Dynacord PowerMate 1600 owner manual Safety Component Must be Replaced by Original Part

Page 3
IMPORTANT SERVICE INSTRUCTIONS
These servicing instructions are for use by qualified personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the Operating Instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated „dangerous voltage“ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.

 

 

 

 

The exclamation point within an equilateral triangle

 

 

 

 

is intended to alert the user to the presence of

1.

 

Read these instructions.

important operating and maintance (servicing)

 

instructions in the literature accompanying the

2.

 

Keep these instructions.

appliance.

3.

 

Heed all warnings.

 

4.

 

Follow all instructions.

 

5.

 

Do not use this apparatus near water.

 

6.

 

Clean only with a dry cloth.

 

7.

 

Do not cover any ventilation openings. Install in accordance with the manufacture’s instructions.

8.

 

Do not install near heat sources such as radiators, heat registers, stoves, or other apparatus

 

 

(including amplifiers) that produce heat.

 

9.

 

Do not defeat the safety purpose of the polarized or the grounding-type plug. A polarized plug has two blades

 

 

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide

 

 

blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an

 

 

electrican for replacement of the obsolete outlet.

 

10.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

 

 

and the point where they exit from the apparatus.

 

11.

Only use attachments/accessories specified by the manufacturer.

12.

Unplug this apparatus during lightning storms or when unused for a long period of time.

13.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged

 

 

in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the

 

 

apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14.

Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids, such as vases,

 

 

are placed on the equipment.

 

15.

To completely disconnect this equipment from the AC Mains, disconnect the power plug from the AC receptacle.

16.

The mains plug of the power supply cord shall remain readily operable.

CAUTION:

1.Security regulations as stated in the EN 60065 (VDE 0860 / IEC 65) and the CSA E65 - 94 have to be obeyed when servicing the appliance.

2.Use of a mains separator transformer is mandatory during maintenance while the appliance is opened, needs to be operated and is connected to the mains.

3.Switch off the power before retrofitting any extensions, changing the mains voltage or the output voltage.

4.The minimum distance between parts carrying mains voltage and any accessible metal piece (metal enclosure), respectively between the mains poles has to be 3 mm and needs to be minded at all times. The minimum distance between parts carrying mains voltage and any switches or breakers that are not connected to the mains (secondary parts) has to be 6 mm and needs to be minded at all times.

5.Replacing special components that are marked in the circuit diagram using the security symbol (Note) is only permissible when using original parts.

6.Altering the circuitry without prior consent or advice is not legitimate.

7.Any work security regulations that are applicable at the location where the appliance is being serviced have to be strictly obeyed. This applies also to any regulations about the work place itself.

8.All instructions concerning the handling of MOS - circuits have to be observed.

NOTE:

SAFETY COMPONENT ( MUST BE REPLACED BY ORIGINAL PART )

31

Image 3
Contents PowerMate 1000/1600 Contents Safety Component Must be Replaced by Original Part Description Installation and ConnectionsInput Mono MICLine Setting Instructions InsertGain Page AUX / FX 1/2 MID EQMute Signal / Peak IndicatorVolume PANGain MIC Input Stereo15.MIC Stereo Input L/MONO REQ Section Line TrimAUX /FX AUX3/4 BAL SIGNAL/PEAKFX1/FX2 Effekt 1/2FX Start Programs Changing FX Start ProgramsEffekt Return Display30. UP/DOWN Peak LEDAUX3/4 Send AUX3/4 PostFeedback Filter Band Equalizer AUX3/4 VolumeStatus Indicators MasterMaster L + R Master LED-DISPLAYStandby PFL MasterRecord Send L/R Mono OutputMono OUT PhonesEQ Inputs / Outputs Power AMP InputsMain Inserts Main OutputsLamp XLR FootswitchPower Rear PanelSpeaker Outputs Right / Left LF-Cables Balanced or Unbalanced? Setting UP a Standard PA-SYSTEMCabling Speaker CablesSetting Up Sound Check Monitor Mix Main MixMaster Patchbay and Different Setup Alternatives Connection of an external power amplifierUsing the internal power amplifier for monitoring purposes Active 2-way stereo configuration Maximum amount of speakers in a passive configurationSpecifications Block Diagram ABMESSUNGEN/DIMENSIONS Page USA