProfessionalUsing Acoustic Calibration EQ Professional Select ‘EQ Professional’, then press EnterSelect an option and press Enter Select the setting you want to check Checking Mcacc preset dataSelect ‘Data Management’ from the System Setup menu Data ManagementClearing Mcacc presets Manual speaker setupRenaming Mcacc presets Copying Mcacc preset dataSpeaker Setting Select ‘Speaker Setting’ from the Manual SP Setup menuChannel Level Speaker Distance THX Audio Setting CurveOther connections Connecting an iPodConnecting your iPod to the receiver Other connections ChapterBasic playback controls Switching the iPod controls2Other connections ReturnBasic playback controls Other connections Connecting a USB deviceConnecting your USB device to the receiver Connect your USB device.3About MPEG-4 AAC Compressed audio compatibilityOther compatibility information About WMASwitching the speaker system Other connections Connecting the multichannel analog inputsSpeaker B setup Selecting the multichannel analog inputsBi-wiring your speakers Bi-amping your front speakersConnect your speakers as shown below MULTI-ZONE listening Making MULTI-ZONE connectionsLarge Surround Back System MULTI-ZONE setup Zone Using the MULTI-ZONE controlsBasic MULTI-ZONE setup Zone MULTI-ZONE listening optionsConnecting an IR receiver MULTI-ZONE remote controlsUsing this receiver with a Pioneer flat screen TV Pioneer flat screen TVUsing the SR+ mode with a Pioneer flat screen TV Other connections Connecting a PC for Advanced Mcacc output Advanced Mcacc output using your PCSelect ‘Output PC’ and press Enter Hdmi Control Setting the Hdmi optionsSetting the Hdmi Control mode Hdmi Control ChapterHdmi Control Before using synchronizationSynchronized amp mode About Hdmi ControlInput Setup menu Other SettingsOther Settings Chapter SetupInput function default and possible settings Other SettingsOther Setup menu Select ‘Other Setup’ then press EnterMulti Channel Input Setup Zone Audio SetupSelect ‘SR+ Setup’ from the Other Setup menu SR+ Setup for Pioneer flat screen TVsOSD Adjustment Select the ‘PDP Volume Control’ setting you wantSetting the Audio options Using other functionsUsing other functions Chapter Press Return to confirm and exit the menuUse / to select the setting you want to adjust Using other functionsSetting the Video options Press RECEIVER, then press Video ParameterPrepare the source you want to record Making an audio or a video recordingSelect the source you want to record Prepare the recorderChecking your system settings Using the sleep timerSwitching the speaker impedance Dimming the displayPress the front panel Auto SURR/STREAM Direct button Using other functions Resetting the systemDefault system settings Press Home THX to confirmSelecting preset codes directly Setting the remote to control other componentsPreset code list Controlling the rest of your systemCatv Controlling the rest of your systemVCR TapeControls for TVs Controls for other componentsHDD Decide which component you want to use the remote sensorDisplay Continue the chain in the same way for as manyAdditional information TroubleshootingPower Additional information ChapterAdditional information Other audio problems Settings VideoSignal SEL button Professional Calibration EQ graphical outputDisplay Remote control USB interfaceReceiver to a component or TV with the DeepColor feature Or other setting for your componentOther setting for your component Hdcp Error showsConfiguration a Configuration BImportant information regarding the Hdmi connection Additional information Surround sound formats DolbyDTS Neo6 Windows Media Audio 9 ProfessionalDTS Digital Surround DTS 96/24Additional information About THX About Neural THX Surround Stereo 2 channel signal formats ON/AUTOPRO Logic +THX PRO LogicMultichannel signal formats DTS +Neo6 DTS +Neo6 +THX Cinema Pro Logic llx Music +THX a EX +THX Games bConnected Not connectedAdditional information Specifications Cleaning the unitPioneer Corporation
Top Page Image Contents