Pioneer VSX-9130TXH-K Jacks, Video jacks between source and receiver, Output, Audio connection

Page 88

13Additional information

HDMI

Symptom

Remedy

The HDMI indicator blinks

• Check all the points below.

continuously.

 

 

 

No picture or sound.

• This receiver is HDCP-compatible. Check that the components you are connecting are also HDCP-

 

compatible. If they are not, please connect them using the component, S-Video or composite video

 

jacks.

 

• Depending on the connected source component, it’s possible that it will not work with this receiver

 

(even if it is HDCP-compatible). In this case, connect using the component, S-Video or composite

 

video jacks between source and receiver.

 

• If the problem still persists when connecting your HDMI component directly to your monitor,

 

please consult the component or monitor manual or contact the manufacturer for support.

 

• If video images do not appear on your TV or flat panel TV, try adjusting the resolution, DeepColor

 

or other setting for your component.

 

• If ‘NOT SUPPORT’ appears in the receiver’s display, try adjusting the resolution, DeepColor or

 

other setting for your component.

 

• While analog video signals are being output over HDMI, use a separate connection for audio

 

output.

 

• When this receiver reproduces MULTI CH IN audio sources with the HDMI setting set to

 

THROUGH, you cannot hear audio output from all channels. In this case, make a digital or analog

 

audio connection.

 

• To output signals in DeepColor, use an HDMI cable (high speed HDMI cable) to connect this

 

receiver to a component or TV with the DeepColor feature.

 

 

No picture.

• Try changing the Resolution setting (in Setting the Video options on page 74).

 

 

No sound, or sound suddenly

• Check that the HDMI AV setting is set to AMP/THROUGH.

ceases.

• If the component is a DVI device, use a separate connection for the audio.

 

• If analog video is being output over HDMI, please use a separate connection for the audio.

 

• Check the audio output settings of the source component.

 

 

Noisy or distorted picture.

• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the

 

video quality may just be poor (with some video game units, for example). The picture quality may

 

also depend on the settings, etc. of your display device. Switch off the video converter and reconnect

 

the source and display device using the same type of connection (component, S-Video or

 

composite), then start playback again.

 

• If the problem still persists when connecting your HDMI component directly to your monitor,

 

please consult the component or monitor manual or contact the manufacturer for support.

 

 

HDCP ERROR shows in the

• Check whether or not the connected component is compatible with HDCP. If it is not compatible

display.

with HDCP, reconnect the source device using a different type of connection (component, S-Video

 

or composite). Some components that are compatible with HDCP still cause this message to be

 

displayed, but so long as there is no problem with displaying video, this is not a malfunction.

 

 

88

En

Page 87 Page 89
Image 88
Page 87 Page 89
Contents VSX-9130TXH-K Operating Environment Federal Communications Commission Declaration of ConformityKeep in a Secure AREA. this is for Your Security Information to UserRisk of Electric Shock Do not Open Wash hands after handling Contents Other Settings Using other functionsOther connections Hdmi ControlBefore you start FeaturesBefore you start Chapter Installing the receiver Before you startChecking what’s in the box Loading the batteriesMinute guide Minute guide ChapterIntroduction to home theater Listening to Surround SoundFollow the instructions on-screen Problems when using the Auto Mcacc Setup Minute guidePlaying a source Select the input source you want to playBetter sound using Phase Control Phase Control onPhase Control OFF 02 5 minute guideConnecting your equipment Chapter Connecting your equipmentRear panel Connecting your equipment Connecting your equipment About the video converterConnecting your equipment Connecting using Hdmi About HdmiConnecting your equipment Connecting your TV and DVD player Connecting your Blu-ray disc playerFor a second recorder, use the DVR2 in inputs Using the component video jacks Connecting digital audio sourcesConnecting a component to the front panel inputs Connecting analog audio sourcesAbout the WMA9 Pro decoder Connecting your equipment Installing your speaker system Connecting the speakersPlacing the speakers Bare wire connectionsBanana plug connections Connecting antennas THX speaker system setupPlug the power cord into a power outlet Connecting external antennasPlugging in the receiver Controls and displays Controls and displays ChapterFront panel 13 14Controls and displays Operating range of remote control unitSpeakers Controls and displays Display Controls and displays Remote control RECEIVERTV Ctrl SOURCEMute ReceiverListening to your system Listening to your system ChapterListening in surround sound Auto playbackUsing the Home THX modes Using the Advanced surround effectsListening to your system THX SELECT2 GamesListening in stereo Using Front Stage Surround AdvanceTip Listening to your system Using Stream Direct Selecting Mcacc presetsChoosing the input signal Hdmi Digital AnalogUsing the Virtual Surround Back mode Using surround back channel processingAuto Pro and DVD-Audio stereo sources Analog 2-channel stereo sourcesDTS-HD Master Audio/DTS-HD DTS-EXPRESS encoded stereo SourcesUsing the tuner Using the tuner ChapterSaving station presets Listening to the radioUsing the tuner Naming station presetsListening to station presets AbcdefghijklmnopqrstuvwxyzSystem Setup menu System Setup menu ChapterMaking receiver settings from the System Setup menu Select the setting you want to adjustSystem Setup menu Custom Menu The default is ALL recommendedSetting , Channel Level , Speaker Distance and EQ Options are ALL , Keep SP System , 6 SpeakerIf necessary, confirm the speaker configuration in the OSD.1 Surround back speaker setting Manual Mcacc setupAdjust the level of the left channel Select ‘Fine SP Distance’ from the Manual Mcacc setup menuFine Channel Level Fine Speaker DistanceAcoustic Calibration EQ Adjust Select ‘Standing Wave’ from the Manual Mcacc setup menuAdjust the parameters for the Standing Wave Control Select ‘EQ Adjust’ from the Manual Mcacc setup menuHow to use Acoustic Calibration EQ Professional How to interpret the graphical outputSelect the channels you want and adjust to your liking Acoustic Calibration EQ ProfessionalSelect ‘EQ Professional’, then press Enter Using Acoustic Calibration EQ ProfessionalSelect an option and press Enter Select ‘Data Management’ from the System Setup menu Data ManagementChecking Mcacc preset data Copying Mcacc preset dataRenaming Mcacc presets Clearing Mcacc presetsSystem Setup menu Manual speaker setup Speaker SettingSelect ‘Manual SP Setup’, then press Enter Select ‘Speaker Setting’ from the Manual SP Setup menuSelect a setup option Confirm your selected setup optionAdjust the level of each channel using / Channel LevelSpeaker Distance THX Audio SettingCurve 5e.THX Audio Setting Loudness Plus SB SP Position Finish Connecting an iPod Connecting your iPod to the receiverOther connections Other connections ChapterSwitching the iPod controls2 Press iPod Ctrl to switch the iPod controls.3Other connections Basic playback controlsOther connections Connecting a USB device Connecting your USB device to the receiverSwitch on the receiver and your TV Basic playback controlsConnecting your XM Radio receiver Using XM RadioCompressed audio compatibility Saving channel presets Using XM HD SurroundListening to channel presets Listening to XM RadioUsing Sirius Radio Using the XM MenuConnecting your SiriusConnect Tuner Press Sirius to switch to the Sirius inputPress / to select the channel preset you want Using the Sirius MenuListening to Sirius Radio Other connections Connecting the multichannel analog inputs Speaker B setupSwitching the speaker system Selecting the multichannel analog inputsBi-amping your front speakers Bi-wiring your speakersConnect your speakers as shown below Other connections Connecting additional amplifiers MULTI-ZONE listeningMaking MULTI-ZONE connections LargeUsing the MULTI-ZONE controls Basic MULTI-ZONE setup ZoneSurround Back System MULTI-ZONE setup Zone MULTI-ZONE listening optionsConnecting an IR receiver MULTI-ZONE remote controlsUse the Master Volume dial to adjust the volume Press ControlUsing this receiver with a Pioneer flat panel TV Pioneer flat panel TVUsing the SR+ mode with a Pioneer flat panel TV Advanced Mcacc output using your PC Other connections Connecting a PC for Advanced Mcacc outputSelect ‘Output PC’ and press Enter Setting the Hdmi options Setting the Hdmi Control modeHdmi Control Hdmi Control ChapterBefore using synchronization Synchronized amp modeHdmi Control About Hdmi ControlOther Settings Other Settings ChapterInput Setup menu SetupOther Settings Other Setup menuInput function default and possible settings Press Receiver on the remote control, then press SetupMulti Channel Input Setup Zone Audio SetupSR+ Setup for Pioneer flat panel TVs OSD AdjustmentSelect ‘SR+ Setup’ from the Other Setup menu Select the ‘PDP Volume Control’ setting you wantUsing other functions Using other functions ChapterSetting the Audio options Press Return to confirm and exit the menuUsing other functions Setting the Video optionsUse / to select the setting you want to adjust Press RECEIVER, then press Video ParameterMaking an audio or a video recording Select the source you want to recordPrepare the source you want to record Prepare the recorderUsing the sleep timer Switching the speaker impedanceChecking your system settings Dimming the displayUsing other functions Resetting the system Default system settingsPress the front panel Auto SURR/STREAM Direct button Press Home THX to confirmSetting the remote to control other components Selecting preset codes directlyPreset code list Controlling the rest of your systemControlling the rest of your system Controls for TVsTV On or offControls for other components Decide which component you want to use the remote sensor  & EnterDisplay HDDTroubleshooting PowerAdditional information Additional information ChapterAdditional information Other audio problems Settings VideoProfessional Calibration EQ graphical output Signal SEL buttonDisplay Remote control USB interfaceOr other setting for your component Other setting for your componentReceiver to a component or TV with the DeepColor feature Hdcp Error showsConfiguration a Configuration BImportant information regarding the Hdmi connection XM radio messagesSirius radio messages Additional information Surround sound formats DolbyWindows Media Audio 9 Professional DTS Digital SurroundDTS Neo6 DTS 96/24Additional information About THX About Neural THX Surround About XM Radio XM Ready Legal Additional information About XMXM Ready Subscription ON/AUTO Stereo 2 channel signal formatsPRO Logic PRO Logic +THX Multichannel signal formats Pro Logic IIx Movie +THX a Pro Logic llxPro Logic llx Music +THX EX +THX Games b Pro Logic IIx Movie +THX aDTS +2 Pro Logic llx DTS +2 Pro LogicDTS +2 Pro Logic llx Movie +THX a DTS +Neo6 DTS +Neo6 +THX Cinema100 Connected Not connectedAdditional information Specifications Additional information Cleaning the unit To establish a safe levelOnce you have established a comfortable sound level Decibel Level ExamplePioneer Corporation
Top Page Image Contents