Pioneer VSX-9130TXH-K Making an audio or a video recording, Select the source you want to record

Using other functions

Setting	What it does	Option(s)
V. CONV	Converts video signals for output	ON
(Digital	from the MONITOR OUT jacks for
		OFF
Video	all video types.
Conversion)
BRIGHT	Adjusts the overall brightness.	–10 to +10
(Brightness)		Default: 0
CONTRAST Adjusts the contrast between		–10 to +10
	light and dark.	Default: 0
HUE	Adjusts the red/green balance.	–10 to +10
		Default: 0
CHROMA	Adjusts saturation from dull to	–10 to +10
	bright.	Default: 0
RESa	Specifies the output resolution of	AUTO
(Resolution)	the video signal (when analog
		PURE
	video input signals are output at
	the HDMI OUT connector, select	480p/576p
	this according to the resolution of
		720p
	your monitor and the images you
		1080i
	wish to watch). When AUTO is
	selected, the resolution is	1080p
	automatically selected depending
	on the capability of the display
	connected to this receiver. When
	PURE is selected, the signals are
	output with the same resolution
	as when input.
ASPb	Specifies the aspect ratio when	THROUGH
(Aspect)	analog video input signals are
		NORMAL
	output at the HDMI output. Make
	your desired settings while	ZOOM
	checking each setting on your
	display.

a.When a resolution value is selected in this setting and the analog signals input are converted and output as HDMI signals, images may not appear depending on the video signals being input or the resolution of your monitor. Also, depending on the source component or the monitor being used, the output resolution may be different from this setting. Conversion to 1080p is available only for the input signals of 480i/576i/480p/576p. b.If the image doesn’t match your monitor type, adjust the aspect ratio on the source component or on the monitor.

11

Making an audio or a video recording

You can make an audio or a video recording from the built-in tuner, or from an audio or video source

connected to the receiver (such as a CD player or TV).1

Keep in mind you can’t make a digital recording from an analog source or vice-versa, so make sure the components you are recording to/from are hooked up in the same way (see Connecting your equipment on page 13 for more on connections).

Since the video converter is not available when making recordings (from the video OUT jacks) make sure to use the same type of video cable for connecting your recorder as you used to connect your video source (the one you want to record) to this receiver. For example, you must connect your recorder using S-Video if your source has also been connected using S-Video.

For more information about video connections, see Connecting a DVD/HDD recorder, VCR and other video sources on page 18.

				DIRECT	A.L.C.	STANDARD	ADV SURR
DVD	BD	TV	HDMI	HDD	DVD
				THX	STATUS		PHASE
DVR 1	DVR 2	CD	CD-R
				ANT		MPX	SIGNAL SEL
FM/AM	XM	SIRIUS	iPod USB				MEM
				AUDIO	DISPLAY	CH
INPUT			DIMMER
SELECT		2
1			3	TV CTRL		RECEIVER
GENRE	MCACC		SLEEP

1 Select the source you want to record.

Use the input source buttons (or INPUT SELECT).

•If necessary, press SIGNAL SEL to select the input signal corresponding to the source component (see Choosing the input signal on page 33 for more on this).

2 Prepare the source you want to record.

Tune to the radio station, load the CD, video, DVD, etc.

3 Prepare the recorder.

Insert a blank tape, MD, video, etc. into the recording device and set the recording levels.

Refer to the instructions that came with the recorder if you are unsure how to do this. Most video recorders set the audio recording level automatically—check the component’s instruction manual if you’re unsure.

4Start recording, then start playback of the source component.

Note

1• The receiver’s volume, Audio parameters (the bass/treble controls, for example), and surround effects have no effect on the recorded signal.

•Some digital sources are copy-protected, and can only be recorded in analog.

•Some video sources are copy-protected. These cannot be recorded.

75

En