Polk Audio RC6S owner manual Painting the Frame, Allow the speaker to dry fully before handling

Page 5

PAINTING THE FRAME:

1.Apply paint to exposed (unmasked) parts. Use two or more thin coats. Spray painting is recommended.

2.Remove the masking material as soon as you apply the final coat. This avoids peeling up the dried paint on the speaker along with the masking tape or paper later.

3.Allow the speaker to dry fully before handling.

PAINTING THE GRILLE:

1.The grille of your loudspeaker features an even, protective powder coating. This powder coating is an ideal primer.

2.Grilles must be spray painted. Do not use a brush. Thick, brushed paint may clog the grille holes.

3.If your speaker model features a removable fabric scrim, carefully remove it by peeling it away from the inside of the grille. Place this on a clean, flat surface where it will not get wrinkled [Figure 4].

4.After removing the grille from the speaker frame by carefully hooking it with a bent paperclip and pulling it gently away from the frame, spray on two thin coats of finish color. If you’re using a compressor and spray gun, use the finest, most diffuse setting. Be careful not to fill the holes in the grille with paint. [Figure 5]

5.If your speaker model features a removable fabric scrim, carefully press the fabric scrim back into place on the inside of the grille before replacing the grille. The speaker fabric scrim hides the speaker’s drivers from view and will not interfere with the sound.

6.When the paint is completely dry, carefully reinstall the grille by fitting it into its recess so that it is just resting on the frame. Starting with one side, go around the speaker and push the grille into the grille notch a little bit at a time. Be gentle: the grille may be easily bent out of shape by rough handling. You will feel a positive “snap” when it is fully in place.

PEINTURE DU CADRE:

1.Appliquez deux minces couches de peinture (ou plus) aux pièces non masquées. Il est recommandé de vaporiser le cadre de peinture.

2.Retirez les cache-peinture et le ruban-cache dès que vous aurez appliqué la deuxième couche; cela évitera plus tard d’arracher la peinture séchée avec les cache-peinture et le ruban-cache.

3.Laissez sécher la peinture complètement avant de manipuler le haut-parleur.

PEINTURE DE LA GRILLE

1.La grille des haut-parleurs est enduite d’une peinture protectrice. Cette peinture constitue un apprêt idéal.

2.Les grilles doivent être vaporisées. N’utilisez pas de pinceau. La peinture plus épaisse appliquée au pinceau pourrait boucher les trous.

3.Si la grille de votre haut-parleur est munie d’une toile intér- ieure, retirez-la délicatement. Posez-la ensuite sur une surface propre et plate pour qu’elle ne se froisse pas [Figure 4].

4.Après avoir dégagé la grille (à l’aide d’un trombone plié) et de l’avoir retirée du cadre, vaporisez-la de deux minces couches de peinture de finition. Si vous utilisez un compresseur ou un pistolet pulvérisateur, choisissez le réglage le plus fin, le plus diffus. Assurez-vous de ne pas boucher les trous de la grille avec la peinture [Figure 5].

5.Si la grille de votre haut-parleur est munie d’une toile intérieure, replacez-la délicatement dans la grille avant d’installer cette dernière. Cette toile cache les composants et ne nuit pas au son.

6.Lorsque la peinture est complètement sèche, replacez la grille en la posant d’abord délicatement sur le cadre; en commen- çant par un coin, poussez petit à petit la grille dans son enc- oche tout autour du cadre. Soyez délicat, la grille peut être facilement déformée. Vous sentirez la grille «cliquer» en place.

FIGURE 4

Peel away fabric grille scrim before painting grille.

Retire la gasa difusora de la rejilla antes de pintar la rejilla.

Avant de peinturer la grille, détachez et enlevez le tissu.

Ziehen Sie den Stofffilter vom Schutzgitter, bevor Sie das Schutzgitter streichen.

FIGURE 5

Paint the grille. Use thin coats of spray paint.

Do not block grille holes with paint.

Pinte la rejilla. Aplique manos delgadas de pintura aerosol. No bloquee con pintura los agujeros de la rejilla.

Peinturez la grille. Appliquez des couches minces de peinture aérosol. N'obstruez pas les trous de la grille de peinture.

Streichen Sie den Gitteraufsatz. Verwenden Sie dazu dünne Spritzlackschichten. Die Öffnungen des Gitteraufsatzes dürfen nicht mit Farbe bzw. Lack blockiert werden.

For Customer Service, call 800-377-7655. 5

Image 5
Contents RCi Series Features Performance Enhancing AccessoriesAccessoires «AUDIO PERFORMANCE» CaracteristiquesFor Customer Service, call 800-377-7655 Safety FirstBlindage DES HAUT-PARLEURS Ou par courriel à polkcs@polkaudio.comPreparing to Paint Painting Your RC Series IN-WALL LoudspeakersPeinture DES HAUT-PARLEURS DE LA Serie RC Vous aurez besoin deAllow the speaker to dry fully before handling Painting the FramePainting the Grille Peinture DU CadreInstallation Dans LE MUR OU Dans LE Plafond Installation IN-WALL, IN-CEILING PlacementYOU will Need Vous Aurez Besoin DESuivez CES Simples Etapes Follow These Easy StepsBornes a Ressort Using Spring Clip ConnectorsIN-WALL Mounting Vous sentirez la grille «cliquer» en placeLimites D’OPERATION Safe Limits of OperationSpecifications Technical Assistance or ServiceService OU Assistance Technique Fiche TechniquePolk Audio Limited Warranty Metro Drive BALTIMORE, Maryland 21215, USA

RC6S specifications

The Polk Audio RC6S is a high-performance in-wall speaker designed to deliver exceptional sound quality while seamlessly integrating into your home environment. A part of Polk's extensive range of architectural speakers, the RC6S is designed for both audiophiles and casual listeners who appreciate premium audio without compromising on aesthetics.

One of the standout features of the RC6S is its innovative driver technology. It boasts a 6.5-inch Dynamic Balance composite driver that provides rich and detailed midrange and bass frequencies. This is complemented by a 1-inch silk dome tweeter that enhances high-frequency response, delivering clear and crisp sound quality across a wide frequency range. The combination of these elements allows the RC6S to reproduce music and dialogue with remarkable detail, making it an ideal choice for both home theaters and multi-room audio systems.

The RC6S also incorporates Polk's patented Power Port bass venting technology. This advanced design enhances the low-frequency response of the speaker, providing deeper, punchier bass without distortion. The Power Port technology allows for a smoother transition between the bass and midrange frequencies, resulting in a more dynamic listening experience.

Installation is made straightforward with the RC6S. It features an easy-to-install design, complete with a cut-out template and simple mounting clamps, enabling seamless integration into drywall and ensuring a secure fit. The low-profile grille can be painted to match your decor, allowing it to blend into any room without drawing attention.

In addition to its performance and design, the RC6S is engineered to be versatile. Whether you're listening to music, watching movies, or hosting parties, this speaker delivers a balanced and engaging soundstage. It is also compatible with other Polk Audio speakers, allowing for easy expansion of your audio system.

Durability is another notable characteristic of the RC6S. It is built with high-quality materials, ensuring long-lasting performance and reliability, even in challenging environments. The speaker is also moisture-resistant, making it suitable for use in humid areas like bathrooms or kitchens.

In summary, the Polk Audio RC6S is a premium in-wall speaker that combines advanced technology, high-quality sound reproduction, and versatile design. With features designed for both audiophiles and casual listeners alike, it represents a significant addition to any home audio system, offering a clean, unobtrusive aesthetic without sacrificing performance.